Bargain Bin

Arduino 10DOF with ITG-3205, ADXL345, HMC5883L, and BMP085

*Note: This is not an original Arduino brand product.

The Arduino Relay module allows a wide range of microcontrollers such as Arduino, AVR ,PIC, ARM with digital outputs to control larger loads and devices like AC or DC Motors, electromagnets, solenoids, and incandescent light bulbs. This relay shield uses QIANJI JQC-3F high-quality relays with rated load 7A/240VAC,10A/125VAC,10A/28VDC. The relay output state is individually indicated by a light-emitting diode.

Specs:
Dimensions: 99x70x18mm
Weight: 88g

*Note: This is not an original Arduino brand product.

Keep your Telemetry Radios safe! These cases are made out of slightly translucent ABS plastic, so you still can see TX/RX LEDs. They have a very tight fit and finish and are clearly labeled. These cases will make your setup look like Pro gear, while keeping them safe!

Designed to fit FPV Radio Telemetry Kit - 915Mhz/433MHz(#42846/42847,not included), But fits other brand Telemetry Radios as well.

Includes:
3M Foam Double-tape X1
Ground module Case X1
Air module Case X1

The flight mode switcher has been designed for open source autopilots such as APM, PX4 and Pix etc. It can switch the flight mode accurately and quickly and replaces the troublesome 2 stage and 3 stage switchers.

Users can set the parameters for the flight mode switcher on the unit and choose the most suitable modes for their requirements. The flight mode switcher features a stable performance, is easy to set up and is small and lightweight.

Typical flight modes are as follows:
• STA (Stabilized) Model will automatically level itself
• SIM (Simple) Allows you to control the movement of the model from the pilots point of view regardless of which way the model is facing
• ALT (Altitude Hold) When this mode is selected it will hold this altitude
• LOI (Loiter) Allows model to hover in the same spot on its own without any input from the pilot
• AUT (Auto) The model will follow a pre-programmed course stored in the autopilot
• RTL (Return to land) Once selected the model will return and land at the point of take-off

The flight mode switcher is simple to install on your transmitter but it is not "plug & play", there is a small amount of soldering involved inside the Tx. See under the "Files" tab for installation instructions.

Once installed on your transmitter and set up in "Mission Planner" it is very simple to use, just press the relevant mode button on the switcher and the model will go into that mode. There is an indicator light to show which mode has been selected and is in use.

Features:
• Allows the user to easily set 6 flight modes
• Simple and straightforward to install
• Compact and lightweight
• Status indicator lights

Specs:
Type: Flight Mode Switcher
Working Voltage: 3~5V
Modes: 6 selectable
Operating Temperature: -10°C~+60°C
Dimensions: 59 x 29 x 9.3mm
Weight: 13g

Included:
Flight Mode Switcher
Connection harness

Front One Way Version 2 Turnigy TD10 4WD Touring Car (1 set)

Replacement Rear Crankshaft Bearing for NGH GT35 and GT35R Gas Engines.

NGH GT25/GF38 Gas Engines Replacement Crankshaft Front Bearing

Specs:
Outlet Diameter: 26mm
Inner Diameter: 10mm
Width: 8mm
Type: Sealed

A good quality, strong, easy-to-use, iron-on plastic film covering with good shrinking properties that is suitable for most RC model airplanes.

Specs:
Material: Plastic film
Color: Small red/white chequered pattern
Adhesive: Heat-activated
Width: 638mm
Quantity: 5 meters

Please note: Parcel weight includes special tube packaging.

KingKong Multirotor Propeller 6x4 CW/CCW Green (20pcs)

Includes:
10 x 6040 Propellers (CW)
10 x 6040 Propellers (CCW)

KingKong Multirotor Propeller 6x4 CW/CCW Black (20pcs)

Includes:
10 x 6040 Propellers (CW)
10 x 6040 Propellers (CCW)

Alu. Stabilizer Holder - 1/10 Hobbyking Mission-D 4WD

Circular polarized antenna's aka "clover leaf antennas" are a great way to increase the performance of your FPV system. The circular polarization helps reject “multipath interference”, a problem that plagues standard dipole stock antennas. Proven to increase range and video clarity, circular polarized antennas have become the standard after-market 'essential' upgrade for modern FPV systems. This is a matched 3 leaf Tx to 4 leaf RX set with no cable length for a nice clean, direct install with RP-SMA connectors.

Specs:
Frequency Range: 900MHz
Impedance: 50ohm
VSWR: <1.5
Gain: 5db
Connector: RP-SMA
Cable: RG141
Cable Length: 0m

The flying V is perhaps the best general purpose antenna in the lower frequencies. Suitable for medium range and altitude, this antenna has slightly lower gain verses the coaxial connected Dipole, however has a very uniform radiation pattern. This is perfect for acrobatic and sport flying where antenna polarization (angle) can vary. The 120 deg V gives the best compromise between radiation pattern and gain.

Specs:
Frequency: 1.3GMHz
Connection: RP-SMA
dbi: 1.9

Specs.
Length: 199mm
Thickness: 3.3mm
Width: 18mm
Weight: 19g

This 2 piece carbon fiber landing gear is lightweight but very stiff and with high torsional strength, the legs are also streamlined to reduce drag. Designed for fuselages with a minimum width of 170mm, however the legs can be spaced apart to fit aircraft with a much wider fuselage. 

