Connectors

MPX Connector to T-Connector Battery Adapter Lead(2pcs)

This adapter will convert a MPX Connector equipped battery to a T-Connector for use with an T-Connector equipped ESC or an T-Connector Charge lead.

2mm Gold connectors with cut away for easy soldering

Package contains 10 PAIRS of connectors. (20pc)

Spec.
Length: 12.5mm(Each)
Diameter: 2mm
Weight: 0.4g(Pair)

XT90 Battery Harness 10AWG for 2 Packs in Series

IMPORTANT: "These are not cheap copied XT90 plugs. These original Nylon XT90 plugs, manufactured by AMASS, can handle over 90A current for extended periods without exceeding 80DegC thanks to their better contact surface area. The plug is also less likely to deform or melt in comparison to copied non-Nylon XT90 plugs."

XT90 Battery Harness 10AWG for 2 Packs in Parallel

IMPORTANT: "These are not cheap copied XT90 plugs. These original Nylon XT90 plugs, manufactured by AMASS, can handle over 90A current for extended periods without exceeding 80DegC thanks to their better contact surface area. The plug is also less likely to deform or melt in comparison to copied non-Nylon XT90 plugs."

XT150s are big 6mm sprung gold connectors that have a large contact area, making them great for high power applications up to 250A!

4mm Gold Connectors - Low Profile (10pc)

Ideal for use with Hardcase packs for RC cars these plugs will allow you to fit your battery in the tightes of battery compartments.

Low Profile Bullect Connectors are preferred by racers world wide.

Pro Tip: If you find the bullets hard to plug in to your battery take a set of needle nose pliers and gently squeeze two of the four prongs, turn the plug and repeat on the other two prongs. If the plug is too loose take a small Phillips head screw driver and gently force the prongs open a little until you have a snug fit.

2.1mm - 5.5mm DC Chassis Socket Jack (2pc)

Specs:
Outside Dia: 5.5mm
Inside Dia: 2.1mm
Connector: Socket.
Connector Type: Female/DC
Connection: Solder type

2.5mm - 5.5mm DC Chassis Socket Jack (2pc)

Specs:
Outside Dia: 5.5mm
Inside Dia: 2.5mm
Connector: Socket.
Connector Type: Female/DC
Connection: Solder type

Molex 2 Pin Cable Female Connector with 220mm x 26AWG Wire.

Specs:
Connector: Molex 2 pin
Colour: Black, Red
Length: 220mm

Molex 3 Pin Cable Male Connector with 220mm x 26AWG Wire

Specs:
Connector: Molex 3 pin
Colour: Black, Yellow, Red
Length: 220mm

7mm AS150 Anti Spark Self Insulating Bullet Connector (2 Pairs)

This connector features an insulated tip to stop big sparks from higher voltage applications. This coupled with the plastic self insulating shroud offers a safe and affective connector package with no shrink tube needed.

Male Gold Plated Spring Connector 4mm (10pcs/bag)

5mm Male Gold Plated Spring Connector - Low Profile (10pcs)

Pro Tip: If you find the bullets hard to plug in to your battery, take a set of needle nose pliers and gently squeeze two of the six prongs, turn the plug and repeat on the other four prongs. If the plug is too loose take a small Phillips head screw driver and gently force the prongs open a little until you have a snug fit.

With the growing popularity of high voltage setups on R/C model helicopters, EDFs and airplanes,
sparking battery connections are increasingly becoming the biggest enemy to your electronics.

All the anti-spark systems in the market today require some sort of modification or DIY work before use.

Now, we have just the solution. XT-90S is based on the popular XT90 but now integrates an anti-spark system. With the XT90-S, no need to invest to a secondary anti-spark system (which provides an additional failure point to your system).

100% compatible with existing XT90.
Comes with a soldering cover to protect the solder point.

Spec.
Weight: 15.3g(Each Pair)
Size: 49x21x10mm(Each Pair)

IMPORTANT: "These are not cheap copied XT90 plugs. These original Nylon XT90 plugs, manufactured by AMASS, can handle over 90A current for extended periods without exceeding 80DegC thanks to their better contact surface area. The plug is also less likely to deform or melt in comparison to copied non-Nylon XT90 plugs."

2.1mm PCB Mounted DC Power Socket (5pcs)

Specs:
Internal Pin Diameter: 2.1mm
External Socket Diameter: 5.5mm
Length: 14mm
Height: 11mm
Width: 9mm
Max Rating: 1amp @ 12v
Quantity: 5pcs

2.5mm PCB Mounted DC Power Socket (5pcs)

Specs:
Internal Pin Diameter: 2.5mm
External Socket Diameter: 5.5mm
Length: 14mm
Height: 11mm
Width: 9mm
Max Rating: 1amp @ 12v
Quantity: 5pcs

The MT60 3 Pole Motor Connector set is the perfect solution for securing your brushless motor / ESC connections. The connector set features male and female connectors which are both fitted with 3.5mm bullets and supplied with a cable tidy attachment to keep things nice and neat!

