Bargain Bin

This simple and effective charge lead comes pre-soldered with standard 4mm bullet connectors at the charger end and has stepped, bullet connectors at the battery end allowing you to charge hard case packs that utilise 4mm and 5mm connectors. 

Front Sway Bar Set (silver/blue/black) - Basher SaberTooth 1/8 Scale Truggy / Nitro  Circus MT 

Rear sway bar set (silver/blue/black) - Basher SaberTooth 1/8 Scale Truggy

Make the most of your RC boat with this powerful ESC. Designed with a high performance MCU, the circuit design ensures strong anti-interference and intelligent technology. The waterproof design features fast throttle response, smooth speed control linearity, and programmable start mode.

Program your Turnigy Marine ESCs with this high-quality program card. Easy to use, this handy program card covers all your basic features and more. Select your Running Mode to ensure your ESCs operate forwards or backwards. The program card also allows you to choose your motor direction, low voltage protection threshold, timing set and start mode.

These are Micro Engineerings HO/N scale Code 70 to 55 slide on plastic insulating rail joiners. These insulating joiners are perfect for where you want to electrically isolate sections of track when transitioning from Code 70 to Code 55 rail.

The Micro Engineering's rail weathering solution is used to weather nickel silver or brass track and track joiners etc so that they match their weathered Flex-Trak.

The Micro Engineering's rail weathering solution is used to weather nickel silver or brass track and track joiners etc so that they match their weathered Flex-Trak.

Micro Engineering produces a range of building structure components to allow you to construct your own scratch built buildings. These are double baggage doors that are suitable for warehouses and other storage lineside buildings etc.

Micro Engineering produces a range of building structure components to allow you to construct your own scratch built buildings. These office windows/doors are typical of the style used in office blocks around the world. They have many other uses as well so can be used in a variety of buildings that may appear on a model railway.

Micro Engineering produces a range of building structure components to allow you to construct your own scratch built buildings. This is a selection of typical roof vents and fans that you would see on buildings all around the world. Add that bit of realism to your scratch built buildings with these protypical fittings.

Micro Engineering produces a range of building structure components to allow you to construct your own scratch built buildings. Around railway, industrial buildings and garage scenes there always old car tires hanging around cluttering up the place . Add that little bit of realism to your model railway layout with these very effective tire stacks and loose tires.

The Micro Engineering N scale turnout parts includes a cast metal frog with a rib along the bottom, 2 x rail guards and a switch assembly made up of 2 switch rails with molded plastic throwbar.

The Micro Engineering N scale turnout parts includes a cast metal frog with a rib along the bottom, 2 x rail guards and a switch assembly made up of 2 switch rails with molded plastic throwbar.

The Turnigy TrackStar range of 1/10th Brushed Motors is ideal for those that require a no-nonsense motor that will power your vehicle in any conditions. These motors are an ideal solution for backyard bashers or anyone wanting to cross rivers or travel in a wet environment.

The Turnigy TrackStar range of 1/10th Brushed Motors is ideal for those that require a no-nonsense motor that will power your vehicle in any conditions. These motors are an ideal solution for backyard bashers or anyone wanting to cross rivers or travel in a wet environment.

The Turnigy TrackStar range of 1/10th Brushed Motors is ideal for those that require a no-nonsense motor that will power your vehicle in any conditions. These motors are an ideal solution for backyard bashers or anyone wanting to cross rivers or travel in a wet environment.

The Turnigy TrackStar range of 1/10th Brushed Motors is ideal for those that require a no-nonsense motor that will power your vehicle in any conditions. These motors are an ideal solution for backyard bashers or anyone wanting to cross rivers or travel in a wet environment.

Aluminium Rear Bumper Type A - OH35A01 for the 1/35 Rock Crawler.

Keep the adventure going with high-quality spare parts for your TR-4. The replacement front C hubs are made of aluminum and are an excellent spare part to have handy.

The QUICRUN 880 Dual ESC is a durable, highly reliable waterproof electronic speed controller that has been designed for twin brushed motors in 1/10 and 1/8th scale vehicles. The HobbyWing patented copper heat conductive plates attached to the MOSFET board allows the internal heat to be quickly transferred to the aluminum heatsink for faster and greater heat dissipation.

