Introducing our EPP 3D MX2. Featuring a fantastic design and layout, this all out EPP 3D'er will satisfy the most eager 3D pilots!

Its fuselage is torsionally very stiff yet light with loads of space beneath the long top hatch for your radio and power system. The wing is a one-piece affair featuring EPP construction, a very accurate symmetrical airfoil with 2 additional spars to minimize flex and twist. The control surfaces are something else - the elevator, rudder, and ailerons feature a 3 layer construction (Epp-Depron-EPP) making for stiff surfaces and NO flex at extreme throws! Snap rolls "Snap" and the control response is instantaneous.

The light - yet rigid - airframe adds up to one great flying 3D "foamy". Waterfalls, harriers, flat spins, rolling circles this model has the precision to perform these and any other moves you can think of!

Assembly of the airframe in a quick 10-15 minute process with the help of a little medium CA. The radio and power system layouts are very straightforward, the long top hatch making for easy access.

This is a great model for general park flying and hardcore 3D. You will be hard-pressed to break this model, it will take hard knocks and just keep bouncing back every time!


Features:
• Tough EPP material, light-weight, and crash-resistant
• Stiff EPP/Depron composite control surfaces
• Revolutionary design adds to the structural integrity and the rigidity of the airframe
• Light-weight provides optimal wing loading
• Outstanding aerobatic performance and 3D maneuverability.
• Simple design allows for easy equipment access and installation
• The stand out color scheme great for orientation


Specs:
Wingspan: 955mm
Length: 945mm
Wing Area: 15.2dm2
Weight: 550g (without battery)



Requires:
4 channel radio system
2217 950-1100KV Brushless outrunner 
30Amp ESC 
3S 11.1V 1100-1300MAH Li-Po 
10x4.7/11x4.7 propeller 
4 x 9g servos

This little kit takes around 4hrs to build and will satisfy the throttle jocky in all of us!

The flycat comes with 56mm EDF and you will need a 25A ESC & 4800kv inrunner.

This plane is extremely fast, (over 100mph!), however still stable at slow flight.

Spec.
WingSpan: 640mm
Length: 800mm
Weight: 290g
BESC : 25A (not included)
Motor: 4800kv 20-30 size Inrunner (not included)
Lipoly: 1300mAh 11.1v 20C (not included)

Required.
Motor & ESC
3 x 9g Servo
5 or 10min Epoxy (Araldite)
1 x Servo Y lead
1 x Servo Extention lead
12AWG Silicon wire (20cm For motor to ESC)
1300mah 11.1v 20C lipo battery
Your own receiver and transmitter

Our flight report.

Kit fits together well, light sanding of leading and trailing edges required to remove extra foam. We chose to not strengthen the wing with CF tubing, which didnt prove to be an issue, even at full speed high G turns.

We opted to mount the BESC being the battery area, in case the battery needed to be moved forward to adjust CofG, however this wasnt necessary.

EDF was mounted on the stick mount. Stick mount was shortened, with the extra piece used to raise the EDF off the stick to clear the EDF shroud. 2 bolts held the fan unit to the stick, one before and one after the fan blades.

First flight.

We kept CofG 9.5cm from the apex of the wings leading edge. The flycat was hand launched at 3/4 throttle, accelerating quickly. To our surprise, no trimming was required.

The flycat is an extremely fast kit to fly, and required a lot of elevator in turns. We suggest putting the elevator on maximum throws. It needs HUGE amounts of elevator during turns!

Overall an excellent plane which flys smoothly, even on windy days.

We suggest a good lipo pack, as this little hotty will chew through a 1500mAh in only 5 minutes. We used the ZIPPY-R 1800mAh 22C 3S1P pack for around 8 minute flights. As compared to the ZIPPY-Q pack which brought us short at about 7 minutes.

This great-looking EDF sports jet is the one you have all been waiting for, and it has one of the lowest all-up weights in its class, it is a good 500g lighter than comparable models that are available on the market today. It is a sport scale design and is based on the iconic BAE Hawk trainer as used by military air forces all over the world. This easy-to-assemble model has been termed as an almost ready-to-fly-plus, it is completely built out of the box, the wings, all-flying horizontal stabilizers, and vertical stabilizer just bolt-on, and pre-installed are a set of all-metal electronic retracts with doors, sequencer control box, and lightweight wheels, 11 high-torque, metal-geared digital servos, and a set of pre-installed, day-bright LED lights. The Sports Hawk comes pre-painted in a Formula One-inspired paint scheme and includes a set of HobbyKing brand decals that you can apply if you wish. The pre-painted Sport Hawk color scheme lends itself nicely to having other sponsorship decals being applied, or you could even repaint it in a custom color scheme, the choice is yours. A nice touch is the removable base to the cockpit area which makes it very easy to add a pilot and more cockpit detail if you wish.

