Civilian and Fun Flyer

Introducing our EPP 3D MX2. Featuring a fantastic design and layout, this all out EPP 3D'er will satisfy the most eager 3D pilots!

Its fuselage is torsionally very stiff yet light with loads of space beneath the long top hatch for your radio and power system. The wing is a one-piece affair featuring EPP construction, a very accurate symmetrical airfoil with 2 additional spars to minimize flex and twist. The control surfaces are something else - the elevator, rudder, and ailerons feature a 3 layer construction (Epp-Depron-EPP) making for stiff surfaces and NO flex at extreme throws! Snap rolls "Snap" and the control response is instantaneous.

The light - yet rigid - airframe adds up to one great flying 3D "foamy". Waterfalls, harriers, flat spins, rolling circles this model has the precision to perform these and any other moves you can think of!

Assembly of the airframe in a quick 10-15 minute process with the help of a little medium CA. The radio and power system layouts are very straightforward, the long top hatch making for easy access.

This is a great model for general park flying and hardcore 3D. You will be hard-pressed to break this model, it will take hard knocks and just keep bouncing back every time!


Features:
• Tough EPP material, light-weight, and crash-resistant
• Stiff EPP/Depron composite control surfaces
• Revolutionary design adds to the structural integrity and the rigidity of the airframe
• Light-weight provides optimal wing loading
• Outstanding aerobatic performance and 3D maneuverability.
• Simple design allows for easy equipment access and installation
• The stand out color scheme great for orientation


Specs:
Wingspan: 955mm
Length: 945mm
Wing Area: 15.2dm2
Weight: 550g (without battery)



Requires:
4 channel radio system
2217 950-1100KV Brushless outrunner 
30Amp ESC 
3S 11.1V 1100-1300MAH Li-Po 
10x4.7/11x4.7 propeller 
4 x 9g servos

The HobbyKing® ™ Walrus is a very capable, fun model that appeals to both new and experienced pilots alike. Easy to fly and easy to build, the Walrus is great value for money!

Made from tough EPO foam, the Walrus is simple to assemble, the colourful decals are pre-applied, and the brushless outrunner motor, ESC, and all servos are pre-installed, even the folding prop and spinner have been factory fitted! As well as being easy to assemble, the Walrus is very practical and features a stiff, CF-reinforced 2pc Plug-in-wing and a large canopy area that allows you to fit a wide range of lipoly packs. Its somewhat portly proportions also make the Walrus super easy to hand-launch. The great-looking scheme is perfect for orientation, and its appealing size gives the Walrus plenty of presence, as well as the ability to handle a little wind.

The Walrus is an extremely stable RC plane for the new flyer to the seasoned pro. Now you can light up the sky and enjoy the fun of night flying. LED super bright lights will light up your nightlife!

Take to the skies with this durable glider with optional FPV camera mounting. The Ranger 1600 is easy to assemble and features a large wingspan for stability in the air. The airfoil wings are fitted with two spars to strengthen the wings in high wind situations. Use the wing clips to click and plug the wings into the fuselage. After flying, simply squeeze the clips to release the wings and easily store the plane in your car.

Take to the skies with this durable glider with optional FPV camera mounting. The Ranger 2000 is easy to assemble and features a large wingspan for stability in the air. The airfoil wings are fitted with two spars to strengthen the wings in high wind situations. Use the wing clips to click and plug the wings into the fuselage. After flying, simply squeeze the clips to release the wings and easily store the plane in your car.

Looking for the perfect trainer? Or an in-expensive FPV platform? Maybe you are a club pilot looking for something you can just pull out of the car and fly on one of those lazy Sunday afternoons? The Hobbyking® ™ Bixler® ™ 2 ticks all of these boxes and more! The Bixler® ™ 2 has had some improvements to make it even better such as a bigger air inlet for better motor cooling.

Looking for the perfect RC trainer plane? How about a smooth RC glider or an inexpensive FPV platform? Maybe you are a club pilot looking for something you can just pull out of the car and fly on one of those lazy Sunday afternoons? The HobbyKing Bixler 2 does all that and more! This electric RC plane has undergone some major improvements including (but not limited to) bigger air inlets for better motor cooling of the uprated motor for even better performance. 

