Bargain Bin

Each cell is hand-picked and matched for the ultimate in quality to deliver the power, durability and run time needed for the high performance models of today. Each pack is checked and tested at each stage of assembly to guarantee the highest possible quality. This careful matching and checking process allows the packs to achieve a mind boggling discharge rate of up to 140C. If you're the discerning racer or hardcore basher that needs to squeeze every last drop of performance out of your batteries, this is the pack for you!

Alloy Oleo Set Twin Nosewheel/Stirrup Mains for 90mm EDF/1.20 Class 3pc - Superb looking and high quality Oleo leg's for Warbirds and scale models & Jet's, complete with axles, wheel spacers and steel mounting pins.

Specs:
Length to axle centreline Mains: 125mm (not inc pin)
Length to axle centreline Noseleg: 115mm (not inc pin)
Retract Mounting Pin: 5mm
Axle: 4mm
Maximum Wheel Diameter Main: 70mm (20mm Wide)
Weight: 138g

Phantom FPV Flying Wing 1550mm - Replacement Motor Cover

The Pro Mini is a microcontroller board based on the ATmega328. It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, an on-board resonator, a reset button, and holes for mounting pin headers. A six pin header can be connected to an FTDI cable or breakout board to provide USB power and communication to the board.
 
The Pro Mini is intended for semi-permanent installation in objects or exhibitions. The board comes without pre-mounted headers, allowing the use of various types of connectors or direct soldering of wires. The pin layout is compatible with the Arduino Mini.

Mini USB Adapter (included):
This board converts a USB connection into 5 volt TX and RX signals that you can connect straight to the Arduino Mini or other microcontrollers, allowing them to talk to the computer. It is based on the FT232RL chip from FTDI (drivers are included with the Arduino software).

Features:
• ATmega328 running at 8MHz with external resonator (0.5% tolerance)
• USB connection off board
• Supports auto-reset
• 3.3V regulator
• Max 150mA output
• Over current protected
• Reverse polarity protected
• DC input 3.3V up to 12V
• On board Power and Status LEDs

Specs:
Operating Voltage: 3.3V
Input Voltage: 3.35 -12V
Digital I/O Pins: 14 (of which 6 provide PWM output)
Analog Input Pins: 6
DC Current per I/O Pin: 40mA
Flash Memory: 16KB (of which 2 KB used by bootloader)
SRAM: 1KB
EEPROM: 512 bytes
Clock Speed:  8MHz
Dimensions: 18x33mm
Weight: 2.3g

Includes:
1 x Pro Mini Microcontroller
1 x Mini USB Adapter

*Note: This is not an original Arduino brand product.

USBtinyISP V2.0 (Arduino-Compatible) is an ISP downloader for AVR microcontrollers based on the USB interface. It can be used for most AVR microcontrollers to download programs. In Arduino IDE, USBtinyISP is a downloader that is supported at all times, making it simple and convenient to use.

Specs:
Dimensions: 49x48x12mm
Weight: 17.3g

*Note: This is not an original Arduino brand product.

This is a great “bread board” pin ready accelerometer for your Arduino or other microcontroller projects

Features:
• BMA180 three-axis ultra-high performance digital accelerometer, which provides a 14-bit digital output via a 4-wire SPI or 2-wire I 2 C interface
• Full scale measurement range can be set to ± 1g balance, 1.5G, 2G, 3G, 4G, 8G or 16G
• programmable wake-up
• Low-g and high-g detection
• Tap detection
• Slope detection
• Self-test capability
• The sensor also has two operating modes: low noise, low power consumption in a tiny 3x3mm 12-pin LGA package BMA180
• The sensor can be between 1.62 to 3.6V VDD and 1.2 to 3.6V VDDIO supply will typically only consume 650uA standard mode.

Specs:
Size: 21 x 10 x 2.6mm
Voltage: 1.2-3.6v
Output: SPI or I2C

*Note: This is not an original Arduino brand product.

Superheterodyne 3310 Wireless receiver module +315RF Wireless transmitter module 

The Kingduino Pro 328 is a 5V/16MHz board running the 16MHz bootloader in a miniature form factor that will fit easily into your next small project.

The Pro 328 does not come with connectors, allowing you to solder in any connector or wire in any orientation required and is recommended for users who understand the limitations of this lack of connectors and USB off board.

The compact size is helped by having the DC power jack footprint available, but without hardware attached. This allows you to decide how best to utilize this function.

