Accessories

Large horn with roller eyelet and clevis (5sets)

Alloy Adjustable Horn W Base/Bearing 2.8x24mm (5sets)

Extra Strong Control Horns w/ Bearing 34mm (5pcs)
diam2.8mm x 34mm

Nylon & Pinned Hinge 16x28.5

Hatch type hinge (5pcs)
 

Nylon Clevis 3x22mm (10pcs)

Nylon Clevis
M3 Size
Length 27mm

Micro Clevis 1.2x22mm (10pcs)

XT150s are big 6mm sprung gold connectors that have a large contact area, making them great for high power applications up to 250A!

2.1mm - 5.5mm DC Chassis Socket Jack (2pc)

Specs:
Outside Dia: 5.5mm
Inside Dia: 2.1mm
Connector: Socket.
Connector Type: Female/DC
Connection: Solder type

2.5mm - 5.5mm DC Chassis Socket Jack (2pc)

Specs:
Outside Dia: 5.5mm
Inside Dia: 2.5mm
Connector: Socket.
Connector Type: Female/DC
Connection: Solder type

Molex 2 Pin Cable Female Connector with 220mm x 26AWG Wire.

Specs:
Connector: Molex 2 pin
Colour: Black, Red
Length: 220mm

Molex 3 Pin Cable Male Connector with 220mm x 26AWG Wire

Specs:
Connector: Molex 3 pin
Colour: Black, Yellow, Red
Length: 220mm

7mm AS150 Anti Spark Self Insulating Bullet Connector (2 Pairs)

This connector features an insulated tip to stop big sparks from higher voltage applications. This coupled with the plastic self insulating shroud offers a safe and affective connector package with no shrink tube needed.

Male Gold Plated Spring Connector 4mm (10pcs/bag)

5mm Male Gold Plated Spring Connector - Low Profile (10pcs)

Pro Tip: If you find the bullets hard to plug in to your battery, take a set of needle nose pliers and gently squeeze two of the six prongs, turn the plug and repeat on the other four prongs. If the plug is too loose take a small Phillips head screw driver and gently force the prongs open a little until you have a snug fit.

With the growing popularity of high voltage setups on R/C model helicopters, EDFs and airplanes,
sparking battery connections are increasingly becoming the biggest enemy to your electronics.

All the anti-spark systems in the market today require some sort of modification or DIY work before use.

Now, we have just the solution. XT-90S is based on the popular XT90 but now integrates an anti-spark system. With the XT90-S, no need to invest to a secondary anti-spark system (which provides an additional failure point to your system).

100% compatible with existing XT90.
Comes with a soldering cover to protect the solder point.

Spec.
Weight: 15.3g(Each Pair)
Size: 49x21x10mm(Each Pair)

IMPORTANT: "These are not cheap copied XT90 plugs. These original Nylon XT90 plugs, manufactured by AMASS, can handle over 90A current for extended periods without exceeding 80DegC thanks to their better contact surface area. The plug is also less likely to deform or melt in comparison to copied non-Nylon XT90 plugs."

The MT60 3 Pole Motor Connector set is the perfect solution for securing your brushless motor / ESC connections. The connector set features male and female connectors which are both fitted with 3.5mm bullets and supplied with a cable tidy attachment to keep things nice and neat!

The connectors are manufactured from toughened plastic and provide a very secure fit making them perfect for EDF and multi rotor applications.

Specs:
Dimensions: 46 x 12 x 12mm (assembled)
Weight: 9.70g (per set)
Suitable for: 12AWG wire (Max)
Color: Yellow

The MT60 3 Pole Motor Connector set is the perfect solution for securing your brushless motor / ESC connections. The connector set features male and female connectors which are both fitted with 3.5mm bullets and supplied with a cable tidy attachment to keep things nice and neat!

The connectors are manufactured from toughened plastic and provide a very secure fit making them perfect for EDF and multi rotor applications.

Specs:
Dimensions: 46 x 12 x 12mm (assembled)
Weight: 9.70g (per set)
Suitable for: 12AWG wire (Max)
Color: Black

The MT30 3 Pole connector set is the perfect solution for connecting your brushless motor to your ESC. This set features both male and female connectors which are fitted with 2mm gold plated bullets. These are perfect for 16AWG wire, and the supplied cable tidy attachment keeps things nice and neat!

The connectors are manufactured from toughened plastic and provide a very secure fit making them perfect for EDF and multi-rotor applications.

The new XT60+ is here!  With "snap on" insulating end caps to provide the best polarity insulation for your soldered connections, these are sure to become the most popular battery connector for hobbyists.

