Accessories

1.3mm DC Power Plug to 2.1mm DC Power Socket Adapter (2pcs)

Specs:
Plug Internal Diameter: 1.3mm
Plug External Diameter: 3.5mm
Plug Length: 10mm
Socket Internal Pin: 2.1mm
Socket Internal Diameter: 5.5mm
Overall length: 160mm
Max rating: 1amp @ 12V
Quantity: 2pcs

1.3mm DC Power Plug with 15cm Lead (2pcs)

Specs:
Internal Diameter: 1.3mm
External Diameter: 3.5mm
Plug Length: 10mm
Overall length: 35mm
Wire: Red/Black 150mm
Max rating: 1amp @ 12V
Quantity: 2pcs

The MT30 3 Pole connector set is the perfect solution for connecting your brushless motor to your ESC. This set features both male and female connectors which are fitted with 2mm gold plated bullets. These are perfect for 16AWG wire, and the supplied cable tidy attachment keeps things nice and neat!

The connectors are manufactured from toughened plastic and provide a very secure fit making them perfect for EDF and multi-rotor applications.

The popular T style plug and socket has been improved with the addition of clip-on insulating caps. These caps replace the need for heatshrink tubing and will accommodate up to 10awg wire.

The new XT60+ is here!  With "snap on" insulating end caps to provide the best polarity insulation for your soldered connections, these are sure to become the most popular battery connector for hobbyists.

The basis of the original robust XT60 design has been retained and the connector is compatible with the original XT60, but now thanks to the snap on end cap there is no need to use heat shrink and the ridged edges on the end cap provide extra grip when pulling the male and female connectors apart.

Initial assembly requires a little force to clamp the end cap in place but please note that the end cap is hard to disassemble once it has been installed.  Should you wish to remove the end cap  you will have to "break it" with both hands to get it to release.  

These are genuine AMAAS connectors and are quality products, our customers should beware of imitations in the market that do not meet these standards.  

Specs:
Material: Gold-plated copper
External Material: Nylon/PA
Max. RC/MC: 60A/100A
Weight: 7.72g
Pulling Force/600: 3kg
Temperature Resistance: -20°C~120°C
Recommended Cable Spec.: 12AWG
Recommended Soldering Spec.: 480°C/4S

Includes:
5 sets of male and female plugs

IMPORTANT: "These are not cheap copied XT60 plugs. These original Nylon XT60 plugs, manufactured by AMASS, can handle over 60A current for extended periods without exceeding 80DegC thanks to their better contact surface area. The plug is also less likely to deform or melt in comparison to copied non-Nylon XT60 plugs."

The new XT60+ is here!  With "snap on" insulating end caps to provide the best polarity insulation for your soldered connections, these are sure to become the most popular battery connector for hobbyists.

The basis of the original robust XT60 design has been retained and the connector is compatible with the original XT60, but now thanks to the snap on end cap there is no need to use heatshrink and the ridged edges on the end cap provide extra grip when pulling the male and female connectors apart.

Initial assembly requires a little force to clamp the end cap in place but please note that the end cap is hard to disassemble once it has been installed.  Should you wish to remove the end cap  you will have to "break it" with both hands to get it to release.  

These are genuine AMAAS connectors and are quality products, our customers should beware of imitations in the market that do not meet these standards. 

Specs:
Material: Gold-plated copper
External Material: Nylon/PA
Max. RC/MC: 60A/100A
Weight: 7.72g
Pulling Force/600: 3kg
Temperature Resistance: -20°C~120°C
Recommended Cable Spec.: 12AWG
Recommended Soldering Spec.: 480°C/4S

Includes:
5 x male plugs

IMPORTANT: "These are not cheap copied XT60 plugs. These original Nylon XT60 plugs, manufactured by AMASS, can handle over 60A current for extended periods without exceeding 80DegC thanks to their better contact surface area. The plug is also less likely to deform or melt in comparison to copied non-Nylon XT60 plugs."

The new XT60+ is here!  With "snap on" insulating end caps to provide the best polarity insulation for your soldered connections, these are sure to become the most popular battery connector for hobbyists.

The basis of the original robust XT60 design has been retained and the connector is compatible with the original XT60, but now thanks to the snap on end cap there is no need to use heatshrink and the ridged edges on the end cap provide extra grip when pulling the male and female connectors apart.

Initial assembly requires a little force to clamp the end cap in place but please note that the end cap is hard to disassemble once it has been installed.  Should you wish to remove the end cap  you will have to "break it" with both hands to get it to release.  

These are genuine AMAAS connectors and are quality products, our customers should beware of imitations in the market that do not meet these standards. 

Specs:
Material: Gold-plated copper
External Material: Nylon/PA
Max. RC/MC: 60A/100A
Weight: 7.72g
Pulling Force/600: 3kg
Temperature Resistance: -20°C~120°C
Recommended Cable Spec.: 12AWG
Recommended Soldering Spec.: 480°C/4S

Includes:
5 x female plugs

IMPORTANT: "These are not cheap copied XT60 plugs. These original Nylon XT60 plugs, manufactured by AMASS, can handle over 60A current for extended periods without exceeding 80DegC thanks to their better contact surface area. The plug is also less likely to deform or melt in comparison to copied non-Nylon XT60 plugs." 

