$5 - $9.99

Arduino 6-DOF IMU Module Attitude Control 6DOF 3205 345

*Note: This is not an original Arduino brand product.

The Arduino Relay module allows a wide range of microcontrollers such as Arduino, AVR ,PIC, ARM with digital outputs to control larger loads and devices like AC or DC Motors, electromagnets, solenoids, and incandescent light bulbs. This relay shield uses QIANJI JQC-3F high-quality relays with rated load 7A/240VAC,10A/125VAC,10A/28VDC. The relay output state is individually indicated by a light-emitting diode.

Specs:
Dimensions: 99x70x18mm
Weight: 88g

*Note: This is not an original Arduino brand product.

The flight mode switcher has been designed for open source autopilots such as APM, PX4 and Pix etc. It can switch the flight mode accurately and quickly and replaces the troublesome 2 stage and 3 stage switchers.

Users can set the parameters for the flight mode switcher on the unit and choose the most suitable modes for their requirements. The flight mode switcher features a stable performance, is easy to set up and is small and lightweight.

Typical flight modes are as follows:
• STA (Stabilized) Model will automatically level itself
• SIM (Simple) Allows you to control the movement of the model from the pilots point of view regardless of which way the model is facing
• ALT (Altitude Hold) When this mode is selected it will hold this altitude
• LOI (Loiter) Allows model to hover in the same spot on its own without any input from the pilot
• AUT (Auto) The model will follow a pre-programmed course stored in the autopilot
• RTL (Return to land) Once selected the model will return and land at the point of take-off

The flight mode switcher is simple to install on your transmitter but it is not "plug & play", there is a small amount of soldering involved inside the Tx. See under the "Files" tab for installation instructions.

Once installed on your transmitter and set up in "Mission Planner" it is very simple to use, just press the relevant mode button on the switcher and the model will go into that mode. There is an indicator light to show which mode has been selected and is in use.

Features:
• Allows the user to easily set 6 flight modes
• Simple and straightforward to install
• Compact and lightweight
• Status indicator lights

Specs:
Type: Flight Mode Switcher
Working Voltage: 3~5V
Modes: 6 selectable
Operating Temperature: -10°C~+60°C
Dimensions: 59 x 29 x 9.3mm
Weight: 13g

Included:
Flight Mode Switcher
Connection harness

Front One Way Version 2 Turnigy TD10 4WD Touring Car (1 set)

A good quality, strong, easy-to-use, iron-on plastic film covering with good shrinking properties that is suitable for most RC model airplanes.

Specs:
Material: Plastic film
Color: Small red/white chequered pattern
Adhesive: Heat-activated
Width: 638mm
Quantity: 5 meters

Please note: Parcel weight includes special tube packaging.

The flying V is perhaps the best general purpose antenna in the lower frequencies. Suitable for medium range and altitude, this antenna has slightly lower gain verses the coaxial connected Dipole, however has a very uniform radiation pattern. This is perfect for acrobatic and sport flying where antenna polarization (angle) can vary. The 120 deg V gives the best compromise between radiation pattern and gain.

Specs:
Frequency: 1.3GMHz
Connection: RP-SMA
dbi: 1.9

Specs.
Length: 199mm
Thickness: 3.3mm
Width: 18mm
Weight: 19g

Carbon fiber tail wheel brackets add good looks, strength, and most importantly, keep excess weight out of the tail of your airplane. Made from 3K Carbon cloth, these brackets are light and strong. Comes un-drilled so it can suit a wide variety of models. Drill dimple marks are molded in for easy drilling.

Suited for models up to 120cc sized models.

Specs:
Length: 170mm
Width: 12mm
Weight: 9g

TURNIGY Programming Card

For use with Turnigy Plush ESCs (exc Plush-32)

This device plugs inbetween the Rx and the speed controller. It allows the user to program the BESC according to a series of LED indicators.
it has buttons at the bottom so you can navigate through the menu and select the feature you want, then change it. Its very simple and is much easier than listening to jingles or a series of beeps.

This item is an excellent addition to your flight kit, especially with the new hard plastic case and lets you quickly change the BESCs settings in the field in a much shorter time and with greater assurance that what you have changed is correct and saved into the BESC.