Keep your car running smoothly with these high-quality spare parts designed specifically for the Blaze 1/10 Scale Cars. These 6-degree caster blocks work with the DCJ conversion as an option for different caster settings.

Each cell is hand-picked and matched for the ultimate in quality to deliver the power, durability and run time needed for the high performance models of today. Each pack is checked and tested at each stage of assembly to guarantee the highest possible quality. This careful matching and checking process allows the packs to achieve a mind boggling discharge rate of up to 140C. If you're the discerning racer or hardcore basher that needs to squeeze every last drop of performance out of your batteries, this is the pack for you!

HydroPro Inception Brushless RTR Deep Vee Racing Boat Replacement Hatch Sealing Rubber Gasket (2pcs).

HydroPro Inception Brushless RTR Deep Vee Racing Boat Replacement Drive Shaft Support Set.

HydroPro Inception Brushless RTR Deep Vee Racing Boat Replacement CNC Aluminum Rudder Assembly w/Plastic Mounting Bracket.

HydroPro Inception Brushless RTR Deep Vee Racing Boat Replacement Stainless Steel Turn Fins w/Mounting Set.

HydroPro Inception Brushless RTR Deep Vee Racing Boat Replacement Stainless Steel Trim Tabs w/Mounting Set.

A replacement aluminum alloy rudder support set for the Aquaholic V3 brushless racing boat.

A replacement coupler for connecting the motor to the 4mm flexi-shaft that will fit either the Aquaholic V2 or the V3 brushless racing boat.

A replacement short 5mm flexi-shaft for the 2024 version of the HydroPro Inception. Please see the attached pictures for the version that this suits.

The Rocket Surpass range of brushless motors is precision-made using the latest manufacturing processes. The heatsink can is CNC machined from a solid billet of 6061 T6 aluminum, high-purity copper is used for the windings for improved efficiency, and oversized bearings are used for durability. The stator has super thin (0.2mm) laminations, and the rotor is then precision balanced for reliability, and ultra-smooth running at maximum RPMs.

The Rocket Surpass 4076-2025KV motor has been specially built for 1/8th scale monster trucks and truggies. This 4-pole, 12-slot high-torque motor is water and dust-proof and features a universal mounting system to fit just about all 1/8th-scale vehicles.

This little kit takes around 4hrs to build and will satisfy the throttle jocky in all of us!

The flycat comes with 56mm EDF and you will need a 25A ESC & 4800kv inrunner.

This plane is extremely fast, (over 100mph!), however still stable at slow flight.

Spec.
WingSpan: 640mm
Length: 800mm
Weight: 290g
BESC : 25A (not included)
Motor: 4800kv 20-30 size Inrunner (not included)
Lipoly: 1300mAh 11.1v 20C (not included)

Required.
Motor & ESC
3 x 9g Servo
5 or 10min Epoxy (Araldite)
1 x Servo Y lead
1 x Servo Extention lead
12AWG Silicon wire (20cm For motor to ESC)
1300mah 11.1v 20C lipo battery
Your own receiver and transmitter

Our flight report.

Kit fits together well, light sanding of leading and trailing edges required to remove extra foam. We chose to not strengthen the wing with CF tubing, which didnt prove to be an issue, even at full speed high G turns.

We opted to mount the BESC being the battery area, in case the battery needed to be moved forward to adjust CofG, however this wasnt necessary.

EDF was mounted on the stick mount. Stick mount was shortened, with the extra piece used to raise the EDF off the stick to clear the EDF shroud. 2 bolts held the fan unit to the stick, one before and one after the fan blades.

First flight.

We kept CofG 9.5cm from the apex of the wings leading edge. The flycat was hand launched at 3/4 throttle, accelerating quickly. To our surprise, no trimming was required.

The flycat is an extremely fast kit to fly, and required a lot of elevator in turns. We suggest putting the elevator on maximum throws. It needs HUGE amounts of elevator during turns!

Overall an excellent plane which flys smoothly, even on windy days.

We suggest a good lipo pack, as this little hotty will chew through a 1500mAh in only 5 minutes. We used the ZIPPY-R 1800mAh 22C 3S1P pack for around 8 minute flights. As compared to the ZIPPY-Q pack which brought us short at about 7 minutes.

P-51D Shangri La - Replacement Horizontal Tail