Accessories

Getting wheel pants mounted to your undercart and getting them to stay there has been a problem for many years, not anymore, with the Sullivan adjustable brackets this job has now been made very much easier. The brackets are very strong, they are made of high strength heat treated steel, they can also be adjusted for "give" so that you do not damage the wheel pants on a heavy landing. These mounts will fit 3/16" (4.8mm) axles and music wire and the wheel pants can be either glued or bolted to the brackets.

Please note:  2 brackets are supplied but this is only enough for 1 wheel pant, you will require 2 packs for a standard 2 wheel undercart.

The MultiStar 1045 prop was made specifically for Mutli-Rotor use using a slot (DJI) style hub for proper centering and non-slip engagement. The Multistar line of props come in CW and matched CCW rotations and the center hubs are beefed up, so no fear of splitting the hub and tossing a blade! They also have a thicker cross-section to minimize flexing and increase their durability. The 1045’s precision molding will allow these props to require very little to no balancing. Multistar is simplifying the world of Multi-Rotors with their purpose built product line and taking the guess work out of your setup.

Specs:
Size: 10-4.5
rotation: CW
Hub: slot (DJI) style, 8mm bottom Dia  7mm flat to flat and drop down to 6mm top hole

Included:
Two CW Props

The Turnigy Electrical Switch is a rugged solid state switch that has no contacts to fail like traditional mechanical switches. It can work on 4~8 NiMh/NiCD cells or a 2S 7.4V Lipoly battery. It features a Lipo mode which offers low voltage protection to the battery should the pack dip below 6.0V. A LED voltage indicator gives you at a glance status of your receiver so you always know how much of your pack is left. The plastic case has two tabs molded in allow you to mount it easily to your airframe for nice clean installations.

Features:
• Momentary on/off switch
• Screw mounting tabs
• Connectors work with JR/Futaba type servo plugs
• LED voltage indicator
• Lipo mode has voltage cutoff to protect lipoly batteries from over-discharge

Specs:
Input Voltage: 4.8~10V (2S Lipoly, or 4~8 cell NiMh/NiCD)
Continuous Current: 8A
Max Burst Current: 14A (10 sec)
Size: 43x33x9mm
Weight: 9g
Connectors: Futaba (Works with JR)

Add a touch of professionalism to your scale RC Jet with the "OK Hand
Style" Jet pilot. Suitable for 90mm Class Jets.

Specs:
Height: 91mm
Width: 77mm
Depth: 45mm / 64mm (Incl. Hand)
Weight: 34g

Add a touch of professionalism to your scale RC Jet with the "OK Hand
Style" Jet pilot. Suitable for 90mm Class Jets.

Specs
Height: 91mm
Width: 77mm
Depth: 45mm / 64mm (Incl. Hand)
Weight: 34g

This small lightweight 4ch switch is extremely handy for auxillary functions on all sorts of models. Plug the single lead into an auxillary switched function then switch your radio on, channel 1 on the electronic switch will then be active, cycle the auxillary switch once and channel 1 goes out and channel 2 comes on, cycle the switch once more and 2 goes out and channel 3 comes and so on until it comes back to channel 1. When the radio is switched off and then switched back on the unit will default to channel 1 each time. This unit is great for switching lights on and off and other low current applications.

Please note: For this switch to work correctly you will need to set the related channel travel to +- 100%.

Specs:
Input Voltage: 4.8~7.4v
Output Voltage: 4.8~7.4v
Maximum Current: 2amps
Length: 40mm
Width: 20mm
Height: 12mm
Weight: 7g
Input Cable: 21cm (JR type plug)

Specs:
Maximum throughput : 10A / 30v
Weight: 7g

Very well made and finished lightweight alloy oleo struts with offset and trailing link, they are sprung loaded and will accept a wheel of up to 76mm (3ins) diameter.

Very well made and finished lightweight alloy straight oleo struts suitable for main undercarriages. These struts are sprung loaded which helps smooth out those slightly heavy arrivals.