No more black magic throttle stick programming!
Throw away the manual, you wont need it anymore!

Compatible with Turnigy Plush speed controllers but NOT the Plush-32 ESC's.

Full Alloy Metal Steering Knuckle Arms L/R - A2038 & A3015 (1pair)

One Way Ball Bearing - Trooper Nitro

This is a great way to avoid power shorts.
Rated to around 120A

Gold connectors on their own are notorious for creating a short circuit and looking messy. Use these to keep your connections safe and looking neat!
 
Easier to solder and a stronger connection than Deans T-plugs

4mm Gold Plated Banana Plug (10pc)

Specs:
Model: TGY-225MG
Voltage: 4.5 - 6v
Speed: .12s
Running Current: 180mA
Torque: 3.5kg/cm
Gears: Metal
Weight: 26g
Spline Count : 21 Tooth

Narrow dead band width.

The Vortex FPV Racer from ImmersionRC is an incredible piece of kit for the serious competitor, but like all things flying the ocassional mishap is inevitable!

This crash kit is a convenient way to keep a stock of all of those plastic parts most likely to be damaged in a serious "departure from controlled flight"

Included are all parts which mount the motors to the carbon fiber arms, the plastic pivot points, foldable arm clips, and all other plastic parts.

No carbon fiber parts are included (see Crash Kit 2.)

Included:
1 x Front bumper (FR4)
2 x Side plates
8 x Arm clips
4 x Arm pivot tops
4 x Arm pivot bottoms
4 x Landing bumpers
4 x Landing mounts
4 x Motor mounts
8 x Hex bushes
1 x Camera support base
1 x Camera support arm
4 x Damper pins
4x Damper circlip
4x Screw HA2x8
4x Screw HA2x6

Get an unfair advantage with Turnigy Nano-tech Airsoft Packs!

On the battlefeild, no one wants to compromise on fire power! That's why the legendary Turnigy nano-tech batteries are available as a drop-in replacement pack for an upgrade in firepower. 

Turnigy Nano-tech Airsoft batteries are superior to the standard NiMH batteries offering faster charge rates and higher voltages. In short, the first thing your opponent will notice is sustained rapid fire pinning him down.

It's clear why Turnigy Nano-techs are the go to pack for anyone who is serious about Airsoft.

Spec.
Capacity: 2000mAh
Voltage: 3S1P / 3S Cell / 11.1V
Discharge: 15C Constant / 25C Burst
Weight: 155g (including wire, plug & case)
Dimensions: 126x21x29mm 
Balance Plug: JST-XH
Discharge Plug: Mini-Tamiya (Mini Molex) 

Advantages over traditional Lipoly batteries;
• Power density reaches 7.5 kw/kg.
• Less Voltage sag during high rate discharge, giving more power under load.
• Internal impedance can reach as low as 1.2mO compared to that of 3mO of a standard Lipoly.
• Greater thermal control, pack usually doesn’t exceed 60degC
• Swelling during heavy load doesn’t exceed 5%, compared to 15% of a normal Lipoly.
• Higher capacity during heavy discharge. More than 90% at 100% C rate.
• Fast charge capable, up to 15C on some batteries.
• Longer Cycle Life, almost double that of standard lipoly technology.

The nano-core technology in lithium ion batteries is the application of nanometer conductive additives. The nanometer conductive additives form ultra-strong electron-conducting networks in the electrodes which can increase electronic conductivity.

These additives create the ability for imbibition in the carrier liquid to supply more ion channels.This improves the ability of ion transmission and ion diffusion. Through improving electronic conductivity and ion transmission, the impedance is reduced and the polarization of high rate discharge decreases greatly.

*Note: The length of Balance charging wire may vary

Get an unfair advantage with Turnigy Nano-tech Airsoft Packs!

On the battlefield, no one wants to compromise on firepower! That's why the legendary Turnigy nano-tech batteries are available as a drop-in replacement pack for an upgrade in firepower. 

Turnigy Nano-tech Airsoft batteries are superior to the standard NiMH batteries offering faster charge rates and higher voltages. In short, the first thing your opponent will notice is sustained rapid fire pinning him down.

