Workbench

Remember the last time you were at the field and needed to make a quick repair to your foamy? This handy battery powered hot glue gun would have been just the tool for the job.

Operating on 12VDC, this glue gun can be powered by any standard 3S lipoly battery. It comes pre-fitted with an XT60 plug allowing you to easily connect to your Turnigy/Zippy lipoly battery. Everyone has a 3S 2200mAh battery in their field box, so you'll always have power for your hot glue gun. This tool is a must have for any flight box!

*Note: This glue gun does not feature a low voltage cutoff circuit, so we recommend using a low voltage battery alarm to monitor the input battery to avoid over-discharging. Please see related items below.

Specs:
Operating Voltage: 12VDC
Power: 10W
Power Plug: XT60

The Pro Mini is a microcontroller board based on the ATmega328. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, an on-board resonator, a reset button, and holes for mounting pin headers. A six pin header can be connected to an FTDI cable or breakout board to provide USB power and communication to the board.
 
The Pro Mini is intended for semi-permanent installation in objects or exhibitions. The board comes without pre-mounted headers, allowing the use of various types of connectors or direct soldering of wires. The pin layout is compatible with the Arduino Mini.

Mini USB Adapter (included):
This board converts a USB connection into 5 volt TX and RX signals that you can connect straight to the Arduino Mini or other microcontrollers, allowing them to talk to the computer. It is based on the FT232RL chip from FTDI (drivers are included with the Arduino software).

Features:
• ATmega328 running at 8MHz with external resonator (0.5% tolerance)
• USB connection off board
• Supports auto-reset
• 3.3V regulator
• Max 150mA output
• Over current protected
• Reverse polarity protected
• DC input 3.3V up to 12V
• On board Power and Status LEDs

Specs:
Operating Voltage: 3.3V
Input Voltage: 3.35 -12V
Digital I/O Pins: 14 (of which 6 provide PWM output)
Analog Input Pins: 6
DC Current per I/O Pin: 40mA
Flash Memory: 16KB (of which 2 KB used by bootloader)
SRAM: 1KB
EEPROM: 512 bytes
Clock Speed:  8MHz
Dimensions: 18x33mm
Weight: 2.3g

Includes:
1 x Pro Mini Microcontroller
1 x Mini USB Adapter

*Note: This is not an original Arduino brand product.

USBtinyISP V2.0 (Arduino-Compatible) is an ISP downloader for AVR microcontrollers based on the USB interface. It can be used for most AVR microcontrollers to download programs. In Arduino IDE, USBtinyISP is a downloader that is supported at all times, making it simple and convenient to use.

Specs:
Dimensions: 49x48x12mm
Weight: 17.3g

*Note: This is not an original Arduino brand product.

This is a great “bread board” pin ready accelerometer for your Arduino or other microcontroller projects

Features:
• BMA180 three-axis ultra-high performance digital accelerometer, which provides a 14-bit digital output via a 4-wire SPI or 2-wire I 2 C interface
• Full scale measurement range can be set to ± 1g balance, 1.5G, 2G, 3G, 4G, 8G or 16G
• programmable wake-up
• Low-g and high-g detection
• Tap detection
• Slope detection
• Self-test capability
• The sensor also has two operating modes: low noise, low power consumption in a tiny 3x3mm 12-pin LGA package BMA180
• The sensor can be between 1.62 to 3.6V VDD and 1.2 to 3.6V VDDIO supply will typically only consume 650uA standard mode.

Specs:
Size: 21 x 10 x 2.6mm
Voltage: 1.2-3.6v
Output: SPI or I2C

*Note: This is not an original Arduino brand product.

Superheterodyne 3310 Wireless receiver module +315RF Wireless transmitter module 

The Kingduino Pro 328 is a 5V/16MHz board running the 16MHz bootloader in a miniature form factor that will fit easily into your next small project.

The Pro 328 does not come with connectors, allowing you to solder in any connector or wire in any orientation required and is recommended for users who understand the limitations of this lack of connectors and USB off board.

The compact size is helped by having the DC power jack footprint available, but without hardware attached. This allows you to decide how best to utilize this function.