Well made self tighening propellers, improve the performance of your multirotor with these efficient propellers.
The pack contains 1 x clockwise and 1 x counter clockwise rotating props. 

Specs:
Prop Size: 5 x 3.2ins
Pitch: 3.2
Mounting Thread: 5mm
Weight: 4g per blade
Rotation: 1 each L/H and R/H
Material: Nylon
Color: Black

Well made self tighening propellers, improve the performance of your multirotor with these efficient propellers.

The pack contains 1 x clockwise and 1 x counter clockwise rotating props. 

Specs:
Prop Size: 5 x 3.2ins
Pitch: 3.2
Mounting Thread: 5mm
Weight: 4g per blade
Rotation: 1 each L/H and R/H
Material: Nylon
Color: Red

Aluminum Folding Propeller Spinner 40mm Diameter w/5.0mm Shaft Adapter.

Dimensions as per image:
A: 39.8mm
B: 45.2mm
C: 5mm
D: 31mm
E: 3.75mm
F: 36.7mm
Blade Retaining Bolts: 3mm
Weight: 34g

Need to repair crash damage to a Multi-rotor flight board or add pin outs to any other electronics project?

These header pin blocks use the industry standard spacing of 2.54mm and are designed for soldering directly into printed circuit boards (PCB's). They are supplied in 30 pin lengths which can be easily cut to seperate individual pins.

There are 5 strips per pack.

Need to repair crash damage to a Multi-rotor flight board or add pin outs to any other electronics project?

These header pin blocks use the industry standard spacing of 2.54mm and are designed for soldering directly into printed circuit boards (PCB's). They are supplied in 30 pin lengths which can be easily cut to seperate individual pins.

There are 5 strips per pack.

Need to repair crash damage to a Multi-rotor flight board or add pin outs to any other electronics project?

These header pin blocks use the industry standard spacing of 2.54mm and are designed for soldering directly into printed circuit boards (PCB's). They are supplied in 30 pin lengths which can be easily cut to seperate individual pins.

There are 5 strips per pack.

Need to repair crash damage to a Multi-rotor flight board or add pin outs to any other electronics project?

This Header pin type is perfect for repairing Servo pins on most 4 (or more) channel receivers.

These header pin blocks use the industry standard spacing of 2.54mm and are designed for soldering directly into printed circuit boards (PCB's). They are supplied in 30 pin lengths which can be easily cut to seperate individual or groups of pins.

There are 5 strips per pack.

Ever damaged your model trying to separate difficult plugs? Frustrated by tight connectors? Turnigy to the rescue with their EasyOff Plug Disconnect system. These handy little clip-on adapters slip onto your T-plug connector and permanently stay in place. A special separator tool slips in between these clips, allowing you to effortlessly separate the plugs. It is a great addition for all your batteries or speed controls, but is very useful for tight battery hatch areas on airplanes and gliders.

The EasyOff plug adapters are universal fit between male and female plugs. They clip into place, though we recommend a small drop of CA glue for the ultimate hold. These are design for XT Branded T-plugs with molded grip detail.

This set includes the separator tool. Additional adapter sets for T-plugs are available here

Also available for XT-60

Specs:
Plug Type: T-Plug
Qty: 20
Weight: 0.9g (pair)

Ever damaged your model trying to separate difficult plugs? Frustrated by tight connectors? Turnigy to the rescue with their EasyOff Plug Disconnect system. These handy little clip-on adapters slip onto your T-plug connector and permanently stay in place. A special separator tool slips in between these clips, allowing you to effortlessly separate the plugs. It is a great addition for all your batteries or speed controls, but is very useful for tight battery hatch areas on airplanes and gliders.

The EasyOff plug adapters are universal fit between male and female plugs. They clip into place, though we recommend a small drop of CA glue for the ultimate hold. These are design for XT Branded T-plugs with molded grip detail.

