Bargain Bin

120mm Male to Male Jumper Cable Set (10pc)

Specs: 
Length: 120mm
Pin Spacing: 1mm

Molex 2 Pin Cable Female Connector with 220mm x 26AWG Wire

Specs:
Connector: Molex 2 Pin
Colour: Black, Red
Length: 220mm

Molex 3 Cable Female Connector with 230mm x 26AWG Wire.  

Specs:
Connector:  Female Molex 3 pin
Colour: Black, Yellow, White
Length: 230mm

4mm Gold Plated Banana Plug (10pc)

HXT 4mm to T-Connector Battery Adapter Lead (2pc)

This adapter will convert an HXT 4mm equipped battery to a T-Connector for use with a T-Connector equipped ESC or Charge lead.

Spec:
Weight: 7g (Each)

This adapter will convert a 5.5mm Bullet Connector equipped battery to a T-Connector for use with a T-Connector equipped ESC or Charge lead.

Spec:
Weight: 9g(Each)

This adapter will convert a T-Connector equipped battery to an HXT 4mm for use with an HXT 4mm equipped ESC or Charge lead.

Spec:
Weight: 10g(Each)

This adapter will convert an HXT 4mm equipped battery to an XT60 for use with an XT60 equipped ESC or Charge lead.

Spec:
Weight: 10g(Each)

105mm Female Molex 1.25 to Twin Male JST-SH 1.0mm Y Lead

JR Male to 2 x JST(Molex) Female 1.00mm (1pc)

This lead converts 2 x JST(Molex) 1.00mm pitch plugged devices to 1 x JR type male plug.

Specs:
Female Plug: 2 x JST(Molex) 1.00mm pitch
Male Plug: JR type
Length Overall: 123mm
Length Each Tail: 46mm

Micro JST(Molex) 1.0mm Pitch Y Lead (1pc)

Y lead for 2 x micro JST(Molex) plugged servo's or ESC.

Specs:
Male Plug: 2 x JST(Molex) 1.00mm pitch
Female Plug: 1 x JST(Molex) 1.00mm pitch
Length Overall: 105mm
Length Each Tail: 43mm

Mini black T Connector pack (5 Pairs)

Specs:
Base Dimensions: 5mm x 8mm
Contact Dimension: 3mm x 5mm x 1mm
Rating: 10amps continuous

Super flexible 26AWG twisted silicone male to male servo lead. These are specifically made as signal leads for RX to Flight controller connections, the light 26AWG silicone wire is so flexible it transfers virtually no vibration to the Flight controller, well the twist helps reduce inducted noise. If used in conjunction of having only one lead vertical and the other leads turned on their side for signal only, makes for a clean and minimal vibration transfer installation. Or better yet a single CPPM/SBUS single lead. 

Specs:
Length: 130mm(black/red/white)
Connection: Male JR style plug on each end.

Super flexible 26AWG twisted silicone male to male servo lead. These are specifically made as signal leads for RX to Flight controller connections, the light 26AWG silicone wire is so flexible it transfers virtually no vibration to the Flight controller, well the twist helps reduce inducted noise. If used in conjunction of having only one lead vertical and the leads turned on their side for signal only makes for a clean and minimal vibration transfer installation, or better yet a single CPPM/SBUS single lead.

Specs:
Length: 80mm(black/red/white)
Connection: Male JR style plug on each end.

T-Connector to EC5 Battery Adapter (2pcs/bag)

This adapter will convert a T-Connector equipped battery to a EC5 Plug for use with a EC5 equipped ESC or an EC5 Charge lead.

T-Connector to HXT4mm Battery Adapter (2pcs/bag)

This adapter will convert a T-Connector equipped battery to a HXT4mm for use with a HXT4mm equipped ESC or an HXT4mm Charge lead.

Mini Tamiya to T-Connector Battery Adapter (2pcs/bag)

This adapter will convert a Mini Tamiya equipped battery to a T-Connector for use with a T-Connector equipped ESC or a T-Connector Charge lead.

A handy adapter to convert an XT60 equipped battery to an MPX style connector. Useful for use with MPX equipped ESC or Charge leads.

Spec:
Weight: 5.3g(Each)

HXT 4mm bullet to XT90 Battery Adapter (2pcs)

This adapter will convert a 4mm bullet equipped battery to a XT90 for use with a XT90 equipped ESC or a XT90 Charge lead.

XT90 to 4.0mm bullet Battery Adapter (2pcs/bag)

This adapter will convert a XT90 equipped battery to a 4.0mm bullet for use with a 4.0mm bullet equipped ESC or a 4.0mm bullet Charge lead.

HXT3.5mm to XT60 Battery Adapter (2pcs/bag)

This adapter will convert a HXT3.5mm equipped battery to a XT60 for use with a XT60 equipped ESC or a XT60 Charge lead.