Are you ready to be the Red Baron of your local park?  Well with the fantastic Von Stik you can be a flying ace in minutes.   

A great slow stick design, the Von Stik has been made to be a super light, fly anywhere model, with a powerful geared motor running off  a 1S 3.7V 400mAh lipoly battery.  

Supplied with its own 2.4Ghz radio for interference free flying, easy to assemble and finished in a striking Red Baron finish, with the Von Stik you will be making diving attacks and strafing runs in no time at all.

It's easy to fly with its basic rudder and elevator control system and is very forgiving for the novice pilot.  In fact, the Von Stik makes for a perfect first model for any young person or even for the experienced pilot who is looking for a totally fun-fly aircraft that can be thrown up in a local park without any fuss.

Features:
• 2.4Gh radio system
• Light weight
• Easy to assemble
• Rudder/Elevator model
• Perfect for beginners 
• Beautiful bold "Red Baron" finish

Specs:
Wingspan: 52cm
Length: 38cm
RC System: 2.4Ghz
Propeller: 6050 (slowfly)
Weight: 75g
Battery Required: 1S 3.7V 350-400mAh Lipoly
Control Distance: 150m 
Mode: 2

Improving on the popular Bixler 2, this latest kit is the perfect trainer plane or inexpensive FPV platform. Attach your flight camera into the nose or canopy of the plane to enjoy First Person View while flying. The Bixler 3 kit requires a motor, ESCs, a radio system and battery. 

The H-King Crusader 30E is based on the classic stick design. This electric RC plane can be flown by both beginners and experts. It is constructed from lightweight ply and balsa that is painted with a high contrast color scheme. The Crusader will stand out on the ground and in the air at your local hobby club.

The Bixler 1.1 is a proven platform for beginners right through to intermediate pilots. Well known for stability, the Bixler is also an excellent choice for an inexpensive FPV platform and perfect for those lazy Sunday afternoons.

This version of the Bixler 1.1 is not supplied with a motor, ESC, servos, or RC equipment, it allows you to choose yourself the components you wish to use. Whatever you are looking for, the Bixler 1.1 has it covered.

The Ranger 2000 is easy to assemble and features a large wingspan which provides stability, and also allows the model to fly at slow speeds. The EPO wings are fitted with two spars for strength and each aileron is reinforced with carbon to eliminate any chance of distortion or twisting. The wings are attached to the fuselage using fast connect clips, after flying, simply squeeze the clips to release the wings.

The Phoenix V2 2000 is a quick and easy to assemble electric powered glider with flaps and large ailerons for a precise, aerobatic performance. The EPO wings are fitted with a carbon spar for strength and 2 metal spars join the wings to the fuselage. Also, each aileron is reinforced with carbon to eliminate any chance of distortion or twisting. The wings are attached to the fuselage using fast connect clips, after flying, simply squeeze the clips to release the wings.

The Phoenix 2400 is an extended wing version of the popular Phoenix 1600mm and 2000mm range of electric powered gliders. Assembly is quick and easy with no glue required, the vertical fin and horizontal stabilizer are simply screwed to the rear of the fuselage. The EPO wings are fitted with a carbon spar for strength and 2 metal spars join the wings to the fuselage. Also, each aileron is reinforced with carbon to eliminate any chance of distortion or twisting. The wings are attached to the fuselage using fast connect clips, after flying, simply squeeze the clips to release the wings.

The Wargo Signature Edge 540T 3D is yet another incredible airplane in the series inspired by the renowned 3D pilot Michael Wargo. The Edge 540T was specifically designed for very precise 3D flying and aerobatic training. Michael Wargo, our team pilot, and 3D expert, wanted a foam aircraft that was stiffer, and lighter than other foamies. This was achieved by the combination of a stiff, lightweight balsa frame covered with lightweight, crash-resistant EPP foam.

The Dancing Wings Hobby Fokker Eindecker III is a scale model of the famous World War 1 monoplane fighter. The kit comes almost ready to fly and is constructed in balsa for a strong, lightweight, authentic structure. A lot of scale detail is supplied including, a dummy engine, scale wheels, and a dummy machine gun, plus a full accessory kit is also supplied which includes all the necessary hardware including scale rigging to complete the kit.