This set does not include the separator tool. Adapters with the separator tool included can be found here

Also available for XT-60

Specs:
Plug Type: T-plug
Qty: 20
Weight: 0.9g (pair)

Many connectors are small and diffucult to grip. Especially if you have oil or grime on your hands. Turnigy makes life easier with their BigGrip connector adapters. These handy adapters mount to your XT-60 and give you a textured, larger surface area to grip the connector when disconnecting power. This saves you frustration, and eliminates any need to tug on the wires themselves. Each adapter is two pieces, and is attached using a small dab of glue.

We suggest a silicone type sealant glue as this makes the adapter semi-removable without damaging the plastic of the plug should you ever need to service a solder joint.

This set is for XT-60 Males.

Also available as:
XT-60 Female
XT-60 Male/Female Set

Specs:
Plug Type: XT-60 Male
Qty: 6 pieces
Weight: 3g

 

Many connectors are small and diffucult to grip. Especially if you have oil or grime on your hands. Turnigy makes life easier with their BigGrip connector adapters. These handy adapters mount to your XT-60 and give you a textured, larger surface area to grip the connector when disconnecting power. This saves you frustration, and eliminates any need to tug on the wires themselves. Each adapter is two pieces, and is attached using a small dab of glue.

We suggest a silicone type sealant glue as this makes the adapter semi-removable without damaging the plastic of the plug should you ever need to service a solder joint.

This set is for XT-60 Females.

Also available as:
XT-60 Male
XT-60 Male/Female Set

Specs:
Plug Type: XT-60 Female
Qty: 6 pieces
Weight: 3g

 

Many connectors are small and diffucult to grip. Especially if you have oil or grime on your hands. Turnigy makes life easier with their BigGrip connector adapters. These handy adapters mount to your XT-60 and give you a textured, larger surface area to grip the connector when disconnecting power. This saves you frustration, and eliminates any need to tug on the wires themselves. Each adapter is two pieces, and is attached using a small dab of glue.

Many connectors are small and diffucult to grip. Especially if you have oil or grime on your hands. Turnigy makes life easier with their BigGrip connector adapters. These handy adapters mount to your T-Plug and give you a textured, larger surface area to grip the connector when disconnecting power. This saves you frustration, and eliminates any need to tug on the wires themselves. Each adapter is two pieces, and is attached using a small dab of glue.

We suggest a silicone type sealant glue as this makes the adapter semi-removable without damaging the plastic of the plug should you ever need to service a solder joint.

This set is for T-Plug Males.

Also available as:
T-Plug Female
T-Plug Male/Female Set

Specs:
Plug Type: T-Plug Male
Qty: 6 pieces
Weight: 3g

 

Many connectors are small and diffucult to grip. Especially if you have oil or grime on your hands. Turnigy makes life easier with their BigGrip connector adapters. These handy adapters mount to your T-Plug and give you a textured, larger surface area to grip the connector when disconnecting power. This saves you frustration, and eliminates any need to tug on the wires themselves. Each adapter is two pieces, and is attached using a small dab of glue.

We suggest a silicone type sealant glue as this makes the adapter semi-removable without damaging the plastic of the plug should you ever need to service a solder joint.

This set is for T-Plug Females.

Also available as:
T-Plug Male
T-Plug Male/Female Set

Specs:
Plug Type: T-Plug Female
Qty: 6 pieces
Weight: 3g

 
 

Many connectors are small and diffucult to grip. Especially if you have oil or grime on your hands. Turnigy makes life easier with their BigGrip connector adapters. These handy adapters mount to your T-Plug and give you a textured, larger surface area to grip the connector when disconnecting power. This saves you frustration, and eliminates any need to tug on the wires themselves. Each adapter is two pieces, and is attached using a small dab of glue.

We suggest a silicone type sealant glue as this makes the adapter semi-removable without damaging the plastic of the plug should you ever need to service a solder joint.

This set is for T-Plug Females/Male

Also available as:
T-Plug Male
T-Plug Female

Specs:
Plug Type: T-Plug Female/Male
Qty: 12 pieces (6 Male, 6 Female)
Weight: 3g

M2 All Thread Rod 300mm (2 pieces) Great for custom control rods or other DIY projects

The cable tie clip mounting set is the perfect solution for the modeller who likes a neat and tidy install. The clips provide slots for cable ties up to 4mm width and can be simply glued in onto the desired position within your model.

