Battery Adaptors

EC3 Male - Tamiya Female 

Use this adapter to convert an XT-60 Charge lead for charging JST equiped batteries. 

HXT-4mm Plug Harness for 2S Hardcase Saddle pack Lipoly Batteries

Discharge Plug: HXT-4mm
Battery Plugs: 4mm Bullet Connetor
Balance Plug: JST-XH

This simple and effective charge lead comes pre-soldered with standard 4mm bullet connectors at the charger end and has stepped, bullet connectors at the battery end allowing you to charge hard case packs that utilise 4mm and 5mm connectors. 

This adapter will convert an HXT 5.5mm bullet equipped battery to an XT90 for use with an XT90 equipped ESC or an XT90 Charge lead.

This adapter will convert an XT90 equipped battery to an HXT 5.5mm bullet for use with an HXT 5.5mm bullet equipped ESC or an HXT 5.5mm bullet Charge lead.

A Parallel Harness is a common way to double the capacity rating (mAh) while keeping the same voltage.

XT30 Male Connector w/24AWG Silicone Wire 55mm (1pc).

One end has an XT60 male connector and the other end has a Micro Losi male connector.

XT60 Male to 2 x DC Jack Plug Connectors 220mm (2pcs)

Specs:
Connector 1: XT60 Male
Connector 2: 2 x DC Jack Plug
Length: 220mm
Weight: 16.7g each
Quantity: 2pcs

These are good quality balance lead extensions with a 5S JST-XH male connector on one end and a female on the other.

This compact adapter is perfect to convert an HXT3.5mm equipped battery to an XT60, or an XT60 charge lead to HXT3.5mm.

Specs:
Connector 1: HXT3.5mm
Connector 2: XT60 female
Weight: 15g (each)
Quantity: 2pcs

A compact battery adapter to convert a T-Connector battery lead to a TR output, compatible with similar types of connectors.

A compact battery adapter to convert an EC5 battery lead to a TR output, compatible with similar types of connectors.

A compact battery adapter to convert an EC3 battery lead to a TR output, compatible with similar types of connectors.

A compact battery adapter to convert an XT60 battery lead to a TR output, compatible with similar types of connectors.

A compact battery adapter to convert an XT90 battery lead to a TR output, compatible with similar types of connectors.

XT-60 Plug Harness for 2S Hardcase Saddle pack Lipoly Batteries

Discharge Plug: XT-60
Battery Plugs: 4mm Bullet Connetor
Balance Plug: JST-XH

Most standard 7S lithium polymer battery packs feature two balance ports, a 4S and 3S balance lead (total 7S). This makes it difficult to charge with most standard battery chargers that only feature one balance port.

With this super useful adapter you can easily charge your 7S battery with any standard 8~10S capable balance charger that accepts JST-XH balance plugs. This adapter takes the 4S and 3S individual plugs from your pack, and combines them to one single 7S balance plug which is able to connect to most standard 8~10S capable chargers.

Specs:
Input: 1 x 4S and 1 x 3S JST-XH balance plug
Output: 7S JST-XH balance plug
Length: 100mm

Most standard 6S lithium polymer battery packs feature two balance ports, 2 * 3S balance lead (total 6S). This makes it difficult to charge with most standard battery chargers that only feature one balance port.

With this super useful adapter you can easily charge your 6S battery with any standard 8~10S capable balance charger that accepts JST-XH balance plugs. This adapter takes the 2 * 3S individual plugs from your pack, and combines them to one single 6S balance plug which is able to connect to most standard 8~10S capable chargers.

Specs:
Input: 2 x 3S JST-XH balance plug
Output: 6S JST-XH balance plug
Length: 100mm

T-Connector Harness for 2 Packs in Parallel (1pc)

Spec:
Weight: 9.0g

XT60 Harness for 2 Packs in Parallel (1pc)

Spec:
Weight: 11.2g

IMPORTANT: "These are not cheap copied XT60 plugs. These original Nylon XT60 plugs, manufactured by AMASS, can handle over 60A current for extended periods without exceeding 80DegC thanks to their better contact surface area. The plug is also less likely to deform or melt in comparison to copied non-Nylon XT60 plugs."

JST-XH to JST LED Power Distribution Lead - A neat way to power LED's from 3s Lipoly's using the balance plug.



** WARNING: Check Polarity of your setup before connecting this harness.

This adapter will convert a T-Connector equipped battery to an XT60 for use with an XT60 equipped ESC or an XT60 Charge lead.

This handy connector set will be appreciated by anyone who is dealing with 'Header Pins' on Multirotor boards or any othe type of PCB.

This set consists of a 1 pin housing and 1 female terminal.

Flat style 'AAA' battery holder, holds 4 cells

This binding post set (1 Black, 1 Red) is ideal for building your own charging station or as a 12-24volt power access point for DC power applications.

They are designed to pass through wooden or metal facias up to 10mm thick (they are insulated and required a 7mm mounting hole). 

The output terminals have 4mm holes to suit 4mm male banana plugs, the terminal tips can be removed to allow aligator clamp access, the screw on terminal caps are insulated with a hard plastic shell.

Rated to around 50amps.

Spec:
Total length: 33mm
Depth: 10mm
Mounting hole: 7mm

HXT 4mm to T-Connector Battery Adapter Lead (2pc)

This adapter will convert an HXT 4mm equipped battery to a T-Connector for use with a T-Connector equipped ESC or Charge lead.

Spec:
Weight: 7g (Each)

This adapter will convert a 5.5mm Bullet Connector equipped battery to a T-Connector for use with a T-Connector equipped ESC or Charge lead.

Spec:
Weight: 9g(Each)

This adapter will convert a T-Connector equipped battery to an HXT 4mm for use with an HXT 4mm equipped ESC or Charge lead.

Spec:
Weight: 10g(Each)

This adapter will convert an HXT 4mm equipped battery to an XT60 for use with an XT60 equipped ESC or Charge lead.

Spec:
Weight: 10g(Each)

Finally, a simple solution to mis-matched plug types! This very neat, short one piece adapter is an easy way to convert your T-Connector to XT60. Simply plug your model's T-connector on the ESC into the back of this adapter and you can then use batteries with XT60 plugs in your model, it's that easy!

We have designed these plug adapters in-house and paid for the molding. This allows us to keep costs low and they are exclusive to HobbyKing, meaning you will not find these XT60 plug adapters anywhere else!

The XT60 adapters are made from high-temp nylon and gold plated spring connectors, both are included in the injection molding process at the time when forming the connector.

This set includes:
2 x XT60 Male to T-Connector Adapter Plug

Finally, a simple solution to mis-matched plug types! This very neat, short one piece adapter is an easy way to convert your EC3 plug to XT60. Simply plug your model's EC3 plug on the ESC into the back of this adapter and you can then use batteries with XT60 plugs in your model, it's that easy!

We have designed these plug adapters in-house and paid for the molding. This allows us to keep costs low and they are exclusive to HobbyKing, meaning you will not find these XT60 plug adapters anywhere else!

The XT60 adapters are made from high-temp nylon and gold plated spring connectors, both are included in the injection molding process at the time when forming the connector.

This set includes:
2 x XT60 Male to EC3 Adapter Plug