FPV, Aerial Video & Telemetry

This 2.8mm IR lens, with a wide 156° viewing angle, a standard M24 x 0.5 thread with an aperture of F2.0 is suitable for 1/2.5" CCD chipsets. 

The lens comes complete with a molded mount and screws for attachment to your chosen camera board.

Specs:
Image format: 1/2.5" CCD
Angle of View: 156°
Aperture: F2.0
Mount thread: M24 x 0.5
Mount holes: 20 x Ø1.7mm
Size: 29 x 26mm
Weight: 25g

Circular polarized antenna's aka "clover leaf antennas" are a great way to increase the performance of your FPV system. The circular polarization helps reject “multipath interference”, a problem that plagues standard dipole stock antennas. Proven to increase range and video clarity, circular polarized antennas have become the standard after-market 'essential' upgrade for modern FPV systems. This is a matched 3 leaf Tx to 4 leaf RX set with no cable length for a nice clean, direct install with RP-SMA connectors.

Specs:
Frequency Range: 900MHz
Impedance: 50ohm
VSWR: <1.5
Gain: 5db
Connector: RP-SMA
Cable: RG141
Cable Length: 0m

The flying V is perhaps the best general purpose antenna in the lower frequencies. Suitable for medium range and altitude, this antenna has slightly lower gain verses the coaxial connected Dipole, however has a very uniform radiation pattern. This is perfect for acrobatic and sport flying where antenna polarization (angle) can vary. The 120 deg V gives the best compromise between radiation pattern and gain.

Specs:
Frequency: 1.3GMHz
Connection: RP-SMA
dbi: 1.9

The ImmersionRC 5v - 12v Step Up Converter provides power to drive 12v cameras from the 5v outputs of ImmersionRC's A/V transmitters.

The highly efficient step-up regulator, has almost zero RF emissions and with a 250mA maximum output current, the converter can power most of the commonly used FPV cameras. The step up converter is super lightweight and compact weighing in at just 2g.

Features:
• Converts 5V to 12v to power a multitude of FPV cameras
• 90% efficiency
• Super lightweight and compact (the size of a regular postage stamp)
• Minimal RF emissions

Specs:
Weight: 2g
Dimensions: 28 x 13 x 3mm
Material: PCB

The QE58-2 is a great micro 5.8GHz selectable 25mW ~ 200mW video transmitter. Small enough to fit on most multi-rotors but can also be used on other platforms.

This QE58-2 transmits a full range of 40 channels, weighs less than 17g (with supplied antenna) and incorporates a 5V power output for video cameras. Great for all FPV conditions. 

Selectable 200mW feature is activated by snipping the jumper wire in the bottom right hand corner of the VTX board.

Features:
• Micro sized and lightweight (7.5g)
• Easy install, plug and play
• Push button control instead of switch to change channels
• Selectable 25mW's ~ 200mW's (23dBm, +/-1dBm) of clean output power
• 5V Output for camera
• 40 Channels
• Microphone

Specs:
Modulate: Wideband FM
Video Format: NTSC/PAL
Output Impedance: 50 Ohm
Transmitter power: 25 ~ 200mW (23dBm, +/-1dBm)
Frequency range: 5645-5945MHz
Operating Voltage: 7~20V (2S~5S LiPoly)
Input current: 200mA
Output Voltage: 5V
Operating Temperature: -10~85deg C
Video Band Width: 0~8MHz
Audio Carrier Frequency: 6.5MHz
Video Input Level: 0.8~1.2Vp-p
Video Input Impedance: 75 Ohm
Audio Input Level: 0.5~2.0Vp-p
Audio Input Impedance: 10K Ohm
Weight: 7.5g
Antenna Connector: SMA Female
Size (LxW): 31x22mm (excluding antenna)

Included:
1 x Quanum ELITE QE58-2 5.8GHz Selectable 25mW ~ 200mW Wireless AV Transmitter
1 x SMA antenna
1 x Power in and video cable

Channels:
Band A: 5740, 5760, 5780, 5800, 5820, 5840, 5860, 5880
Band B: 5705, 5685, 5665, 5645, 5885, 5905, 5925, 5945
Band C: 5865, 5845, 5825, 5805, 5785, 5765, 5745, 5725
Band D: 5658, 5695, 5732, 5769, 5806, 5843, 5880, 5917
Band E: 5733, 5752, 5771, 5790, 5809, 5828, 5847, 5866

The Quanum Elite X50-2 transmitter packs 200mW of ultra clean 5.8GHz power for your FPV kit! This is a must have Tx for those who are looking for longer range.