The clips are suitable for fiberglass, foam or wooden models but can be used for almost any application.     

Specs:
Material: ABS Plastic
Weight Per Set: 11g
Fits: 4mm cable ties

The Turnigy glider bag backpack is great for securely carrying your glider to a remote slope location, where your parking area is far from your flying area. Just strap it to your back and go! Made of durable 600 denier nylon, this wing bag is designed to handle every day use for years to come.

A main compartment holds your wings and fuselage, while a separate compartment holds your transmitter or other accessories. There is even a compartment designed specifically to hold your wing tubes. The compartments are closed with drawstrings and the shoulder straps adjust to fit any size person.

Perfect for 2 meter or larger sailplanes. For smaller sailplanes take a look at our smaller Turnigy Glider Backpack

Specs:
Main Compartment Size: 1300 x 310 x 70mm
Accessory Compartment Size: 200 x 170 x 120mm

Avios Hawker Sea Fury 1200mm - Propeller Set

Includes:
5-Blade Hub
5 * Propeller Blades
5 * Screw
5 * Locknut

*NOTE - this propeller is for static display only. It is not intended to be used for the purposes of propelling the aircraft to fly. 

These handy wicks are great for lighting the smoke cartridges, each one will burn continously for 30mins.

HXT 4mm Connector to T-plug conversion charge lead

This will connect to a Lipo fitted with HXT 4mm connectors and a charge lead fitted with a T-plug

15x5.2 Folding Carbon Fiber Propeller Blades for DJI S800 Evo (2 pairs L/H & R/H Rotation).

Well made folding carbon fiber propeller blades for the DJI S800 Evo, improve the performance of your S800 with these very efficient propellers.

Specs:
Diameter: 15ins
Pitch: 5.2ins
Mounting Hole: 3mm
Mounting Hub Thickness: 4.15mm
Weight: 7.5g per blade
Rotation: 1 pair of each L/H and R/H
Material: 3K plain weave carbon fiber
Color: Black

The Quanum series of carbon fiber propellers have been specially designed for multi-rotors and are manufactured to very exacting standards. They are extremely light and strong and you can expect an increase in performance due to their ultra thin and stiff carbon construction.

As supplied these propellers are ready to fit a 6mm shaft but this can be reamered to suit shafts up to 10mm, adapters for a 5mm shaft are also included.

Specs:
Length: 14 inch
Pitch: 4.7 inch
Mounting Hole Diameter: 6mm
Hub Thickness: 7.5mm
Weight: 24g each
Rotation: Clockwise and counterclockwise

The Quanum series of carbon fiber propellers have been specially designed for multi-rotors and are manufactured to very exacting standards. They are extremely light and strong and you can expect an increase in performance due to their ultra thin and stiff carbon construction.

These propellers are specifically designed for DJI multirotors that have the ability to perform 3D flight, they will perform equally well whichever way up the multi-rotor is.

The props have a center hole of 8mm which suits DJI multirotors.

Specs:
Length: 8 inch
Pitch: 6 inch
Center Hole: 8mm
Hub Thickness: 10mm
Weight: 8g each
Rotation: Clockwise and counterclockwise

These nicely made carbon propellers have been designed specifically for large multi-rotors. They will make transportation much easier by allowing you to fold the blades back to the boom arms, much like transporting an RC helicopter.

Carbon propellers are much stiffer and lighter than conventional type blades which means you will instantly see an increase in performance. These blades are supplied as a set, which means you get 1 pair of clockwise rotation blades and 1 pair of counter-clockwise blades.

Specs:
Diameter: 17 inches
Pitch: 6 inches
Hub Thickness: 5mm
Bolt Hole: 3mm
Material: Carbon fiber
Weight: 13g (each blade)
Rotation: Clockwise and counter-clockwise