This board connects directly to the FTDI Basic Breakout board and supports auto-reset. The Kingduino Pro 328 also works with the FTDI cable but the FTDI cable does not bring out the DTR pin so the auto-reset feature will not work. In this latest version of the Kingduino Pro we’ve also moved the FTDI headers back so that the pins don’t hang over the edge of the board. We’ve also populated it with a sturdier power selection switch.

Features:
• USB connection off board
• 5V regulator
• Over current protected
• Reverse polarity protected
• DC input
• Resettable fuse prevents damage to board in case of short
• Power select switch acts as on/off switch

Specs:
Microcontroller: ATmega328
Clock Speed: 16MHz
Input Voltage: 5 ~ 12V DC
Max output: 150mA
Dimensions: 54 x 52mm

*Note: This is not an original Arduino brand product.

Arduino MEGA ProtoShield V3 prototype expansion board (including the bread board)

This is the latest Arduino MEGA ProtoShield V3 prototype expansion board with Immersion Gold PCB processing technology. The motherboard gold square pad spacing is small and features SOP28 SMD component packaging, perfect for Arduino electronics enthusiasts. 

This board can not only seamlessly be plugged into the Arduino MEGA controller, components can be soldered directly. To complete a variety of circuits, this board features an integrated power indicator, status lights and reset buttons.

Specs:
Dimensions: 103x56x19mm
Weight: 39.7g (w/bread board)

*Note: This is not an original Arduino brand product.

The LM35 Linear Temperature Sensor Module can be used to detect ambient air temperature. This sensor offers a functional range between -40 degree Celsius to 150 degree Celsius. Sensitivity is 10mV per degree Celsius. The output voltage is proportional to the temperature. It is commonly used as a temperature measurement sensor. It includes thermocouples, platinum resistance, thermal resistance and temperature semiconductor chips, which are commonly used in high temperature measurement thermocouples. Platinum resistance temperature used in the measurement of 800 degrees Celsius, while the thermal resistance and semiconductor temperature sensor suitable for measuring the temperature of 100-200 degrees or below, in which the application of a simple semiconductor temperature sensor has good linearity and high sensitivity. The LM35 linear temperature sensor and sensor-specific expansion of Arduino board, in combination, can be very easy to achieve.

Specs:
Sensitivity: 10mV per degree
Celcius Functional range: -40 degree Celsius to 150 degree Celsius

*Note: This is not an original Arduino brand product.

Arduino 6-DOF IMU Module Attitude Control 6DOF 3205 345

*Note: This is not an original Arduino brand product.

Arduino 10DOF with ITG-3205, ADXL345, HMC5883L, and BMP085

*Note: This is not an original Arduino brand product.

The Arduino Relay module allows a wide range of microcontrollers such as Arduino, AVR ,PIC, ARM with digital outputs to control larger loads and devices like AC or DC Motors, electromagnets, solenoids, and incandescent light bulbs. This relay shield uses QIANJI JQC-3F high-quality relays with rated load 7A/240VAC,10A/125VAC,10A/28VDC. The relay output state is individually indicated by a light-emitting diode.

Specs:
Dimensions: 99x70x18mm
Weight: 88g

*Note: This is not an original Arduino brand product.

Keep your Telemetry Radios safe! These cases are made out of slightly translucent ABS plastic, so you still can see TX/RX LEDs. They have a very tight fit and finish and are clearly labeled. These cases will make your setup look like Pro gear, while keeping them safe!

Designed to fit FPV Radio Telemetry Kit - 915Mhz/433MHz(#42846/42847,not included), But fits other brand Telemetry Radios as well.

Includes:
3M Foam Double-tape X1
Ground module Case X1
Air module Case X1

The flight mode switcher has been designed for open source autopilots such as APM, PX4 and Pix etc. It can switch the flight mode accurately and quickly and replaces the troublesome 2 stage and 3 stage switchers.

Users can set the parameters for the flight mode switcher on the unit and choose the most suitable modes for their requirements. The flight mode switcher features a stable performance, is easy to set up and is small and lightweight.

Typical flight modes are as follows:
• STA (Stabilized) Model will automatically level itself
• SIM (Simple) Allows you to control the movement of the model from the pilots point of view regardless of which way the model is facing
• ALT (Altitude Hold) When this mode is selected it will hold this altitude
• LOI (Loiter) Allows model to hover in the same spot on its own without any input from the pilot
• AUT (Auto) The model will follow a pre-programmed course stored in the autopilot
• RTL (Return to land) Once selected the model will return and land at the point of take-off

The flight mode switcher is simple to install on your transmitter but it is not "plug & play", there is a small amount of soldering involved inside the Tx. See under the "Files" tab for installation instructions.