The basis of the original robust XT60 design has been retained and the connector is compatible with the original XT60, but now thanks to the snap on end cap there is no need to use heat shrink and the ridged edges on the end cap provide extra grip when pulling the male and female connectors apart.

Initial assembly requires a little force to clamp the end cap in place but please note that the end cap is hard to disassemble once it has been installed.  Should you wish to remove the end cap  you will have to "break it" with both hands to get it to release.  

These are genuine AMAAS connectors and are quality products, our customers should beware of imitations in the market that do not meet these standards.  

Specs:
Material: Gold-plated copper
External Material: Nylon/PA
Max. RC/MC: 60A/100A
Weight: 7.72g
Pulling Force/600: 3kg
Temperature Resistance: -20°C~120°C
Recommended Cable Spec.: 12AWG
Recommended Soldering Spec.: 480°C/4S

Includes:
5 sets of male and female plugs

IMPORTANT: "These are not cheap copied XT60 plugs. These original Nylon XT60 plugs, manufactured by AMASS, can handle over 60A current for extended periods without exceeding 80DegC thanks to their better contact surface area. The plug is also less likely to deform or melt in comparison to copied non-Nylon XT60 plugs."

The new XT60+ is here!  With "snap on" insulating end caps to provide the best polarity insulation for your soldered connections, these are sure to become the most popular battery connector for hobbyists.

The basis of the original robust XT60 design has been retained and the connector is compatible with the original XT60, but now thanks to the snap on end cap there is no need to use heatshrink and the ridged edges on the end cap provide extra grip when pulling the male and female connectors apart.

Initial assembly requires a little force to clamp the end cap in place but please note that the end cap is hard to disassemble once it has been installed.  Should you wish to remove the end cap  you will have to "break it" with both hands to get it to release.  

These are genuine AMAAS connectors and are quality products, our customers should beware of imitations in the market that do not meet these standards. 

Specs:
Material: Gold-plated copper
External Material: Nylon/PA
Max. RC/MC: 60A/100A
Weight: 7.72g
Pulling Force/600: 3kg
Temperature Resistance: -20°C~120°C
Recommended Cable Spec.: 12AWG
Recommended Soldering Spec.: 480°C/4S

Includes:
5 x male plugs

IMPORTANT: "These are not cheap copied XT60 plugs. These original Nylon XT60 plugs, manufactured by AMASS, can handle over 60A current for extended periods without exceeding 80DegC thanks to their better contact surface area. The plug is also less likely to deform or melt in comparison to copied non-Nylon XT60 plugs."

The new XT60+ is here!  With "snap on" insulating end caps to provide the best polarity insulation for your soldered connections, these are sure to become the most popular battery connector for hobbyists.

The basis of the original robust XT60 design has been retained and the connector is compatible with the original XT60, but now thanks to the snap on end cap there is no need to use heatshrink and the ridged edges on the end cap provide extra grip when pulling the male and female connectors apart.

Initial assembly requires a little force to clamp the end cap in place but please note that the end cap is hard to disassemble once it has been installed.  Should you wish to remove the end cap  you will have to "break it" with both hands to get it to release.  

These are genuine AMAAS connectors and are quality products, our customers should beware of imitations in the market that do not meet these standards. 

Specs:
Material: Gold-plated copper
External Material: Nylon/PA
Max. RC/MC: 60A/100A
Weight: 7.72g
Pulling Force/600: 3kg
Temperature Resistance: -20°C~120°C
Recommended Cable Spec.: 12AWG
Recommended Soldering Spec.: 480°C/4S

Includes:
5 x female plugs

IMPORTANT: "These are not cheap copied XT60 plugs. These original Nylon XT60 plugs, manufactured by AMASS, can handle over 60A current for extended periods without exceeding 80DegC thanks to their better contact surface area. The plug is also less likely to deform or melt in comparison to copied non-Nylon XT60 plugs." 

Landing Gear Wheel Stopper (10pcs)

To suit 3mm Shaft

Landing Gear Wheel Stopper (10pcs)
To suit 5mm Shaft

Linkage Stopper D2.1mm (10sets)

Scale wheels, split hub type, rubber "air" tyre, removable hub covers.

Size: 2in  D51×Φ4×H13mm

Weight: 19g Per Wheel

Warbird/Scale wheels, split hub type, rubber "air" tyre, removable hub covers.

Size:2.75in  D70×Φ4×H23mm

Weight: 55g Per Wheel

Warbird/Scale wheels, split hub type, rubber "air" tyre, removable hub covers.

Size: 4in  D102×Φ6×H26mm

Weight: 118g Per Wheel

Heavy duty control rods with ball link ends (2pcs/bag)

 Size：M4+M4×L83mm