Improving on the Bixler 2, this latest model is the perfect RC trainer plane, the perfect RC glider, and the perfect beginner FPV plane. Attach your flight camera into the nose or canopy of the plane to enjoy First Person View while flying. The Bixler 3 PNF Plane is a plug-and-fly model requiring a radio system and battery.

If you're looking for a fast, fun, aerobatic sports model that can be flown just about anywhere, the H-King Super Kinetic is what you're after! From high-speed aerobatics including pylon style "bank and yank" flying to off-power gliding, the H-King Super Kinetic handles it all with ease. It's a truly versatile model that is a blast to fly.

The H-King Crusader 30E is based on the classic stick design. This electric RC plane can be flown by both beginners and experts. It is constructed from lightweight ply and balsa that is painted with a high contrast color scheme. The Crusader will stand out on the ground and in the air at your local hobby club.

The Bixler 1.1 is a proven platform for beginners right through to intermediate pilots. Well known for stability, the Bixler is also an excellent choice for an inexpensive FPV platform and perfect for those lazy Sunday afternoons.

This version of the Bixler 1.1 is not supplied with a motor, ESC, servos, or RC equipment, it allows you to choose yourself the components you wish to use. Whatever you are looking for, the Bixler 1.1 has it covered.

Made of tough EPO, the Phoenix V2 glider fuselage has been blow moulded with pylon formers to make it near indestructible. The Phoenix was made to last a lifetime with its smooth, rigid, yet remains light enough for the glider to perform. Assembly can be completed in under 15 minutes so you'll be flying in no time.

The Durafly SlowPoke is an EPO foam model of the classic balsa design. Adding to the easy flying design of the SlowPoke, Durafly has added some larger wheels to make it even easier to take off and land on a wide variety of local fields. A great plane for your first low wing tail dragger or for the discerning experienced pilot wanting a great looking plane.

The Bixler 1.1 is a proven platform for beginners right through to intermediate pilots. The Bixler 1.1 is made of super-tough EPO foam with all the electrical components pre-installed. The aircraft can be assembled in 15 minutes and flown as soon as the glue dries.

This great-looking little racer can trace its lineage back to the very popular Rare Bear which we sold a few years ago. This was a very fast parkflyer based on the Reno Racers that was amazing fun to fly, was very tough and it became a firm favorite extremely quickly.

The Phoenix 2400 is the largest glider in the Phoenix range. It comes with an almost indestructible ABS plastic hull and strong EPO foam wings and tail section. With its smooth, stiff hull, the Phoenix is ​​durable for a lifetime and yet light enough for the glider to work without any problems. An additional canopy with camera mount is included. Once you have your camera installed, you can either enjoy FPV flying or just take pictures of your flights.

The Durafly™ Ugly Stick V2 not only looks as good as the original but flies just as well too, perfectly capturing those excellent flight qualities of which the Ugly Stick was renown. Being the well mannered RC sports model it is, the Ugly Stick is suitable for both novice and experienced flyers alike. At the lower end of the speed range, it exhibits no bad stall tendencies and can be flown comfortably at half throttle if desired. However, when you wish to experience its true flying capabilities, open the throttle wide and the Ugly Stick will oblige, performing a full range of sport aerobatic maneuvers with the ease that made the original so popular. Due to the low current draw of the Ugly Stick V2 power system, you can also enjoy longer than average flying times with mixed power use.

The Ranger 2000 is easy to assemble and features a large wingspan which provides stability, and also allows the model to fly at slow speeds. The EPO wings are fitted with two spars for strength and each aileron is reinforced with carbon to eliminate any chance of distortion or twisting. The wings are attached to the fuselage using fast connect clips, after flying, simply squeeze the clips to release the wings.

The Phoenix 2400 is an extended wing version of the popular Phoenix 1600mm and 2000mm range of electric powered gliders. Assembly is quick and easy with no glue required, the vertical fin and horizontal stabilizer are simply screwed to the rear of the fuselage. The EPO wings are fitted with a carbon spar for strength and 2 metal spars join the wings to the fuselage. Also, each aileron is reinforced with carbon to eliminate any chance of distortion or twisting. The wings are attached to the fuselage using fast connect clips, after flying, simply squeeze the clips to release the wings.

Want a plane that can take on anything? Born from the same stable as our best-selling SkyMule, the AVIOS BushMule is the sturdy workhorse of the sky. Taking rough terrain, water, and snow in its stride, this Plug and Fly airplane uses twin motors for great sport flying and STOL capabilities.