This data cable allows you to connect our 433/915MHz V1.1 Radio Telemetry Kits to your Walkera X800 GPS Quadcopter. The X800 flight controller has a data port which actually functions as a standard APM UART connection. The port is a specialized 4-pin connector which will not fit standard Molex style plugs.

This data cable will allow you to plug directly to the X800 FC data port and to our 433/915MHz V1.1 Radio Telemetry air module, allowing full access to wireless telemetry functionality of the APM based X800 flight controller.

Specs:
Connection: 4-pin Walkera style plug to 6-pin Molex style plug
Length: 180mm

*Note: Please see related items below for the compatible 433/915MHz V1.1 Radio Telemetry Kits.

A JST male plug to 2.54mm pitch male jumper lead for a variety of uses.

This lead is the best solution for batteries that are slightly out of balance; simply plug it into the individual cells on the balance lead, select a 1S charge rate and you can charge them one at a time to ensure they are all at optimum charge. 

Only use this method to restore cells that are slightly out of balance and remember that there could be something wrong with one of the cells so keep a close eye on it while charging.

Overall length: 70mm

Specs:
Model: TGY-225MG
Voltage: 4.5 - 6v
Speed: .12s
Running Current: 180mA
Torque: 3.5kg/cm
Gears: Metal
Weight: 26g
Spline Count : 21 Tooth

Narrow dead band width.

The ImmersionRC 5v - 12v Step Up Converter provides power to drive 12v cameras from the 5v outputs of ImmersionRC's A/V transmitters.

The highly efficient step-up regulator, has almost zero RF emissions and with a 250mA maximum output current, the converter can power most of the commonly used FPV cameras. The step up converter is super lightweight and compact weighing in at just 2g.

Features:
• Converts 5V to 12v to power a multitude of FPV cameras
• 90% efficiency
• Super lightweight and compact (the size of a regular postage stamp)
• Minimal RF emissions

Specs:
Weight: 2g
Dimensions: 28 x 13 x 3mm
Material: PCB

The Vortex FPV Racer from ImmersionRC is an incredible piece of kit for the serious competitor, but like all things flying the ocassional mishap is inevitable!

This crash kit is a convenient way to keep a stock of all of those plastic parts most likely to be damaged in a serious "departure from controlled flight"

Included are all parts which mount the motors to the carbon fiber arms, the plastic pivot points, foldable arm clips, and all other plastic parts.

No carbon fiber parts are included (see Crash Kit 2.)

Included:
1 x Front bumper (FR4)
2 x Side plates
8 x Arm clips
4 x Arm pivot tops
4 x Arm pivot bottoms
4 x Landing bumpers
4 x Landing mounts
4 x Motor mounts
8 x Hex bushes
1 x Camera support base
1 x Camera support arm
4 x Damper pins
4x Damper circlip
4x Screw HA2x8
4x Screw HA2x6

22mm 280 C-Shape Motor Mount (clamp style)

Spec.
Diameter: 22mm (Fits 280 Size Inrunner)
Length: 31.5mm
Weight: 9g

This handy little device allows you to program your ZYX Flybarless Controller wirelessly via Bluetooth connectivity with your Android device. Now there is no longer a need to bring your PC to the field for making programming adjustments!

Simply plug this device into the data port of your ZYX unit, install the free ZYX programming app on your Android mobile device and you are all set! It's that easy. You will be able to access all of the same programming options that are available on the PC software directly from your Android device.

This is a must have for any ZYX user with an Android mobile device!

Features:
• Compact size
• Easy to use
• Bluetooth wireless connectivity
• Free Android app available
• Eliminates the need to bring your PC to the field

Specs:
Dimensions: 32x14x5mm
Weight: 3g

*Note: This device currently supports Android 1.6 and above versions of the operating system.

Tarot 450 Pro/Pro V2 DFC Feathering Spindle (TL48016)

The Tarot 450 Pro/Pro V2 DFC feathering spindles are uniquely designed to reduce the probability of the retaining screws coming loose.

Includes:
450 DFC Feathering Spindle x 1 (4x54mm)
Thrust Bearing x 2 (4x8x3.5mm)
Thrust Bearing Circlip x 2 (M4x6.5x1.5mm)
M2.5 Socket Head Screws x 2 (M2.5x6mm)
Washers x 2 (4x7.5x1mm)

Telemicro 520mm - Replacement Spinner

Hobbyking Bixler 2 EPO 1500mm - Replacement Pushrod Set

HobbyKing Bixler 2 EPO 1500mm -  Replacement Flap Hinges (6pcs/bag)

Works for both Bixler 2 and Bix3 models.

This is a great way to avoid power shorts.

Gold connectors on their own are notorious for creating a short circuit and looking messy. Use these to keep your connections safe and looking neat!

Rated to 20Amp these connectors are an excellent replacement for JST plugs on todays small yet high C rated batteries.

JR to EH Adapter wire (2pcs/bag)