The X50 transmits on the full range of 40 channels and has an easy to use channel switching system.

The unit comes in a unique metal alloy case that is not only damage resistant but also acts as a heat sink.  The case also has fixing points so that the unit can be bolted to your model making it far more secure.

A key feature of this system is the R Band also known as race band, which is 37mhz apart from the next channel, all 8 sub-channels in R Band will not interfere with each other, this is great news for FPV racers. 

Features:
• Bulit-in microphone 
• Super mini, light weight only 12.5g 
• Five bands 40 channels with R-Band 
• Elegant design with CNC aluminum case 
• One switching button for band and channel selection
• Vertical antenna connection

Specs: 
Video format: NTSC/PAL 
Antenna connector: SMA female connector (Vertical)
Power input: 7-20V (3S LiPo battery suggested) 
Power output: 5V 
Output impedance: 50 Ohm 
Transmitting power: 200mW 
Frequency range: 5645-5945Mhz 
Working current: 200mA at 12V 
Video bandwidth: 8Mhz 
Audio carrier frequency: 6.5Mz 
Audio input impedance: 10K Ohm 
Dimensions: 32x24x9.4mm
Weight: 12.5 grams

Frequency Range:
FRA: 5740MHz, 5760MHz, 5780MHz, 5800MHz, 5820MHz, 5840MHz, 5860MHz, 5880MHz 
FRB: 5705MHz, 5685MHz, 5665MHz, 5645MHz, 5885MHz, 5905MHz, 5925MHz, 5945MHz 
FRC: 5865MHz, 5845MHz, 5825MHz, 5805MHz, 5785MHz, 5765MHz, 5745MHz, 5725MHz 
FRD: 5658MHz, 5695MHz, 5732MHz, 5769MHz, 5806MHz, 5843MHz, 5880MHz, 5917MHz 
FRE: 5733MHz, 5752MHz, 5771MHz, 5790MHz, 5809MHz, 5828MHz, 5847MHz, 5866MHz  

Includes:
Quanum Elite X50-2  5.8GHz 40CH 200mW Wireless AV Transmitter 
Antenna 
Cable 
Manual

On screen display (OSD) module for Shark X6/X8 flight controllers.

Specs:
Input voltage: 5V DC
Operating Temperature: -10°C ~ 50°C
Cable length: 130mm
Dimensions: 33 x 20 x 11mm
Weight: 10.5g 

Included:
OSD module

The Lieber 5.8G FPV AV system is perfect for those who are looking for a solid performing AV TX/RX combination for their model that wont break the bank.

At home in FPV quads, planes, boats or cars with its compact design and capable of operating on any of 40 selectable channels including race band. 

Features:
• Bulit-in microphone
• Compact and light weight  
• Five bands 40 channels with R-Band
• Functional design perfect for FPV Racing
• Easy band and channel selection
• Vertical antenna connector

Specs:
Working Frequency: 5725~5917MHz
Working Voltage: 7.4 ~16V
Image Signal: NTSC/PAL
Antenna Connector: SMA (outer screw hole)
Operating Distance: Up to 4000 meters
Dimensions Receiver: 67 x 55 x 15mm
Weight Receiver: 57g
Weight Transmitter: 6.8g

Frequency Range:
FRA: 5740MHz, 5760MHz, 5780MHz, 5800MHz, 5820MHz, 5840MHz, 5860MHz, 5880MHz
FRB: 5705MHz, 5685MHz, 5665MHz, 5645MHz, 5885MHz, 5905MHz, 5925MHz, 5945MHz
FRC: 5865MHz, 5845MHz, 5825MHz, 5805MHz, 5785MHz, 5765MHz, 5745MHz, 5725MHz
FRD: 5658MHz, 5695MHz, 5732MHz, 5769MHz, 5806MHz, 5843MHz, 5880MHz, 5917MHz
FRE: 5733MHz, 5752MHz, 5771MHz, 5790MHz, 5809MHz, 5828MHz, 5847MHz, 5866MHz

Includes:
Lieber 5.8GHz 40CH 350mW Wireless AV Transmitter and Receiver
Patch Antenna
Circular Polarised Antenna
Cables 
Manual

Quanum Exoskeleton for RunCam

Are you worried about your RunCam action camera not surviving a hard landing?  Simply give your RunCam a rigid exoskeleton frame.

