$0.01 - $0.99

Screw Countersunk Phillips M2.5x12mm (10pcs/pack)

Most standard 7S lithium polymer battery packs feature two balance ports, a 4S and 3S balance lead (total 7S). This makes it difficult to charge with most standard battery chargers that only feature one balance port.

With this super useful adapter you can easily charge your 7S battery with any standard 8~10S capable balance charger that accepts JST-XH balance plugs. This adapter takes the 4S and 3S individual plugs from your pack, and combines them to one single 7S balance plug which is able to connect to most standard 8~10S capable chargers.

Specs:
Input: 1 x 4S and 1 x 3S JST-XH balance plug
Output: 7S JST-XH balance plug
Length: 100mm

Manifold 1set(nickel plating) - A3007

A quick and easy way to eliminate a built in BEC without the need to cut or modify your ESC wires.

Futaba 6pin Trainer Port Plug to JR Male Servo plug (1pcs/bag)

EC2 Male - ESC Connector (5pcs/bag)

EC2 Female & Male (5pcs/bag)

T-Connector Harness for 2 Packs in Parallel (1pc)

Spec:
Weight: 9.0g

JST-XH to JST LED Power Distribution Lead - A neat way to power LED's from 3s Lipoly's using the balance plug.



** WARNING: Check Polarity of your setup before connecting this harness.

This handy connector set will be appreciated by anyone who is dealing with 'Header Pins' on Multirotor boards or any othe type of PCB.

This set consists of a 1 pin housing and 1 female terminal.

120mm Male to Male Jumper Cable Set (10pc)

Specs: 
Length: 120mm
Pin Spacing: 1mm

Molex 2 Pin Cable Female Connector with 220mm x 26AWG Wire

Specs:
Connector: Molex 2 Pin
Colour: Black, Red
Length: 220mm

Molex 3 Cable Female Connector with 230mm x 26AWG Wire.  

Specs:
Connector:  Female Molex 3 pin
Colour: Black, Yellow, White
Length: 230mm

HXT 4mm to T-Connector Battery Adapter Lead (2pc)

This adapter will convert an HXT 4mm equipped battery to a T-Connector for use with a T-Connector equipped ESC or Charge lead.

Spec:
Weight: 7g (Each)

This adapter will convert a T-Connector equipped battery to an HXT 4mm for use with an HXT 4mm equipped ESC or Charge lead.

Spec:
Weight: 10g(Each)

This adapter will convert an HXT 4mm equipped battery to an XT60 for use with an XT60 equipped ESC or Charge lead.

Spec:
Weight: 10g(Each)

105mm Female Molex 1.25 to Twin Male JST-SH 1.0mm Y Lead

JR Male to 2 x JST(Molex) Female 1.00mm (1pc)

This lead converts 2 x JST(Molex) 1.00mm pitch plugged devices to 1 x JR type male plug.

Specs:
Female Plug: 2 x JST(Molex) 1.00mm pitch
Male Plug: JR type
Length Overall: 123mm
Length Each Tail: 46mm

Micro JST(Molex) 1.0mm Pitch Y Lead (1pc)

Y lead for 2 x micro JST(Molex) plugged servo's or ESC.

Specs:
Male Plug: 2 x JST(Molex) 1.00mm pitch
Female Plug: 1 x JST(Molex) 1.00mm pitch
Length Overall: 105mm
Length Each Tail: 43mm

T-Connector to EC5 Battery Adapter (2pcs/bag)

This adapter will convert a T-Connector equipped battery to a EC5 Plug for use with a EC5 equipped ESC or an EC5 Charge lead.

T-Connector to HXT4mm Battery Adapter (2pcs/bag)

This adapter will convert a T-Connector equipped battery to a HXT4mm for use with a HXT4mm equipped ESC or an HXT4mm Charge lead.

HXT3.5mm to XT60 Battery Adapter (2pcs/bag)

This adapter will convert a HXT3.5mm equipped battery to a XT60 for use with a XT60 equipped ESC or a XT60 Charge lead.

This data cable allows you to connect our 433/915MHz V1.1 Radio Telemetry Kits to your Walkera X800 GPS Quadcopter. The X800 flight controller has a data port which actually functions as a standard APM UART connection. The port is a specialized 4-pin connector which will not fit standard Molex style plugs.

This data cable will allow you to plug directly to the X800 FC data port and to our 433/915MHz V1.1 Radio Telemetry air module, allowing full access to wireless telemetry functionality of the APM based X800 flight controller.

Specs:
Connection: 4-pin Walkera style plug to 6-pin Molex style plug
Length: 180mm

*Note: Please see related items below for the compatible 433/915MHz V1.1 Radio Telemetry Kits.

A JST male plug to 2.54mm pitch male jumper lead for a variety of uses.

This lead is the best solution for batteries that are slightly out of balance; simply plug it into the individual cells on the balance lead, select a 1S charge rate and you can charge them one at a time to ensure they are all at optimum charge. 

Only use this method to restore cells that are slightly out of balance and remember that there could be something wrong with one of the cells so keep a close eye on it while charging.

Overall length: 70mm

The Vortex FPV Racer from ImmersionRC is an incredible piece of kit for the serious competitor, but like all things flying the ocassional mishap is inevitable!

This crash kit is a convenient way to keep a stock of all of those plastic parts most likely to be damaged in a serious "departure from controlled flight"

Included are all parts which mount the motors to the carbon fiber arms, the plastic pivot points, foldable arm clips, and all other plastic parts.

No carbon fiber parts are included (see Crash Kit 2.)

Included:
1 x Front bumper (FR4)
2 x Side plates
8 x Arm clips
4 x Arm pivot tops
4 x Arm pivot bottoms
4 x Landing bumpers
4 x Landing mounts
4 x Motor mounts
8 x Hex bushes
1 x Camera support base
1 x Camera support arm
4 x Damper pins
4x Damper circlip
4x Screw HA2x8
4x Screw HA2x6

22mm 280 C-Shape Motor Mount (clamp style)

Spec.
Diameter: 22mm (Fits 280 Size Inrunner)
Length: 31.5mm
Weight: 9g

Tarot 450 Pro/Pro V2 DFC Feathering Spindle (TL48016)

The Tarot 450 Pro/Pro V2 DFC feathering spindles are uniquely designed to reduce the probability of the retaining screws coming loose.

Includes:
450 DFC Feathering Spindle x 1 (4x54mm)
Thrust Bearing x 2 (4x8x3.5mm)
Thrust Bearing Circlip x 2 (M4x6.5x1.5mm)
M2.5 Socket Head Screws x 2 (M2.5x6mm)
Washers x 2 (4x7.5x1mm)

Telemicro 520mm - Replacement Spinner

HobbyKing Bixler 2 EPO 1500mm -  Replacement Flap Hinges (6pcs/bag)

Works for both Bixler 2 and Bix3 models.

This is a great way to avoid power shorts.

Gold connectors on their own are notorious for creating a short circuit and looking messy. Use these to keep your connections safe and looking neat!

Rated to 20Amp these connectors are an excellent replacement for JST plugs on todays small yet high C rated batteries.

JR to EH Adapter wire (2pcs/bag)

Solo Pro FP II Main Rotor Blade Set