Corona 939MG Metal Gear Servo 2.5kg / 0.14sec / 12.5g

Corona DS329MG Digital Metal Gear Servo 3.8kg / 0.11sec / 32g

Corona DS339MG Digital Metal Gear Servo 4.4kg / 0.15sec / 32g

Corona 919MG Metal Gear Servo 1.7kg/ 0.06sec / 12.5g

Micro analog servo.
Precise, jitter free response for small parkflyers or light 3D.

The easiest way to put retracts in your plane. No need to install a control box, messy wiring or a complicated air system. Just screw in the retracts, connect to your Rx and youre ready!

Reliable servoless mechanism with metal gearing and a high torque motor ensures trouble free flying! This unit comes with 2 mount plates meaning it can be mounted normally or reverse with the extra plate being used for a top wing re-enforcing plate if required.

Why bother with air systems when you can now have a realistic and reliable electric unit at a fraction of the price?!

Spec.
Working voltage: 4.8~6V
Speed: 0.55s/60deg 4.8v - 0.45s/60deg 6v
Travel: 90 degree
Dimensions: 54.8x32x21mm
Weight: 18.8g
Shaft size: 3mm

Mount Dimensions:
Mounting Plate Dimensions: 32mmx25mm
Hole Spacing: 17mmx25mm

Not suitable for a plane heavier than 2kg
Strut & Landing gear not included

HobbyKing 2.4Ghz 4Ch Tx & Rx V2 (Mode 2)(THROTTLE ON THE LEFT)

Don't let the price fool you. This is a decent analog servo and the colour is, well, different.
No longer will you goose step to the blue or black servo crowd, get a HobbyKing HK15178!

Spec:
Torque: 1.2kg/cm @ 4.8v, 1.4kg/cm @ 6v
Weight: 10g
Speed: 0.10/60deg @ 4.8v, 0.09/60deg @ 6v
Voltage: 4.8v~6v
Plug: JR

HobbyKing 939MG Metal Gear Servo 2.5kg/ 0.14sec / 12.5g
A strong performer with a very smooth movement and good centering.
Excellent for parkflyers or planes up to .40 size (3,500mAh electric).

The Turnigy D56MG HV is great for small 3D planes and parkflyers where the ruggedness of a metal gear train is required. The coreless motor provides excellent holding power and precision at a great price. The HV voltage lets you use a 2s Lipo or LiFE battery directly with no need for a BEC.

The Turnigy D56LV is great for small gliders and DLGs, or just about any other mini airplane using single cell LiPoly batteries (3.7V) and where the ruggedness of a metal gear train is required. The coreless motor provides excellent holding power and precision at a great price.

Protect your OrangeRx receiver from damage and vibration with this protective silicone shell.Fits snuggly around most of the non satellite receivers and it has exit holes on the rear and side for the antennas.

Specs:
Length: 44.5mm
Width: 25mm
Height: 16mm
Weight: 6g

Protect your Orange receivers from fuel or crash damage with the Orange RX Silicone Rubber
Shell. The shell provides added protection for the heart of your RC model whilst also providing
additional securing options. The rear of the shell has a slot to allow the use of hook and loop securing straps, additional slots are provided for the antenna and satellite port of your receiver.

Specs:
Suitable Receiver: Orange R620
Material: Silicone rubber
Color: Black
Dimensions: 46 x 25 x 17mm
Weight: 4.4g

Protect your OrangeRx receiver from damage and vibration with this protective silicone shell.Fits snuggly around most of the satellite receivers and it has an exit hole on the rear for the antenna and a cut-out on the side for the satellite receiver plug.

Specs:
Length: 47.5mm
Width: 25mm
Height: 16mm
Weight: 8g

Protect your Orange receivers from fuel or crash damage with the Orange RX Silicone Rubber
Shell. The shell provides added protection for the heart of your RC model whilst also providing
additional securing options. The rear of the shell has a slot to allow the use of hook and loop
securing straps, additional slots are provided for the twin antenna.

Specs:
Suitable Receiver: Orange R615
Material: Silicone rubber
Color: Black
Dimensions: 46 x 22 x 15mm
Weight: 3.5g

Protect your Orange receivers from fuel or crash damage with the Orange RX Silicone Rubber
Shell. The shell provides added protection for the heart of your RC model whilst also providing
additional securing options. The rear of the shell has a slot to allow the use of hook and loop
securing straps, additional slots are provided for the twin antenna.

Specs:
Suitable Receiver: Orange R620
Material: Silicone rubber
Color: Black
Dimensions: 43 x 25 x 16mm
Weight: 5g

Turnigy analog micro servo offering good torque, high speed, excellent centering and a great price!