This board connects directly to the FTDI Basic Breakout board and supports auto-reset. The Kingduino Pro 328 also works with the FTDI cable but the FTDI cable does not bring out the DTR pin so the auto-reset feature will not work. In this latest version of the Kingduino Pro we’ve also moved the FTDI headers back so that the pins don’t hang over the edge of the board. We’ve also populated it with a sturdier power selection switch.

Features:
• USB connection off board
• 5V regulator
• Over current protected
• Reverse polarity protected
• DC input
• Resettable fuse prevents damage to board in case of short
• Power select switch acts as on/off switch

Specs:
Microcontroller: ATmega328
Clock Speed: 16MHz
Input Voltage: 5 ~ 12V DC
Max output: 150mA
Dimensions: 54 x 52mm

*Note: This is not an original Arduino brand product.

Arduino MEGA ProtoShield V3 prototype expansion board (including the bread board)

This is the latest Arduino MEGA ProtoShield V3 prototype expansion board with Immersion Gold PCB processing technology. The motherboard gold square pad spacing is small and features SOP28 SMD component packaging, perfect for Arduino electronics enthusiasts. 

This board can not only seamlessly be plugged into the Arduino MEGA controller, components can be soldered directly. To complete a variety of circuits, this board features an integrated power indicator, status lights and reset buttons.

Specs:
Dimensions: 103x56x19mm
Weight: 39.7g (w/bread board)

*Note: This is not an original Arduino brand product.

The LM35 Linear Temperature Sensor Module can be used to detect ambient air temperature. This sensor offers a functional range between -40 degree Celsius to 150 degree Celsius. Sensitivity is 10mV per degree Celsius. The output voltage is proportional to the temperature. It is commonly used as a temperature measurement sensor. It includes thermocouples, platinum resistance, thermal resistance and temperature semiconductor chips, which are commonly used in high temperature measurement thermocouples. Platinum resistance temperature used in the measurement of 800 degrees Celsius, while the thermal resistance and semiconductor temperature sensor suitable for measuring the temperature of 100-200 degrees or below, in which the application of a simple semiconductor temperature sensor has good linearity and high sensitivity. The LM35 linear temperature sensor and sensor-specific expansion of Arduino board, in combination, can be very easy to achieve.

Specs:
Sensitivity: 10mV per degree
Celcius Functional range: -40 degree Celsius to 150 degree Celsius

*Note: This is not an original Arduino brand product.

Arduino 6-DOF IMU Module Attitude Control 6DOF 3205 345

*Note: This is not an original Arduino brand product.

Arduino 10DOF with ITG-3205, ADXL345, HMC5883L, and BMP085

*Note: This is not an original Arduino brand product.

The Arduino Relay module allows a wide range of microcontrollers such as Arduino, AVR ,PIC, ARM with digital outputs to control larger loads and devices like AC or DC Motors, electromagnets, solenoids, and incandescent light bulbs. This relay shield uses QIANJI JQC-3F high-quality relays with rated load 7A/240VAC,10A/125VAC,10A/28VDC. The relay output state is individually indicated by a light-emitting diode.

Specs:
Dimensions: 99x70x18mm
Weight: 88g

*Note: This is not an original Arduino brand product.

USBasp AVR Programming Device for ATMEL Processors

Includes:
1 x USBasp Device
1 x Cable

Suits the HobbyKing Quadcopter Control Board.

Keep your Telemetry Radios safe! These cases are made out of slightly translucent ABS plastic, so you still can see TX/RX LEDs. They have a very tight fit and finish and are clearly labeled. These cases will make your setup look like Pro gear, while keeping them safe!

Designed to fit FPV Radio Telemetry Kit - 915Mhz/433MHz(#42846/42847,not included), But fits other brand Telemetry Radios as well.

Includes:
3M Foam Double-tape X1
Ground module Case X1
Air module Case X1

Good quality iron-on heatshrink covering film in solid turquoise blue.

Dimensions:
638mm x 5m

Please note: Due to supply issues, this covering film is limited to a maximum purchase quantity of 5 per order.

