Bargain Bin

A replacement set of landing gear with wheels for the 750mm XFLY Sukhoi Su-27 Flanker.

A replacement tail cone for the blue 750mm XFLY Sukhoi Su-27 Flanker.

A replacement horizontal stabilizer with elevators for the 1000mm XFLY A-10 Thunderbolt II Twin.

A replacement pair of vertical stabilizers for the 1000mm XFLY A-10 Thunderbolt II Twin.

A replacement landing gear set with nose, and main gear legs with wheels for the 1000mm XFLY A-10 Thunderbolt II Twin.

A replacement set of landing gear with wheels for the XFLY F-22 Raptor Twin 40mm EDF Jet 702mm.

A replacement nose, and main wheels for the XFLY F-22 Raptor Twin 40mm EDF Jet 702mm.

Pioneer 1020mm - Replacement Horizontal Stabilizer

This 2.8mm IR lens, with a wide 156° viewing angle, a standard M24 x 0.5 thread with an aperture of F2.0 is suitable for 1/2.5" CCD chipsets. 

The lens comes complete with a molded mount and screws for attachment to your chosen camera board.

Specs:
Image format: 1/2.5" CCD
Angle of View: 156°
Aperture: F2.0
Mount thread: M24 x 0.5
Mount holes: 20 x Ø1.7mm
Size: 29 x 26mm
Weight: 25g

The flight mode switcher has been designed for open source autopilots such as APM, PX4 and Pix etc. It can switch the flight mode accurately and quickly and replaces the troublesome 2 stage and 3 stage switchers.

Users can set the parameters for the flight mode switcher on the unit and choose the most suitable modes for their requirements. The flight mode switcher features a stable performance, is easy to set up and is small and lightweight.

Typical flight modes are as follows:
• STA (Stabilized) Model will automatically level itself
• SIM (Simple) Allows you to control the movement of the model from the pilots point of view regardless of which way the model is facing
• ALT (Altitude Hold) When this mode is selected it will hold this altitude
• LOI (Loiter) Allows model to hover in the same spot on its own without any input from the pilot
• AUT (Auto) The model will follow a pre-programmed course stored in the autopilot
• RTL (Return to land) Once selected the model will return and land at the point of take-off

The flight mode switcher is simple to install on your transmitter but it is not "plug & play", there is a small amount of soldering involved inside the Tx. See under the "Files" tab for installation instructions.

Once installed on your transmitter and set up in "Mission Planner" it is very simple to use, just press the relevant mode button on the switcher and the model will go into that mode. There is an indicator light to show which mode has been selected and is in use.

Features:
• Allows the user to easily set 6 flight modes
• Simple and straightforward to install
• Compact and lightweight
• Status indicator lights

Specs:
Type: Flight Mode Switcher
Working Voltage: 3~5V
Modes: 6 selectable
Operating Temperature: -10°C~+60°C
Dimensions: 59 x 29 x 9.3mm
Weight: 13g

Included:
Flight Mode Switcher
Connection harness

The flying V is perhaps the best general purpose antenna in the lower frequencies. Suitable for medium range and altitude, this antenna has slightly lower gain verses the coaxial connected Dipole, however has a very uniform radiation pattern. This is perfect for acrobatic and sport flying where antenna polarization (angle) can vary. The 120 deg V gives the best compromise between radiation pattern and gain.

Specs:
Frequency: 1.3GMHz
Connection: RP-SMA
dbi: 1.9

The Vortex FPV Racer from ImmersionRC is an incredible piece of kit for the serious competitor, but like all things flying the ocassional mishap is inevitable!

This crash kit is a convenient way to keep a stock of all of those plastic parts most likely to be damaged in a serious "departure from controlled flight"

Included are all parts which mount the motors to the carbon fiber arms, the plastic pivot points, foldable arm clips, and all other plastic parts.

No carbon fiber parts are included (see Crash Kit 2.)

Included:
1 x Front bumper (FR4)
2 x Side plates
8 x Arm clips
4 x Arm pivot tops
4 x Arm pivot bottoms
4 x Landing bumpers
4 x Landing mounts
4 x Motor mounts
8 x Hex bushes
1 x Camera support base
1 x Camera support arm
4 x Damper pins
4x Damper circlip
4x Screw HA2x8
4x Screw HA2x6

Hobbyking 1875mm B-17 F/G Flying Fortress (V2) (Silver) - Replacement Vertical Stabilizer

Hobbyking 1875mm B-17 F/G Flying Fortress (V2) (Silver) - Replacement Engine cowlings.

Hobbyking 1875mm B-17 F/G Flying Fortress (V2) (Silver) - Replacement canopy / battery hatch.

We all know the GoPro Hero as the take-it-anywhere workhorse of an action camera. Boldly going where no action cam has gone before; but how about giving your investment a little more protection from the dust and grime of everyday use?

Durafly® ™ Tundra - Decal Set (Orange/Grey)

Durafly® ™ Tundra - Decal Set (Blue/Red)

Replacement cowling for the H-King Voltigeur

Made of TPU material, this flexible camera mount fits the Foxeer Box Cam and other action cameras. The TPU creates a soft protective layer for the camera and absorbs excess vibrations.

Durafly T-28 Naval 1100mm - Horizontal Tail

Durafly T-28 Naval 1100mm - Canopy Inc FPV Pilot Tray

HobbyKing Bixler 2 EPO 1500mm - Replacement Fuselage (Blue/Red)

HobbyKing Bixler 2 EPO 1500mm - Replacement Canopy

HobbyKing Bixler 2 EPO 1500mm - Replacement Stabilizer (Blue/Red)

H-King Bixler 3 Glider 1550mm - Replacement Horizontal Stabilizer (Blue/Red)

H-King Bixler 3 Glider 1550mm - Replacement Vertical Fin (Blue/Red)

H-King Super Kinetic - Replacement Wings

Durafly Bonanza - Decal Set

Furious FPV is very quickly earning a reputation for producing high quality FPV products. Their build quality is excellent and the Poker Chip Antenna is no exception. The Poker Chip patch antenna is small and light with a 10dBi gain and is a perfect match to the Furious FPV Achilles Diversity Receiver Module. So if you are looking for a new antenna for your FPV goggles then look no further than the Furious FPV Poker Chip. See the attached manual for the radiation pattern and the S-Parameters.