The strong gear train is all metal geared.

Specs:
Weight: 9g
Size: 23.1mmx12.0mmx25.9mm
Torque: 1.6kg.cm (4.8v)2 kg.cm (6.0v)
Speed: 0.08 sec/60deg (4.8v)0.07 sec/deg (6.0v) 
Voltage: 4.8-6.0v
Type: Analog Micro
Gear Train: Metal
Ball Bearing: No
Lead Length: 240mm
Plug: JR/Futaba
Spline Count: 20

Looking for solid, high torque servos for your 1/5th scale car, truck or buggy? The Trackstar TS-500HD servos are just the ticket! The servos have a torque range of 27.3 - 32kg whilst still maintaining good operating speeds across its 4.8 - 7.4v input range. The servo's temperature is maintained by its beautifully machined heat sink housing which has a cool red anodized finish.

The Trackstar TS500HD servos are an excellent choice for everday bashing and can even handle the toughest of off-road tracks in almost any race conditions!

Servos are supplied complete with control horns and all necessary fixtures and fittings.
  
Specs:
Operating Voltage: 4.8 ~ 7.4v
Weight: 188g
Dimensions: 68 x 60 x 30 mm
Torque: 27.3kg (4.8v) 30.5kg (6.0v) 32kg (7.4v) 
Speed: 0.22sec/60deg (4.8v) 0.20sec/60deg (6.0v) 0.19 sec/60deg (7.4v)
Motor: Brushed DC motor 
Gear Train: Metal
Spline Count: 17

If you're looking for the ultimate steering servo for your 1/10th touring, drift car or buggy, we have just the thing!

The TrackStar TS-D99X is a standard size low profile digital servo featuring a titianium geartrain, coreless motor and a fast 0.08sec transit time. Add to that it's excellent performance and tricked out looks, and you have one outstanding steering servo for the price!

Specs:
Weight: 45g
Size: 40mmx20mmx25.5mm
Torque: 8kg.cm (4.8V)~10kg.cm (6.0V)
Speed: 0.09 sec/60deg (4.8V)~0.08 sec/60deg (6.0V)
Voltage: 4.8V~6.0V
Type: Digital Standard
Gear Train: Titanium
Ball Bearing: Dual BB
Servo teeth: 25T
Lead Length: 285mm
Plug: JR/Futaba

The Turnigy TG9d is the new standard in low cost digital servos in the 9 gram class. Boasting the holding power and precision of digital, something needed for your small, high performance park flyers. We include a selection of servo arms to work with most applications. With a price tag that rivals cheaper analog servos, the TG9d is a awesome upgrade that won't beak the bank.

Features:
• Plastic Bushing
• Heavy Duty Output Spline
• Servo arms & screw included
• Perfect for high performance parkflyers

Specs:
Size : 22.4x12.5x23mm 
Voltage : 4.8v~6v
Weight: 9g / 0.39oz
Speed : 0.10 sec/60 (4.8V)0.09 sec/60 (6.0V)
Torque : 1.6kg-cm (4.8V)1.8kg-cm (6.0V)
Working Temp : -30C~60C 
Gears: Nylon White type
Spline Count: 21

If you're looking for the ultimate steering servo for your 1/12th pan car, we have just the thing!

The TrackStar TS-P12S is a mini size high speed digital servo featuring a titianium geartrain, coreless motor and a fast 0.05sec transit time. Add to that it's excellent performance and tricked out looks, and you have one outstanding steering servo for the price!

Specs:
Weight: 28g
Size: 36mmx15mmx29mm
Torque: 2.8 kg.cm (4.8V)~3.6 kg.cm (6.0V)
Speed: 0.06 sec/60deg (4.8V)~0.05 sec/60deg (6.0V)
Voltage: 4.8V~6.0V
Type: Digital Standard
Gear Train: Titanium
Ball Bearing: Dual BB
Servo teeth: 25T
Lead Length: 285mm
Plug: JR/Futaba

Turnigy TGY-AN13 analog car servo suitable for 1:8 & 1:10 scale cars with a tough, metal geartrain.

Supplied with a full hardware pack.

Specs:
Torque: 13.2kg/cm (4.8V)~14.5kg/cm (6.0V)
Speed: 0.15sec/60deg (4.8V)~0.13sec/60deg (6.0V)
Voltage: 4.8~6.0V
Type: Analog
Gear Train: Metal
Plug: JR type
Size: 40 x 37.5 x 20mm
Weight: 58g
Spline Count: 25