It's clear why Turnigy Nano-techs are the go-to pack for anyone who is serious about Airsoft.

Spec.
Capacity: 2000mAh
Voltage: 3S1P / 3S Cell / 11.1V
Discharge: 15C Constant / 25C Burst
Weight: 162g (including wire, plug & case)
Dimensions: 125x10x21.5mm (Each)
Balance Plug: JST-XH
Discharge Plug: Mini-Tamiya (Mini Molex) 

Advantages over traditional Lipoly batteries;
• Power density reaches 7.5 kw/kg.
• Less Voltage sag during high-rate discharge, giving more power under load.
• Internal impedance can reach as low as 1.2mO compared to that of 3mO of a standard Lipoly.
• Greater thermal control, pack usually doesn’t exceed 60degC
• Swelling during heavy load doesn’t exceed 5%, compared to 15% of a normal Lipoly.
• Higher capacity during heavy discharge. More than 90% at 100% C rate.
• Fast charge capable, up to 15C on some batteries.
• Longer Cycle Life, almost double that of standard lipoly technology.

The nano-core technology in lithium ion batteries is the application of nanometer conductive additives. The nanometer conductive additives form ultra-strong electron-conducting networks in the electrodes which can increase electronic conductivity.

These additives create the ability for imbibition in the carrier liquid to supply more ion channels.This improves the ability of ion transmission and ion diffusion. Through improving electronic conductivity and ion transmission, the impedance is reduced and the polarization of high rate discharge decreases greatly.

Alu Undercarriage (1pair/bag)

Size:255mm 
Weight: 108g / pair

The HobbyKing helicopter pitch gauge is made from ultra-rigid fiberglass board and features dual ball bearings to ensure accurate measurements every time. This pitch gauge is supplied in kit form to keep production costs down which means we can pass the savings on to you!

Specs:
Measurement: +/- 20 Deg
Size: 145mm x 105mm
Max Blade Width: 80mm

Note: An assembly guide can be found in the FILES tab below.

Super Kinetic - Replacement Brushless Motor (2630-KV1000)

HobbyKing™ Bix3 Trainer 1550mm - Replacement Motor 2630 1400kv

HobbyKing™ Wingnetic 805mm - Replacement Fuselage

Excellent Quality Nylon Spinner with Lightened Alloy Backplate 63mm Red - Mount hole 6mm

Excellent Quality Nylon Spinner with Lightened Alloy Backplate 75mm White - Mount hole 8mm

Weight: 59g

Excellent Quality Nylon Spinner with Lightened Alloy Backplate 75mm Yellow - Mount hole 8mm

TURNIGY XK motors are without question one of the best motors on the market today. It all starts in our very own factory where we install precision bearings, correctly rated magnets, balanced rotors, tool-steel shafts and stators that are wound by hand. We rigorously test each and every component at 14 critical points during construction, testing everything from materials all the way through to final performance tests.

Progressive Shock system for BT-4 gives a progressive dampening effect through the shock travel so the effect is softest at the start and harder at the end. Includes blank shock pistons so you can drill your own holes for precise tuning to your individual needs.

Specs:
Length: 14mm
Diameter: 11mm
Piston: 10mm x 2mm

Turnigy TGY-AN13 analog car servo suitable for 1:8 & 1:10 scale cars with a tough, metal geartrain.

Supplied with a full hardware pack.

Specs:
Torque: 13.2kg/cm (4.8V)~14.5kg/cm (6.0V)
Speed: 0.15sec/60deg (4.8V)~0.13sec/60deg (6.0V)
Voltage: 4.8~6.0V
Type: Analog
Gear Train: Metal
Plug: JR type
Size: 40 x 37.5 x 20mm
Weight: 58g
Spline Count: 25

Durafly® ™ Tundra - Decal Set 

Perfect for snorkeling, diving, surfing or any other water based activity where you want to use your Gopro Hero 4 Session to capture the action.  

Made of clear heavy duty plastic, the housing has been designed to allow funtional control of the camera and comes with a heavy duty rubber seal that provides the housing with a depth rating of 40 metres.

Specs:
Material: Heavy duty clear plastic
Weight: 55g
Dimensions: 48 x 48 x 46mm