Bargain Bin
-
Super Fast FlyCat 56mm EDF Jet (KIT)$27.04This little kit takes around 4hrs to build and will satisfy the throttle jocky in all of us!
The flycat comes with 56mm EDF and you will need a 25A ESC & 4800kv inrunner.
This plane is extremely fast, (over 100mph!), however still stable at slow flight.
Spec.
WingSpan: 640mm
Length: 800mm
Weight: 290g
BESC : 25A (not included)
Motor: 4800kv 20-30 size Inrunner (not included)
Lipoly: 1300mAh 11.1v 20C (not included)Required.
Motor & ESC
3 x 9g Servo
5 or 10min Epoxy (Araldite)
1 x Servo Y lead
1 x Servo Extention lead
12AWG Silicon wire (20cm For motor to ESC)
1300mah 11.1v 20C lipo battery
Your own receiver and transmitterOur flight report.
Kit fits together well, light sanding of leading and trailing edges required to remove extra foam. We chose to not strengthen the wing with CF tubing, which didnt prove to be an issue, even at full speed high G turns.
We opted to mount the BESC being the battery area, in case the battery needed to be moved forward to adjust CofG, however this wasnt necessary.
EDF was mounted on the stick mount. Stick mount was shortened, with the extra piece used to raise the EDF off the stick to clear the EDF shroud. 2 bolts held the fan unit to the stick, one before and one after the fan blades.
First flight.
We kept CofG 9.5cm from the apex of the wings leading edge. The flycat was hand launched at 3/4 throttle, accelerating quickly. To our surprise, no trimming was required.
The flycat is an extremely fast kit to fly, and required a lot of elevator in turns. We suggest putting the elevator on maximum throws. It needs HUGE amounts of elevator during turns!
Overall an excellent plane which flys smoothly, even on windy days.
We suggest a good lipo pack, as this little hotty will chew through a 1500mAh in only 5 minutes. We used the ZIPPY-R 1800mAh 22C 3S1P pack for around 8 minute flights. As compared to the ZIPPY-Q pack which brought us short at about 7 minutes.
Learn More -
RC Controller Stick Ends. (JR)$5.99RC Controller Stick Ends. (JR) Add some bling style to your transmitter stick!Learn More -
P-51D Shangri La - Replacement Horizontal Tail$15.17P-51D Shangri La - Replacement Horizontal Tail
Learn More -
HobbyKing Helicopter Pitch Gauge Kit$6.26The HobbyKing helicopter pitch gauge is made from ultra-rigid fiberglass board and features dual ball bearings to ensure accurate measurements every time. This pitch gauge is supplied in kit form to keep production costs down which means we can pass the savings on to you!
Learn More
Specs:
Measurement: +/- 20 Deg
Size: 145mm x 105mm
Max Blade Width: 80mm
Note: An assembly guide can be found in the FILES tab below. -
Propeller Adapter (Collet Type) 4mm$2.37Propeller Adapter (Collet Type) 4MM
Spec:
Learn More
Motor Shaft: 4mm
Prop Shaft: 6mm
Prop Shaft length: 24mm
Weight: 14.2 grams -
Prop adapter w/ Alu Cone 4mm shaft (Grub Screw Type)$3.89Propeller adapter.
To suit;
4mm Motor Shaft.
6mmx20mm Propeller Shaft.
Alloy adapter with grub screw and alloy end cone.1pc Only.Learn More -
Anderson Powerpole Compatible PA45 Tube (10pcs/bag)$1.28Anderson Powerpole Compatible PA45 Tube (10pcs/bag)
Learn More -
Quanum 2.4Ghz Flexible Antenna.$5.25To be used with Quanum transmitter module.
Standard attachment fits most radio 2.4Ghz antenna location.The flexible antenna actually has a slightly better range than the standard antenna and can be used in difficult or small locations such as glider fuselages.