The AVIOS BushMule V2 carries on the BushMule pedigree but with some improvements, these include:

• Upgraded servo connection for the steerable nose-wheel
• Re-positioned main landing gear, this has been moved further back
• Brass threads in the wing mounts
• Upgraded propellers and spinners as used on the popular Avios Albatross
• New, eye-catching color scheme

The Wargo Signature Edge 540T 3D is yet another incredible airplane in the series inspired by the renowned 3D pilot Michael Wargo. The Edge 540T was specifically designed for very precise 3D flying and aerobatic training. Michael Wargo, our team pilot, and 3D expert, wanted a foam aircraft that was stiffer, and lighter than other foamies. This was achieved by the combination of a stiff, lightweight balsa frame covered with lightweight, crash-resistant EPP foam.

The AVIOS Albatross HU-16 is a beautiful twin-engine flying boat with a large monohull, and wing floats, the entire underneath of the front portion of the hull is reinforced with plastic. This allows it to happily take the knocks and bangs of using a grass airfield to fly from, but as mentioned before, it really does come into its own when operating from your favorite lake or waterway. Taxi-ing, and lining up for take-off are made all that much easier with the water rudder and the supplied Aerostar forward/reverse water-resistant ESCs. Built-in flaps provide plenty of lift and make the landings and take-offs that much easier and extremely scale-like.

The Durafly Night Tundra follows in the footsteps of the popular and firmly established Tundra series. No longer do you have to finish flying when the sun sets, with the incredible, super-bright light system on the Night Tundra you can just carry on into the twilight and beyond. The Night Tundra retains the no-limits flying characteristics of the original Tundra. Whether it’s flying from rough bush fields, water, snow, or sand, aerobatics, glider towing, candy dropping (optional part), or just good old-fashioned super STOL slow-flying, the Night Tundra takes it all on with ease. Its lightweight yet rugged and beautifully finished EPO foam construction, powerful brushless set-up, and perfectly harmonized design give you instantly a feeling of confidence on the sticks as quickly as it puts a smile on your face.

The ZOHD Dart XL FPV flying wing airplane offers incredible lifting power, excellent handling, and portability, making it the ideal choice for long-range FPV flying. This "Enhanced Version" features a newly designed motor mount, a GPS bay with cover, built-in carbon fiber for strength, a new optimized airfoil, and a strengthened battery bay. The Dart XL incorporates Vortex generators and a swept forward wing for improved handling, lift efficiency, and yaw stability. It also has a computer-designed airflow pod that maximizes the cooling to all the onboard equipment to minimize overheating electronics and reduce the risk of failure. The vertical fins are detachable, making it much easier to transport to those out-of-the-way places for the best FPV experiences.

The OrangeRx R615X offers true DSMX compatibility and utilizes a dual antenna system to provide true signal reception diversity. Due to the previously used IC becoming obsolete, this latest R615X receiver has been redesigned, and now offers improved range and performance. Features that have been retained are the programmable failsafe on binding, ultra-fast brown-out recovery, and wide voltage input range. As we can maintain the same low price as before, this makes the latest R615X still unbeatable value for money.

When Durafly released the original Auto-G it raised the bar by being the first Plug-N-Fly autogyro on the market, that bar has been raised even higher with the Auto-G2 V2. Keeping to the Durafly tradition, it is quick and simple to assemble, flies extremely well, and looks amazing in flight. The V2 upgrades include the addition of a durable 2mm fiber-reinforced nylon head plate, fiber-reinforced pushrods, a fully encased main mast, wider, stronger landing gear with large lightweight bush-style foam wheels, and a cowled-in motor, plus smaller internal electronics giving more space for the flight battery.

The SonicModell Baby AR Wing PRO is a dynamic, tough, compact flying wing that will deliver an impressive performance. The Baby AR features detachable wings, so there is no glue required when assembling, and the wings can be easily removed for transport. Other features are a large battery bay, a nose camera bay for FPV flying, and a unique "FlexiLock" hinge system that provides a friction-free control surface.