Specs:
Fuselage Width: 170mm
Height: 280mm
Wheel Track: 580mm
Weight: 315g

Carbon fiber tail wheel brackets add good looks, strength, and most importantly, keep excess weight out of the tail of your airplane. Made from 3K Carbon cloth, these brackets are light and strong. Comes un-drilled so it can suit a wide variety of models. Drill dimple marks are molded in for easy drilling.

Suited for models up to 80cc sized models.

Specs:
Length: 118mm
Width: 14.2mm
Weight: 7.5g

Carbon fiber tail wheel brackets add good looks, strength, and most importantly, keep excess weight out of the tail of your airplane. Made from 3K Carbon cloth, these brackets are light and strong. Comes un-drilled so it can suit a wide variety of models. Drill dimple marks are molded in for easy drilling.

Suited for models up to 120cc sized models.

Specs:
Length: 170mm
Width: 12mm
Weight: 9g

Super tough glass fiber tube, perfect for fixed wing and multi rotor projects. 

Specs:
Outer Diameter: 8mm
Bore Diameter 5mm
Length: 330mm

Aluminum alloy neck strap adjuster suitable for DJI transmitters or similar.

2mm 2 Blade CNC Folding Propeller Adapter CW & CCW (Gold)

Perfect for multi-rotors, pack comes complete with M2.5 mounting screws for the folding propeller blades.

Specs:
Suits Motor Shafts: 2mm
Blade Thickness: 3mm
Blade Mounting: M2.5
Direction: 1 x Clockwise, 1 x Counterclockwise
Material: Aluminum
Color: Gold
Weight: 6g each

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 10g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 10g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3.17mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

5 x 3 Folding Propeller Blades 1 Set CW and 1 Set CCW (Blue)

Perfect for 250 style multiracers and multicopters, each blade is manufactured from nylon and is fitted with a brass insert for strength through the blade root.

Specs:
Diameter: 5ins
Pitch: 3ins
Root Thickness: 2.4mm
Mounting Hole: 2mm
Rotation: 1 pair clockwise, 1 pair counterclockwise
Color: Blue
Weight: 0.12g each blade

8 x 4.5 Folding Propeller Blades 1 Pair CW and 1 Pair CCW (Blue)

Perfect for medium size multicopters, each blade is manufactured from nylon and is fitted with a brass insert for strength through the blade root.

Specs:
Diameter: 8ins
Pitch: 4.5ins
Root Thickness: 3mm
Mounting Hole: 3mm
Direction: 1 pair clockwise, 1 pair counterclockwise
Color: Blue
Weight: 3g each blade

8 x 4.5 Folding Propeller Blades 1 Pair CW and 1 Pair CCW (Yellow)

Perfect for medium size multicopters, each blade is manufactured from nylon and is fitted with a brass insert for strength through the blade root.

Specs:
Diameter: 8ins
Pitch: 4.5ins
Root Thickness: 3mm
Mounting Hole: 3mm
Direction: 1 pair clockwise, 1 pair counterclockwise
Color: Yellow
Weight: 3g each blade

9 x 4.7 Folding Propeller Blades 1 Pair CW and 1 Pair CCW (Green)

Perfect for medium size multicopters, each blade is manufactured from nylon and is fitted with a brass insert for strength through the blade root.

Specs:
Diameter: 9ins
Pitch: 4.7ins
Root Thickness: 3mm
Mounting Hole: 3mm
Direction: 1 pair clockwise, 1 pair counterclockwise
Color: Green
Weight: 3.4g each blade

Great performance and super value!  and thats exactly what you need for your multirotor, a tough but expendable prop that wont break the bank to replace.

Packaged as a set of 2, with one CW rotation and one CCW rotation you can afford to stock up on these great value props.

Available in 6 colors, they can be mixed and matched to help with multirotor orientation or simply give your model a unique and cool look.  

Specs:
Size:5040 (5x4)
Color: Green
Hub: 5mm
Material: Glass Reinforced Plastic/Nylon

Includes:
1 x CW rotation
1 x CCW rotation

Great performance and super value!  and thats exactly what you need for your multirotor, a tough but expendable prop that wont break the bank to replace.

Packaged as a set of 2, with one CW rotation and one CCW rotation you can afford to stock up on these great value props.

Available in 6 colors, they can be mixed and matched to help with multirotor orientation or simply give your model a unique and cool look.  

Specs:
Size:5040 (5x4)
Color: Orange
Hub: 5mm
Material: Glass Reinforced Plastic/Nylon

Includes:
1 x CW rotation
1 x CCW rotation

Slow Fly propeller.
These props come from China, however were almost certain they are made by the same mould that makes the GWS props.
Prop hub has the hex nut fitting to suit motors like the towerpro bell motors or small gearboxs with the threaded shaft.

A slow fly propeller is designed for smaller outrunner motors, typically the towerpro bell motors or slightly larger. They most suited to run on smaller planes at a lower RPM. Also great for gearbox reduced motors. A slowfly propeller typically has a spoon shaped blade.