Learn More -
Turnigy D2830-11 1000kv Brushless Motor$14.50Learn MoreD2830-11 1000kv Brushless MotorSpecs:Rpm/V: 1000kvShaft: 3.17mm
Voltage: 2S~4S (7.4v to 14.8v)Weight: 52gWatts: 210w
Max Current: 21A
ESC: 30A
Suggested Prop: 8x4 (4S) ~ 10x7 (2S)
Mounting Hole Bolt Circle: 16mm or 19mmNOTE: This motor is 1000kv. The factory labelled them 1100kv in error. -
XT-60 to JST Charging Adapter (2pc)$2.29Use this adapter to convert an XT-60 Charge lead for charging JST equiped batteries.
Learn More -
-
-
-
Prop adapter w/Ally Cone M10x8mm shaft (Grub Screw Type)$3.42Prop adapter w/ Alu Cone M10x8mm shaft (Grub Screw Type).
Learn More
Specs:
Shaft Size: Suits 8mm motor shafts
Prop Mounting Thread: M10
Material: Aluminum
Quantity: 1pc -
-
-
FPV Tilt Camera Mount with Landing Gear$21.99The HobbyKing FPV tilt camera mounting system is a simple and easy way to mount your camera. Suitable for 450~500 class helicopters and made from light weight fibre glass material. The mounting plate features adjustable screw locations for mounting your heli and for relocating the camera mount to attain correct CoG. Kit includes screws, ball sockets, connection rods, linkages and pre-cut fiberglass board.Spec:Height: 185mm (to mounting plate)
Skid width: 190mm
Skid length: 290mm
Camera mount area width: 110mm
Camera mount area height: 100mm
Dry Weight: 188g (not including servo)Material: Fibre Glass
Required:1 x 9g ServoLearn More -
UltraDetail Scale Cockpit$8.75UltraDetail Scale Cockpit perfect for many scale glider applications!
Specs:
Width: 76mm
Length: 270mm
Heigth: 130mm
Learn More -
Insta-Cure IC-Gel .7 oz$6.88Insta-Cure IC-Gel .7 ozIC-GEL is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as MAXI-CURE; IC-Gel, however, can be applied to a vertical surface and will stay in place. It will not run. This can be very convenient for some assembly applications. Applying CA to the bottom of a horizontal surface, such as a ceiling, can be very difficult with anything other than a full standard CA bottle. IC-GEL can be applied at any angle with just a squeeze of the tube. The gel does, however, have a tendency to continue to come out of the tube for about a second after pressure is released, so this must be taken into account to apply the exact amount of IC-GEL that you want.IC-GEL is an excellent putty for plastic models. It will fill any void and can be formed to many shapes. Applying INSTA-SET allows IC-GEL to be sanded or filed to final shape in less than 20 seconds. Autobody repairmen have finished their jobs in a fraction of the time by using IC-GEL with the additional advantage over normal body putties of superior bonding to metal surfaces. IC-GEL, along with MAXI-CURE, is also used for the underwater bonding of coral to rock.Learn More -
Insta-Flex Plus Clear Rubber CA Glue 1. oz$7.85Insta-Flex Plus Clear Rubber CA 1. ozINSTA-FLEX+ clear rubber toughened has similar qualities to our black IC-2000 but can be used in applications where you do not want the adhesive to be seen. The carbon component of IC-2000 that gives the CA its black color also contributes to its unsurpassed strength. Since INSTA-FLEX+ has this carbon removed, its strength is a little less than IC-2000 but still superior to standard CAs. When aesthetics are important and a flexible bond is required, INSTA-FLEX+ is your best choice. It forms superior bonds to soft urethane and vinyl plastics. Both INSTA-FLEX and INSTA-FLEX+ work well when bonding R/C car tires. When a joint has a larger than normal gap, flexible CAs provide superior shock resistant bonds.Learn More -
Insta-Set CA Accelerator 2. oz$5.42Insta-Set CA Accelerator 2. ozINSTA-SET is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET significantly enhances a joints strength. For difficult to bond materials, INSTA-SET can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.Learn More -