The SonicModell AR Wing PRO kit is a tough, dynamic, efficient, lifting-body flying wing that delivers an impressive performance with style. The AR Wing PRO features detachable wings, so there is no glue required, which means the wings can be easily removed for transport. Other features are a large battery/flight controller bay, a nose camera bay for FPV flying that suits DJI and other cameras, and numerous compartments for the FPV transmitter (plenty of room for long-range systems) and your RC receiver, etc. These compartments have aerodynamically designed NACA air cooling systems to keep everything including your FPV gear nice and cool.

The SonicModell AR Wing Classic offers incredible performance with versatility. It features detachable wings, and wing tips that allow them to be easily removed for transport. It also has a spacious equipment bay, plus a couple of smaller bays, so there is plenty of room for your batteries, radio gear, and a variety of FPV equipment.

The Durafly Carbon Arcus is a sleek and beautiful F3A biplane designed to perform smooth, F3A-style pattern aerobatics and is the perfect choice for honing your aerobatic skills. It features a durable, lightweight EPO airframe with carbon reinforcement, aluminum landing gear, carbon interplane struts, and an advanced 4S motor and prop combination that offers a high power-to-weight ratio for unending verticals and incredible performance.

Flying the Arcus F3A is a dream, the long tail moment, the low wing loading, and the abundance of power give you a stable and predictable airplane. Take-offs require very little rudder input, rolls are crisp and axial, and loops can be as large as you wish. The large propeller provides ample braking action in the downlines to avoid overspeeding, and if you enjoy flying knife-edge, then the Arcus II performs this with ease. No roll or pitch coupling here, just apply a touch of rudder, control the throttle to hold your line, and the Arcus will knife edge until the cows come home. Finally, when the time comes, throttle back, and the Carbon Arcus settles into a nice sink rate for a perfect 3-point landing every time.

The XFLY Swift 2100 is a versatile electric-powered glider that is quite happy flying fast and doing aerobatics or is equally at home flying slowly and just floating around. To achieve this versatility the XFLY engineers have used CFD (Computer Fluid Dynamics), which has enabled the Swift 2100 to achieve a high lift-to-drag ratio and excellent aerodynamic characteristics. The factory-installed power system includes an efficient 3136-1000KV brushless motor with 40A brushless ESC and drives a 10x6 2-blade folding propeller with metal spinner. This system can be powered by either a 3S, or a 4S LiPo battery to deliver plenty of thrust for fast climbs to soaring altitudes, aerobatics, and general sport flying.

The XFLY Partenavia P68 is a small, semi-scale twin-engined model that is perfect for flying in small areas such as local parks, sports fields, etc. It has been designed to be extremely easy to fly and assemble, which makes it perfect as an entry-level choice for the novice pilot. The design is based on the full-size Partenavia P68 which is a 6-seater, twin-engined high-wing monoplane that is generally used for light transport and training.

The XFLY Partenavia P68 is a small, semi-scale twin-engined model that is perfect for flying in small areas such as local parks, sports fields, etc. It has been designed to be extremely easy to fly and assemble, which makes it perfect as an entry-level choice for the novice pilot. The design is based on the full-size Partenavia P68 which is a 6-seater, twin-engined high-wing monoplane that is generally used for light transport and training.

The Dancing Wings Hobby Stick-14T 3D aerobatic trainer is the perfect choice for intermediate and experienced RC pilots alike. It is based on the classic stick design and is quite capable of all the usual aerobatic maneuvers, plus with the right power train, it doubles up as the perfect 3D trainer. It has a very wide speed range, it is just as happy flying slowly as it is screaming about the sky. For added fun and enjoyment, the strip ailerons are split halfway making for outboard ailerons and inboard flaps. This allows for really slow or steep approach landings, and if the flaps are mixed in with your other controls it allows you to customize the handling to suit your own flying style. 

After the incredible success of the Tundra V1 and V2, Durafly has decided to produce yet another version with even more improvements to bring the Tundra series bang up to date. The V3 is now a pure 4S set-up so it has power in abundance to make your flying even more fun than it was before (if that is at all possible!). Other changes and improvements include daylight bright LEDs (so bright they are suitable for true dawn-to-dusk flying), a reinforced nylon prop that is more efficient, and better balanced, a return to the classic EPO foam wheels which are lighter, and stronger, pre-installed pushrods, and hex-head bolts and screws throughout. The V3 is available in the classic Tundra green and white scheme, or a red and silver color scheme Durafly has called the "Inspire". The reason is that the original Tundra was "Inspired" by the "Highlander" full-size SuperStol experimental airplane.