Manufactured from super light weight alloy and machined to allow easy access to all of the RunCams many functions while maintaining a clear view from the lens, this frame gives you peace of mind when you send your favorite action camera into the thick of it!

Features:
• Purpose made to fit the RunCam Action Camera
• Tough, exoskeleton style design
• Superlight Alloy
• Access to all camera functions
• Bolt together case
• Lens shield

Specs:
Dimensions: 69 x 46 x 23mm
Weight: 21.5g

This compact, lightweight power supply filter helps clean up dirty DC current that often causes lines in wireless video images. The filter is an LC type that uses large value inductor and capacitor components. Their values are robust enough to remove moderate amounts of power supply noise.

The filter reduces DC-DC switcher supply ripple and helps clean noisy power from a shared battery. For example, if your robot or R/C model's 12V motor battery also powers the video camera and A/V transmitter, then this LC filter can help reduce the video "noise" that may appear when the motor is running.

Note: Installations with severe power supply noise may not be fully cured with this filter. In such cases a shared battery should be avoided.

Features:
• L-C Filter circuit reduces DC supply noise
• Built-in Reverse Polarity protection
• Supports up to 14 VDC at 1.7 Amp (maximum)
• Compact design

Specs:
Voltage drop over filter: 225mV at 900mA
Impedence/ESR: 0.06Ohm at 100kHz/16V
Ripple Current: 1190mA
DC Resistance: 0.25 Ohm/path
Dimensions: 38x12.5x11.5mm
Weight: 6.4g

Upgrade your Quanum DIY FPV V2 Goggles with this V2 add on kit.  It incorporates many new features that you have all been asking for and will effectively bring your V2 Goggle set up to V2Pro specs at minimal cost. 

A new, clear acrylic three lens set (1X, 1.25X or 1.5X magnification) and lens frame adapter providing a superior improvement in quality over the previous fresnel lens set. 

A battery pouch with velcro flap and buckle has been added and is excellent for mounting your battery on to the goggle's headstrap (behind the user's head) and will take a battery up to 77mm x 35mm x 22mm.

An EVA foam adapter for mounting a smartphone onto your goggles will turn your V2's into a Virtual Reality headset for gaming etc. Recommended for smartphone sizes up to Samsung Galaxy S6. Smartphone ports are accessible on the ends and the V2's neoprene glove front straps will hold it in place.

Extra comfortable sponge rubber strips with double sided tape have been added for extra cushioning when wearing the goggles and are simply cut to size to match the users requirements. 

Features:
• New clear acrylic lens set and frame (1.0X, 1.25X and 1.50X magnification)
• Battery pouch
• Metal “S” loop for top strap adjustment to improve wearer comfort and fitting
• Extra comfortable sponge rubber cushoining strips for facial comfort
• EVA foam adapter for smartphone for mounting
• A set of extension/conversion cables including:
      a) 3.5mm female phone jack to 2.5mm male phone plug adapter
      b) FPV DC jack to 1x5521 DC plug, 2x3315 DC plug (Length = 350mm)
      c) 3.5mm phone female to RCA male cable (Length = 150mm)
      d) XT60 male to FPV DC jack (Length = 210mm)
      e) 3.5mm phone female to RCA female cable (lenght = 150mm)

Note: A set of modification instructions are located in the "Files" tab below showing the alternate mounting method for the goggle monitor allowing for an increase in focal plane length.