The Dancing Wings Hobby S.E.5A is a detailed scale model of the famous World War 1 biplane fighter. The kit comes almost ready to fly and is constructed in balsa for a strong, lightweight, authentic structure. A lot of scale detail is supplied including, scale exhausts, scale wheels, and a dummy machine gun, plus a full accessory kit is also supplied which includes all the necessary hardware including scale rigging to complete the kit.

We have all had to start learning to fly an RC model at some point, and a stable, high-wing trainer that is very forgiving is what is required. The Dancing Wings Hobby Vogee-16 Trainer is the perfect choice for the rookie pilot. It has a large, flat-bottomed wing with dihedral which enables it to fly very slowly, and it has the stability to sort itself out if you get in a muddle. The Vogee's flying characteristics are very benign, beginners tend to over-control, and the Vogee is very gentle in its handling, especially if you install one of the readily available 3-axis gyros that are available on the market these days. It also has a tricycle landing gear with a steerable nosewheel which really helps with the take-offs and landings. This version of the Vogee is supplied with a powerful 2817-900KV brushless motor, a 60A brushless ESC, an 11" prop, 2 x 37g servos, and 2 x 17g 

The Dancing Wings Hobby Stick-14T 3D aerobatic trainer is the perfect choice for intermediate and experienced RC pilots alike. It is based on the classic stick design and is quite capable of all the usual aerobatic maneuvers, plus with the right power train, it doubles up as the perfect 3D trainer. It has a very wide speed range, it is just as happy flying slowly as it is screaming about the sky. For added fun and enjoyment, the strip ailerons are split halfway making for outboard ailerons and inboard flaps. This allows for really slow or steep approach landings, and if the flaps are mixed in with your other controls it allows you to customize the handling to suit your own flying style. 

The Dancing Wings Hobby Aion laser cut balsa kit is an easy-build electric sports glider that includes ailerons and flaps. The Aion is aimed at the modeler who wants to experience real model-making but wants something that is reasonably straightforward to build. This is achieved with the use of accurate laser-cut parts and the simple box-type fuselage which produce a strong, accurate, lightweight structure. The Aion is relatively easy to build, however, we do recommend that some experience in building a wood model airplane has been gained previously. Most of the components are constructed over the detailed, high-quality printed 1:1 building plan. This outstanding kit is supplied with a powerful 2216-920KV brushless motor, a 30A brushless ESC, an 11" folding prop with metal spinner, 6 x 9g servos, and an iron-on covering film pack

The Dancing Wings Hobby Savage Bobber is a small, lightweight foam model that is quick and simple to build. The full-size Savage Bobber was devised by the Zlin Aviation Company. The Bobber as in the motorcycle world means that it is a stripped-down, customized version of an original. The Savage Bobber is a stripped-down, customized version of its older brother the Savage Classic. It is lighter, more maneuverable, and has a slightly narrower fuselage, and the absence of covering to the rear of the fuselage greatly improves the crosswind handling.

The model is reasonably straightforward to assemble, it is manufactured in pre-painted high-quality EPP foam sheet for the majority of the construction, tough plastic for the open framework rear fuselage, and lightweight balsa for the internal structure. Carbon strips are also included to reinforce and improve the stiffness of the structure. It builds up quickly into a good-looking, fun-to-fly lightweight (only 98g) sports plane that is perfect for indoor or park flying. This ARF kit is supplied with a powerful 1108-4000KV brushless motor, 5A brushless ESC, 5" propeller, and 4 x 2g servos.

The Dancing Wings Hobby Shining is a large lightweight profile-style foam kit that is quick and simple to build. It has been designed to be the perfect introduction to 3D flying and will perform extreme 3D maneuvers such as waterfalls, harriers, knife-edge loops, rolling circles, and much more.

The model is very straightforward to assemble, it is manufactured in pre-painted high-quality EPP foam sheet for the majority of the construction so the parts count is quite low, and carbon strips are supplied for strengthening. It builds up quickly into a good-looking, fun-to-fly lightweight extreme sport 3D plane that is perfect for park flying and on playing fields. This ARF model is supplied with a powerful 2216-950KV brushless motor, 30A brushless ESC, 10" propeller, and 4 x 9g servos.

Looking for the perfect trainer? Or an in-expensive FPV platform? Maybe you are a club pilot looking for something you can just pull out of the car and fly on one of those lazy Sunday afternoons? The Hobbyking® ™ Bixler® ™ 2 ticks all of these boxes and more! The Bixler® ™ 2 has had some improvements to make it even better such as a bigger air inlet for better motor cooling.