Phantom FPV Flying Wing 1550mm - Replacement Motor Cover

Phantom FPV Flying Wing 1550mm - Replacement Vertical Stabilizer (1pair)

Phantom FPV Flying Wing 1550mm - Replacement Main Wing (1pair)

*Note* For V2 version only. V2 has removeable wing panels.

Keep your Telemetry Radios safe! These cases are made out of slightly translucent ABS plastic, so you still can see TX/RX LEDs. They have a very tight fit and finish and are clearly labeled. These cases will make your setup look like Pro gear, while keeping them safe!

Designed to fit FPV Radio Telemetry Kit - 915Mhz/433MHz(#42846/42847,not included), But fits other brand Telemetry Radios as well.

Includes:
3M Foam Double-tape X1
Ground module Case X1
Air module Case X1

Introducing our EPP 3D MX2. Featuring a fantastic design and layout, this all out EPP 3D'er will satisfy the most eager 3D pilots!

Its fuselage is torsionally very stiff yet light with loads of space beneath the long top hatch for your radio and power system. The wing is a one-piece affair featuring EPP construction, a very accurate symmetrical airfoil with 2 additional spars to minimize flex and twist. The control surfaces are something else - the elevator, rudder, and ailerons feature a 3 layer construction (Epp-Depron-EPP) making for stiff surfaces and NO flex at extreme throws! Snap rolls "Snap" and the control response is instantaneous.

The light - yet rigid - airframe adds up to one great flying 3D "foamy". Waterfalls, harriers, flat spins, rolling circles this model has the precision to perform these and any other moves you can think of!

Assembly of the airframe in a quick 10-15 minute process with the help of a little medium CA. The radio and power system layouts are very straightforward, the long top hatch making for easy access.

This is a great model for general park flying and hardcore 3D. You will be hard-pressed to break this model, it will take hard knocks and just keep bouncing back every time!


Features:
• Tough EPP material, light-weight, and crash-resistant
• Stiff EPP/Depron composite control surfaces
• Revolutionary design adds to the structural integrity and the rigidity of the airframe
• Light-weight provides optimal wing loading
• Outstanding aerobatic performance and 3D maneuverability.
• Simple design allows for easy equipment access and installation
• The stand out color scheme great for orientation


Specs:
Wingspan: 955mm
Length: 945mm
Wing Area: 15.2dm2
Weight: 550g (without battery)



Requires:
4 channel radio system
2217 950-1100KV Brushless outrunner 
30Amp ESC 
3S 11.1V 1100-1300MAH Li-Po 
10x4.7/11x4.7 propeller 
4 x 9g servos

Telemicro 520mm - Replacement Spinner

Suit HobbyKing Bixler 2

Spec.
Length: 41mm / 18mm(Horn Only)
Clip Size: 12 x 9.5mm

Hobbyking Bixler 2 EPO 1500mm - Replacement Pushrod Set

HobbyKing Bixler 2 EPO 1500mm -  Replacement Flap Hinges (6pcs/bag)

Works for both Bixler 2 and Bix3 models.

Hobbyking Bixler 2 EPO 1500mm - Replacement Aileron Hinges (10pcs/bag)

This little kit takes around 4hrs to build and will satisfy the throttle jocky in all of us!

The flycat comes with 56mm EDF and you will need a 25A ESC & 4800kv inrunner.

This plane is extremely fast, (over 100mph!), however still stable at slow flight.

Spec.
WingSpan: 640mm
Length: 800mm
Weight: 290g
BESC : 25A (not included)
Motor: 4800kv 20-30 size Inrunner (not included)
Lipoly: 1300mAh 11.1v 20C (not included)

Required.
Motor & ESC
3 x 9g Servo
5 or 10min Epoxy (Araldite)
1 x Servo Y lead
1 x Servo Extention lead
12AWG Silicon wire (20cm For motor to ESC)
1300mah 11.1v 20C lipo battery
Your own receiver and transmitter

Our flight report.

Kit fits together well, light sanding of leading and trailing edges required to remove extra foam. We chose to not strengthen the wing with CF tubing, which didnt prove to be an issue, even at full speed high G turns.

We opted to mount the BESC being the battery area, in case the battery needed to be moved forward to adjust CofG, however this wasnt necessary.

EDF was mounted on the stick mount. Stick mount was shortened, with the extra piece used to raise the EDF off the stick to clear the EDF shroud. 2 bolts held the fan unit to the stick, one before and one after the fan blades.

First flight.

We kept CofG 9.5cm from the apex of the wings leading edge. The flycat was hand launched at 3/4 throttle, accelerating quickly. To our surprise, no trimming was required.

The flycat is an extremely fast kit to fly, and required a lot of elevator in turns. We suggest putting the elevator on maximum throws. It needs HUGE amounts of elevator during turns!

Overall an excellent plane which flys smoothly, even on windy days.

We suggest a good lipo pack, as this little hotty will chew through a 1500mAh in only 5 minutes. We used the ZIPPY-R 1800mAh 22C 3S1P pack for around 8 minute flights. As compared to the ZIPPY-Q pack which brought us short at about 7 minutes.

P-51D Shangri La - Replacement Horizontal Tail

Prop Set for B-17 Memphis Belle 1875mm, 2 x Std Rotation, 2 x Reverse Rotation. 

10x7 3 blade props suitable for many models.

Durafly® ™ Micro Series - Replacement Motor Mount

Super Kinetic - Replacement Horizontal Wing (With Plastic Parts and Sticker)

Super Kinetic - Folding Propeller Set

Super Kinetic - Replacement Motor Mount

Super Kinetic - Replacement Canopy

Super Kinetic - Replacement Control Wire - Steel (With Ball Link)

Super Kinetic - Replacement Brushless Motor (2630-KV1000)

Super Kinetic - Replacement Decals (2pcs/set)

Durafly™ SkyMule 1500mm - Bottom Servo Hatch

HobbyKing® Bixler 3 Trainer 1550mm - Replacement Landing Gear

HobbyKing™ Bix3 Trainer 1550mm - Replacement Motor 2630 1400kv

HobbyKing® Bix3 Trainer 1550mm - Replacement Control Rod Set

HobbyKing® Bix3 Trainer 1550mm - Replacement Prop Adapter

HobbyKing™ Wingnetic 805mm - Replacement Folding Propeller

Specs:
Diameter: 7 in.
Pitch: 6

HobbyKing™ Bixler 3 Trainer 1550mm - Replacement Wing Spar

HobbyKing™ Bix3 Trainer 1550mm - Replacement Wing Bolts

2 Pieces Included

HobbyKing™ Super-G Autogyro - Auto Start System

Hobbyking™ Super-G Autogyro - Blade Grip Bolts

Includes 3 pieces

HobbyKing Hall Cherokee Glider 1700mm - Fuselage Set

EPO Fuselage with decals, plastic. control rods

Avios Yakovlev Yak-52 HobbyKing Scheme Replacement Canopy.

Avios Yakovlev Yak-52 Military Scheme Replacement Propeller Blades.