The connectors are manufactured from toughened plastic and provide a very secure fit making them perfect for EDF and multi rotor applications.

Specs:
Dimensions: 46 x 12 x 12mm (assembled)
Weight: 9.70g (per set)
Suitable for: 12AWG wire (Max)
Color: Yellow

The MT60 3 Pole Motor Connector set is the perfect solution for securing your brushless motor / ESC connections. The connector set features male and female connectors which are both fitted with 3.5mm bullets and supplied with a cable tidy attachment to keep things nice and neat!

The connectors are manufactured from toughened plastic and provide a very secure fit making them perfect for EDF and multi rotor applications.

Specs:
Dimensions: 46 x 12 x 12mm (assembled)
Weight: 9.70g (per set)
Suitable for: 12AWG wire (Max)
Color: Black

2.1mm DC Power Plug to 2.1mm DC Power Socket Extension Lead (2pcs)

Specs:
Plug Internal Diameter: 2.1mm
Plug External Diameter: 5.5mm
Plug Length: 12mm
Socket Internal Pin: 2.1mm
Socket Internal Diameter: 5.5mm
Overall length: 1m
Max rating: 1amp @ 12V
Quantity: 2pcs

2.5mm DC Power Plug to 2.5mm DC Power Socket Extension Lead (2pcs)

Specs:
Plug Internal Diameter: 2.5mm
Plug External Diameter: 5.5mm
Plug Length: 12mm
Socket Internal Pin: 2.5mm
Socket Internal Diameter: 5.5mm
Overall length: 1m
Max rating: 1amp @ 12V
Quantity: 2pcs

1.3mm DC Power Plug to 2.1mm DC Power Socket Adapter (2pcs)

Specs:
Plug Internal Diameter: 1.3mm
Plug External Diameter: 3.5mm
Plug Length: 10mm
Socket Internal Pin: 2.1mm
Socket Internal Diameter: 5.5mm
Overall length: 160mm
Max rating: 1amp @ 12V
Quantity: 2pcs

1.3mm DC Power Plug with 15cm Lead (2pcs)

Specs:
Internal Diameter: 1.3mm
External Diameter: 3.5mm
Plug Length: 10mm
Overall length: 35mm
Wire: Red/Black 150mm
Max rating: 1amp @ 12V
Quantity: 2pcs

The MT30 3 Pole connector set is the perfect solution for connecting your brushless motor to your ESC. This set features both male and female connectors which are fitted with 2mm gold plated bullets. These are perfect for 16AWG wire, and the supplied cable tidy attachment keeps things nice and neat!

The connectors are manufactured from toughened plastic and provide a very secure fit making them perfect for EDF and multi-rotor applications.

The popular T style plug and socket has been improved with the addition of clip-on insulating caps. These caps replace the need for heatshrink tubing and will accommodate up to 10awg wire.

The new XT60+ is here!  With "snap on" insulating end caps to provide the best polarity insulation for your soldered connections, these are sure to become the most popular battery connector for hobbyists.

The basis of the original robust XT60 design has been retained and the connector is compatible with the original XT60, but now thanks to the snap on end cap there is no need to use heat shrink and the ridged edges on the end cap provide extra grip when pulling the male and female connectors apart.

Initial assembly requires a little force to clamp the end cap in place but please note that the end cap is hard to disassemble once it has been installed.  Should you wish to remove the end cap  you will have to "break it" with both hands to get it to release.  

These are genuine AMAAS connectors and are quality products, our customers should beware of imitations in the market that do not meet these standards.  

Specs:
Material: Gold-plated copper
External Material: Nylon/PA
Max. RC/MC: 60A/100A
Weight: 7.72g
Pulling Force/600: 3kg
Temperature Resistance: -20°C~120°C
Recommended Cable Spec.: 12AWG
Recommended Soldering Spec.: 480°C/4S

Includes:
5 sets of male and female plugs

IMPORTANT: "These are not cheap copied XT60 plugs. These original Nylon XT60 plugs, manufactured by AMASS, can handle over 60A current for extended periods without exceeding 80DegC thanks to their better contact surface area. The plug is also less likely to deform or melt in comparison to copied non-Nylon XT60 plugs."

The new XT60+ is here!  With "snap on" insulating end caps to provide the best polarity insulation for your soldered connections, these are sure to become the most popular battery connector for hobbyists.

The basis of the original robust XT60 design has been retained and the connector is compatible with the original XT60, but now thanks to the snap on end cap there is no need to use heatshrink and the ridged edges on the end cap provide extra grip when pulling the male and female connectors apart.