Insta-Set CA Accelerator 8. oz$10.97Insta-Set CA Accelerator 8. ozINSTA-SET is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET significantly enhances a joints strength. For difficult to bond materials, INSTA-SET can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.Please note: This is a refill bottle only for a spray applicator, no spray nozzle is supplied with this product.Learn More -
HK-171 Thread Locker & Sealant Medium Strength (Blue)$4.99HK-171 is a medium thickness, medium strength threadlock that is applied to the threads of fasteners before assembly. Once HK-171 is cured, the fasteners can be disassembled with standard hand tools if required.Learn More -
HobbyKing® ™ GT-2 2.4Ghz Receiver 3Ch$7.60HobbyKing® ™ GT-2 2.4Ghz Receiver 3Ch.Please note: This receiver is compatible with the GT2E radio, the radio however will need to be switched to AFHDS1 protocol mode, this is outlined in the radio's user manual.Specification:Model: Car/BoatChannels: 3chFrequency band: 2.4GhzModulation: GFSKSensitivity: 1024RF. receiver sensitivity: -100dbmFail Safe: YesPower: 4.5~6VDCWeight: 5gAntenna length: 26mmSize: 37.6 x 22.3 x 13mmCE & FCC certified
Learn More -
HobbyKing 2.4Ghz Mode 2 4Ch Tx & Rx V2$27.97HobbyKing 2.4Ghz 4Ch Tx & Rx V2 (Mode 2)(THROTTLE ON THE LEFT)
HobbyKing's T4A 2.4ghz system is an entry-level transmitter offering the reliability of 2.4 GHz signal technology and a receiver.
The T4A makes a good backup transmitter or a take-anywhere unit. Drop it, scratch it, leave it in the car, and forget about it. This is what the T4A is all about.
Not suitable for the multi-flaperon, mixer, V-tail, FPV, robot-controlling hobbyist.Learn More -
-
HK-450 Glowing Tail and Light Set (Align part # HS1275)$4.06Night flying has never been more fun!
The HK-450 glow set includes flybar paddles, tail rotor and tail fins plus a resistored UV LED set that handles up to 13v! Perfect for 3S setups.
Installation is simple, just replace the standard flybar paddles, tail rotors and fins with our glow versions then install the UV LED to point towards whichever part you want to glow the brightest.
The UV-LED excites the luminescence material in the polymer causing it to glow brightly.Included.
HK-450 Flybar paddles.
HK-450 tail rotors.
HK-450 Tail fins.
80cm two wire lead (Pre-soldered)
Resistor (Pre-soldered)
High Power Directional UV-LED (Pre-soldered)(Similar Align part # HS1275)Learn More -
HK-500 Glowing Tail and Light Set (Align part # H50031).$4.06Learn MoreNight flying has never been more fun!
The HK-500 glow set includes tail rotor and tail fins plus a resistored UV LED set that handles up to 13v! Perfect for 3S setups.
Installation is simple, just replace the standard flybar paddles, tail rotors and fins with our glow versions then install the UV LED to point towards whichever part you want to glow the brightest.
The UV-LED excites the luminescence material in the polymer causing it to glow brightly.
Included.
HK-500 tail rotors.
HK-500 Tail fins.
80cm two wire lead (Pre-soldered)
Resistor (Pre-soldered)
High Power Directional UV-LED (Pre-soldered)(Similar Align part # H50031) -
Replacement Propeller Blade Set for Durafly Curtiss P-40N Warhawk.$5.31Replacement propeller blade set for Durafly Curtiss P-40N Warhawk.
Learn More -
Durafly™ Micro Series - Replacement Motor MountSpecial Price $0.90 Regular Price $1.15Durafly® ™ Micro Series - Replacement Motor Mount
Learn More -
Super Kinetic - Replacement Folding Prop Blades (1pair)Special Price $2.50 Regular Price $3.09Super Kinetic - Replacement Folding Prop Blades (1pair)
Learn More -
Login and Registration Form