Also available for use with this product:

Quanum DIY FPV Goggle V2Pro Upgrade Glove (Urban Digital Cam)

Quanum DIY FPV Goggle V2Pro Upgrade Glove (Black/Red)

Quanum DIY FPV Goggle V2Pro Upgrade Glove (Fluro Pink)

SkyZone have forged a reputation for quality and reliability in their products having been tested and developed by FPV pilots. The SKY-N2000 Transmitter packs a whopping 2000mW of ultra clean 5.8GHz power! A must for those looking for longer range and locked in video. The N2000 can transmit a full range of 32 channels and is supplied complete with all connecting cables.
   
The N2000 boasts some impressive features including remote channel switching, meaning the transmitting band and channel can be changed remotely with a 3 position switch on your radio. This function allows you to quickly change to a clear band and frequency should you encounter interference on your existing channel.

Features:
• 128 x 64 super bright color digital display with brightness & contrast control
• Channel and frequency display
• 2w of transmitting power
• 2Ch video input, remote channel switching
• Support 2-6S LiPoly battery
• Battery Voltage display
• Screen Display: Current / Temperature / PA Power detection

Specs:
Operating Voltage: 6.5 ~ 28V
Output Power: 27dbm, 30dbm, 33dbm
Antenna Connector: SMA Male
Supply Current @12v: 0.5A, 0.6A, 1A
Operating Temperature: -10 ~ +80 Degrees
Voltage Detection Accuracy: ±0.05v, ±0.1V, ±0.5V
Current Detection Accuracy: ±0.05A, ±0.06AV, ±0.2V
Video Band Width: 5MHz, 6MHz, 6MHz
Video Input Impedance: 75Ω/1Vp-p
Audio Input impedance: 6.5M Hz
Audio Sub-Carrier: 4.7KΩ
Dimensions: 60x35x20mm
Weight: 47g

This is an all laser cut ply cockpit that has an integrated Pan and Tilt system and mounts for a complete FPV system. The Base frame has provisions for the FPV transmitter, wiring and battery. The Pan and tilt system has 2quick release mounting positions, the forward position giving an unobstructed clear view, well the back mounting position allows you to reuse the Lexan canopy for a sleek aerodynamic FPV rig. The Pan and Tilt hold a 180deg servo for pan and a 90 deg for tilt (not included). There are various mounting and access holes to accommodate a wide range of FPV cameras from board to cube style.

The Base frame has provisions for the FPV transmitter, wiring and battery. The Pan and tilt system has 2quick release mounting positions, the forward position giving an unobstructed clear view, well the back mounting position allows you to reuse the Lexan canopy for a sleek aerodynamic FPV rig. The Pan and Tilt hold a 180deg servo for pan and a 90 deg for tilt (not included). There are various mounting and access holes to accommodate a wide range of FPV cameras from board to cube style.

Features:
• Lasercut pre-built construction
• Can be adapted to other planes
• 2 mounting positions for the Quick release pan and tilt
• Mounting provisions for a full FPV system

Specs:
Weight: 78g
Size: 98x96x221mm WxHxL
Fitment: Direct fit for the Hawkeye 1700 PC FPV plane (can be adapted to others)

Required:
2 x 9g servos, recommend 180deg and Metal Gear.

Furious FPV is very quickly earning a reputation for producing high quality FPV products. Their build quality is excellent and the Poker Chip Antenna is no exception. The Poker Chip patch antenna is small and light with a 10dBi gain and is a perfect match to the Furious FPV Achilles Diversity Receiver Module. So if you are looking for a new antenna for your FPV goggles then look no further than the Furious FPV Poker Chip. See the attached manual for the radiation pattern and the S-Parameters.

The Aomway 5.8GHz circular polarized patch antenna is a lightweight directional antenna that is perfect for use with FPV goggles. It operates in the 5705~5945Mhz frequency bandwidth with an operating angle of 35° and has an incredible range. Flights of multi kilometers are possible even on CE legal 25mW, but with 600mW systems, the distance can be unbelievable.

The Foxeer Predator 5 series of FPV cameras are the perfect companion to the Foxeer F722 V2 standard and mini flight controllers. The Predator has a 150° field of view, super WDR function for improved contrast in different light conditions, 4-millisecond latency for virtually instant feedback, all of which make it perfect for FPV racing.