Landing Gear Wheel Stopper (10pcs)

To suit 3mm Shaft

Landing Gear Wheel Stopper (10pcs)
To suit 5mm Shaft

Linkage Stopper D2.1mm (10sets)

Scale wheels, split hub type, rubber "air" tyre, removable hub covers.

Size: 2in  D51×Φ4×H13mm

Weight: 19g Per Wheel

Warbird/Scale wheels, split hub type, rubber "air" tyre, removable hub covers.

Size:2.75in  D70×Φ4×H23mm

Weight: 55g Per Wheel

Warbird/Scale wheels, split hub type, rubber "air" tyre, removable hub covers.

Size: 4in  D102×Φ6×H26mm

Weight: 118g Per Wheel

Heavy duty control rods with ball link ends (2pcs/bag)

 Size：M4+M4×L83mm

Carbon Fiber Tail wheel set 26cc~30cc

Size:
Length:118mm
Width:14.0mm
Thickness:2.6mm 

Carbon Fiber Tail wheel set 85cc-100cc        

Size:
Length:190mm
Width:18.2mm
Thickness:3.5mm

Model JET Pilot 1/6 (Green) (H80 x W68 x D37mm)

Made with what seems to be a flexible rubber or plastic.
Well detailed and nicely painted.
A good addition to any plane.

Specs
Heigth: 80mm
Width: 68mm
Depth: 37mm
Weight: 29g

Ultra Light Parkfly Pilot (Green) (H30 x W37 x D18mm) - Perfect for even the lightest parkfly model!

Specs
Height: 30mm
Width: 37mm
Depth: 18mm
Weight: 2g

Ultra Light Parkfly Pilot (Red) (H30 x W37 x D19mm) - Perfect for even the lightest parkfly model!

Specs
Height: 30mm
Width: 37mm
Depth: 19mm
Weight: 2g

Parkfly Classic Era Pilot (Red) (H37 x W40 x D22mm)

Specs
Height: 37mm
Width: 40mm
Depth: 22mm
Weight: 6g

Parkfly Luftwaffe Pilot (H38 x W39 x D23mm)

Specs
Height: 38mm
Width: 39mm
Depth: 23mm
Weight: 7g

This is a very neat device for securing your models hatches. This latch is spring loaded so once latched your canopy stays put!

Specs:
Dimensions: 26 x 16 x 8mm + 15mm pin length 
Material: Aluminum

This is a very neat device for securing your models hatches. This latch is spring loaded so once latched your canopy stays put!

Specs:
Dimensions: 23.5 x 13 x 8mm + 8mm pin length
Material: Plastic / Steel

This is a very neat device for securing your models hatches. This latch is spring loaded so once latched your canopy stays put!

Specs:
Dimensions:  26x16x10mm + 10mm pin Length
Material: Plastic / brass

These are used to help route cables and hoses within your models. These anchors are self adhesive and allow you to pass a cable tie through the anchor, then around the cable or hose you wish to hold in position.

Handy for use in both your models and the workshop!

Dimensions: 25 x 25mm 

Metal Push Rods M2xL550 with one-end threaded

Nylon Ball Joint M3 x 24mm x 3mm

Nylon Ball Joint M2.5 x 27mm x 3mm (2pcs)

Suitable to fit small electric motors which have threaded prop shafts, these rubber safety spinners push over the shaft, prop retaining nut and the prop to create a safe forward projection of your model, particularly important when flying at indoor events.

Specs:
Diameter: 23mm
Length: 32mm

Landing Gear Straps (Nylon) 10pc

Specs:
Length: 22mm
Width: 10mm
Hole Centers: 12mm
Material: Nylon

This POM clevis uses a 2mm nut and bolt instead of a plastic pin, used with loctite this makes a very strong and secure linkage.

Specs:
Overall Length: 29mm
Pushrod Size: M2
Material: Clear nylon

Very well formed, light weight and firm, foam wheels.

Specs:
Diameter: 65mm
Width: 10mm
Material: Foam (Tyres) Plastic (Hub)
Weight: 7.5g (Per wheel)

Lock on nylon control horn for ailerons, elevators, rudders and similiar applications. The backplate pushes over the serrations on the horn and locks it into place, no need for glue.

Specs:
Length of Horn from Base: 18mm
Max Thickness of Control Surface: 6mm
Length of Base: 12mm
Width of Base: 8mm
Material: Nylon
Fixing: Lock on

Ideal for making a neat job of a charging station etc.

Features:
• Male/Female XT60 connector
• Panel mounting bracket
• Neat XT60 protective cover
• Mounting screw set.

IMPORTANT: "These are not cheap copied XT60 plugs. These original Nylon XT60 plugs, manufactured by AMASS, can handle over 60A current for extended periods without exceeding 80DegC thanks to their better contact surface area. The plug is also less likely to deform or melt in comparison to copied non-Nylon XT60 plugs."