Initial assembly requires a little force to clamp the end cap in place but please note that the end cap is hard to disassemble once it has been installed.  Should you wish to remove the end cap  you will have to "break it" with both hands to get it to release.  

These are genuine AMAAS connectors and are quality products, our customers should beware of imitations in the market that do not meet these standards. 

Specs:
Material: Gold-plated copper
External Material: Nylon/PA
Max. RC/MC: 60A/100A
Weight: 7.72g
Pulling Force/600: 3kg
Temperature Resistance: -20°C~120°C
Recommended Cable Spec.: 12AWG
Recommended Soldering Spec.: 480°C/4S

Includes:
5 x male plugs

IMPORTANT: "These are not cheap copied XT60 plugs. These original Nylon XT60 plugs, manufactured by AMASS, can handle over 60A current for extended periods without exceeding 80DegC thanks to their better contact surface area. The plug is also less likely to deform or melt in comparison to copied non-Nylon XT60 plugs."

The new XT60+ is here!  With "snap on" insulating end caps to provide the best polarity insulation for your soldered connections, these are sure to become the most popular battery connector for hobbyists.

The basis of the original robust XT60 design has been retained and the connector is compatible with the original XT60, but now thanks to the snap on end cap there is no need to use heatshrink and the ridged edges on the end cap provide extra grip when pulling the male and female connectors apart.

Initial assembly requires a little force to clamp the end cap in place but please note that the end cap is hard to disassemble once it has been installed.  Should you wish to remove the end cap  you will have to "break it" with both hands to get it to release.  

These are genuine AMAAS connectors and are quality products, our customers should beware of imitations in the market that do not meet these standards. 

Specs:
Material: Gold-plated copper
External Material: Nylon/PA
Max. RC/MC: 60A/100A
Weight: 7.72g
Pulling Force/600: 3kg
Temperature Resistance: -20°C~120°C
Recommended Cable Spec.: 12AWG
Recommended Soldering Spec.: 480°C/4S

Includes:
5 x female plugs

IMPORTANT: "These are not cheap copied XT60 plugs. These original Nylon XT60 plugs, manufactured by AMASS, can handle over 60A current for extended periods without exceeding 80DegC thanks to their better contact surface area. The plug is also less likely to deform or melt in comparison to copied non-Nylon XT60 plugs." 

Ideal for making a neat job of a charging station etc.

Features:
• Male/Female XT60 connector
• Panel mounting bracket
• Neat XT60 protective cover
• Mounting screw set.

IMPORTANT: "These are not cheap copied XT60 plugs. These original Nylon XT60 plugs, manufactured by AMASS, can handle over 60A current for extended periods without exceeding 80DegC thanks to their better contact surface area. The plug is also less likely to deform or melt in comparison to copied non-Nylon XT60 plugs."

Losi Mini Plug Pigtail - Battery (2pcs/bag)

7cm wire with pre-tinned ends.

Excellent W.S. Deans T-connector replacements.

Made from high-temp Nylon and gold plated spring connectors, both included in the injection mould at the time when forming the connector. The XT60 ensures a solid high-amp connection, perfect for applications up to and beyond 65A constant.

Hobbyking will begin to include the XT60 on all batteries up to 3,000mAh in capacity in the near future!

XT60, Designed by hexTronik to be more reliable and a better quality connection than Deans T-Connectors.

There is no patent on the XT60 connector, we hope this product is sold everywhere in the world and dominates the market, reducing customers dependency on the over-priced Deans T-connector.

Say 'No' to the Deans Connector profiteers, and use XT-60's!

IMPORTANT: "These are not cheap copied XT60 plugs. These original Nylon XT60 plugs, manufactured by AMASS, can handle over 60A current for extended periods without exceeding 80DegC thanks to their better contact surface area. The plug is also less likely to deform or melt in comparison to copied non-Nylon XT60 plugs."

Genuine Nylon high-temp XT60 connectors.
XT = heXTronik
60 = 60A constant
We're the guys that designed this plug!

This is a great way to avoid power shorts.
Rated to around 120A

Gold connectors on their own are notorious for creating a short circuit and looking messy. Use these to keep your connections safe and looking neat!
 
Easier to solder and a stronger connection than Deans T-plugs

EC2 Male - ESC Connector (5pcs/bag)

EC2 Female & Male (5pcs/bag)

XT60 Harness for 2 Packs in Parallel (1pc)

Spec:
Weight: 11.2g

IMPORTANT: "These are not cheap copied XT60 plugs. These original Nylon XT60 plugs, manufactured by AMASS, can handle over 60A current for extended periods without exceeding 80DegC thanks to their better contact surface area. The plug is also less likely to deform or melt in comparison to copied non-Nylon XT60 plugs."

JST-XH to JST LED Power Distribution Lead - A neat way to power LED's from 3s Lipoly's using the balance plug.



** WARNING: Check Polarity of your setup before connecting this harness.