Good quality iron-on heatshrink covering film in solid metallic gold color finish.

Dimensions:
638mm x 5m

Carmine 101 - 5m solid color iron-on covering shrink film.
638mm wide. 

Please note: Due to supply issues, this covering film is limited to a maximum purchase quantity of 5 per order.

*Parcel weight includes special tube packaging.

Bright Red 102 - 5m solid color iron-on covering shrink film.
638mm wide.

Please note: Due to supply issues, this covering film is limited to a maximum purchase quantity of 5 per order.

*Parcel weight includes special tube packaging.

Mid-Yellow 104 - 5m solid color iron-on covering shrink film.
638mm wide.

Please note: Due to supply issues, this covering film is limited to a maximum purchase quantity of 5 per order.

*Parcel weight includes special tube packaging.

Cyan-Yellow 105 - 5m Solid Colour iron-on covering shrink film.
638mm Wide.

Please note: Due to supply issues, this covering film is limited to a maximum purchase quantity of 5 per order.

*Parcel weight includes special tube packaging.

Amber 106 - 5m Solid Colour iron-on covering shrink film.
638mm Wide.

Please note: Due to supply issues, this covering film is limited to a maximum purchase quantity of 5 per order.

*Parcel weight includes special tube packaging.

Sea-Blue 108 - 5m Solid Colour iron-on covering shrink film.
638mm Wide.

Please note: Due to supply issues, this covering film is limited to a maximum purchase quantity of 5 per order.

*Parcel weight includes special tube packaging.

Blue-Black 102 - 5m solid color iron-on covering shrink film.
638mm wide.

Please note: Due to supply issues, this covering film is limited to a maximum purchase quantity of 5 per order.

*Parcel weight includes special tube packaging.

Grass Green 110 - 5m solid color iron on covering shrink film
638mm wide


*Parcel weight includes special tube packaging.

Olive Green 112 - 5m solid color iron on covering shrink film
638mm wide


*Parcel weight includes special tube packaging.

Solid White 113 - 5m solid color iron-on covering shrink film
638mm wide.

Please note: Due to supply issues, this covering film is limited to a maximum purchase quantity of 5 per order.

*Parcel weight includes special tube packaging.

Solid Black 114 - 5m solid color iron-on covering shrink film
638mm wide.

Please note: Due to supply issues, this covering film is limited to a maximum purchase quantity of 5 per order.

*Parcel weight includes special tube packaging.

Solid Silver 115 - 5m solid color iron-on covering shrink film
638mm wide.

Please note: Due to supply issues, this covering film is limited to a maximum purchase quantity of 5 per order.

*Parcel weight includes special tube packaging.

Solid Light-Gray - 5m solid color iron on covering shrink film
638mm wide


*Parcel weight includes special tube packaging.

Solid Jacinth 118 - 5m solid color iron on covering shrink film
638mm wide


*Parcel weight includes special tube packaging.

A good quality, strong, easy-to-use, iron-on plastic film covering with good shrinking properties that is suitable for most RC model airplanes.

Specs:
Material: Plastic film
Color: Small red/white chequered pattern
Adhesive: Heat-activated
Width: 638mm
Quantity: 5 meters

Please note: Parcel weight includes special tube packaging.

Black/White chequer - 5m solid color iron-on covering shrink film
638mm wide.

Please note: Due to supply issues, this covering film is limited to a maximum purchase quantity of 5 per order.

*Parcel weight includes special tube packaging.

Bright Silver 406 - 5m solid color iron-on covering shrink film
638mm wide.

Please note: Due to supply issues, this covering film is limited to a maximum purchase quantity of 5 per order.

*Parcel weight includes special tube packaging.

Transparent Red 201 - 5m solid color iron on covering shrink film
638mm wide


*Parcel weight includes special tube packaging.

Transparent Burnt Orange 202 - 5m solid color iron on covering shrink film
638mm wide


*Parcel weight includes special tube packaging.

Transparent Yellow 203 - 5m solid color iron on covering shrink film
638mm wide


*Parcel weight includes special tube packaging.