Once installed on your transmitter and set up in "Mission Planner" it is very simple to use, just press the relevant mode button on the switcher and the model will go into that mode. There is an indicator light to show which mode has been selected and is in use.

Features:
• Allows the user to easily set 6 flight modes
• Simple and straightforward to install
• Compact and lightweight
• Status indicator lights

Specs:
Type: Flight Mode Switcher
Working Voltage: 3~5V
Modes: 6 selectable
Operating Temperature: -10°C~+60°C
Dimensions: 59 x 29 x 9.3mm
Weight: 13g

Included:
Flight Mode Switcher
Connection harness

Front One Way Version 2 Turnigy TD10 4WD Touring Car (1 set)

Replacement Rear Crankshaft Bearing for NGH GT35 and GT35R Gas Engines.

NGH GT25/GF38 Gas Engines Replacement Crankshaft Front Bearing

Specs:
Outlet Diameter: 26mm
Inner Diameter: 10mm
Width: 8mm
Type: Sealed

A good quality, strong, easy-to-use, iron-on plastic film covering with good shrinking properties that is suitable for most RC model airplanes.

Specs:
Material: Plastic film
Color: Small red/white chequered pattern
Adhesive: Heat-activated
Width: 638mm
Quantity: 5 meters

Please note: Parcel weight includes special tube packaging.

Alu. Stabilizer Holder - 1/10 Hobbyking Mission-D 4WD

Circular polarized antenna's aka "clover leaf antennas" are a great way to increase the performance of your FPV system. The circular polarization helps reject “multipath interference”, a problem that plagues standard dipole stock antennas. Proven to increase range and video clarity, circular polarized antennas have become the standard after-market 'essential' upgrade for modern FPV systems. This is a matched 3 leaf Tx to 4 leaf RX set with no cable length for a nice clean, direct install with RP-SMA connectors.

Specs:
Frequency Range: 900MHz
Impedance: 50ohm
VSWR: <1.5
Gain: 5db
Connector: RP-SMA
Cable: RG141
Cable Length: 0m

The flying V is perhaps the best general purpose antenna in the lower frequencies. Suitable for medium range and altitude, this antenna has slightly lower gain verses the coaxial connected Dipole, however has a very uniform radiation pattern. This is perfect for acrobatic and sport flying where antenna polarization (angle) can vary. The 120 deg V gives the best compromise between radiation pattern and gain.

Specs:
Frequency: 1.3GMHz
Connection: RP-SMA
dbi: 1.9

Specs.
Length: 199mm
Thickness: 3.3mm
Width: 18mm
Weight: 19g

This 2 piece carbon fiber landing gear is lightweight but very stiff and with high torsional strength, the legs are also streamlined to reduce drag. Designed for fuselages with a minimum width of 170mm, however the legs can be spaced apart to fit aircraft with a much wider fuselage. 

Specs:
Fuselage Width: 170mm
Height: 280mm
Wheel Track: 580mm
Weight: 315g

Carbon fiber tail wheel brackets add good looks, strength, and most importantly, keep excess weight out of the tail of your airplane. Made from 3K Carbon cloth, these brackets are light and strong. Comes un-drilled so it can suit a wide variety of models. Drill dimple marks are molded in for easy drilling.

Suited for models up to 80cc sized models.

Specs:
Length: 118mm
Width: 14.2mm
Weight: 7.5g

Carbon fiber tail wheel brackets add good looks, strength, and most importantly, keep excess weight out of the tail of your airplane. Made from 3K Carbon cloth, these brackets are light and strong. Comes un-drilled so it can suit a wide variety of models. Drill dimple marks are molded in for easy drilling.

Suited for models up to 120cc sized models.

Specs:
Length: 170mm
Width: 12mm
Weight: 9g

Super tough glass fiber tube, perfect for fixed wing and multi rotor projects. 

Specs:
Outer Diameter: 8mm
Bore Diameter 5mm
Length: 330mm

Aluminum alloy neck strap adjuster suitable for DJI transmitters or similar.

2mm 2 Blade CNC Folding Propeller Adapter CW & CCW (Gold)

Perfect for multi-rotors, pack comes complete with M2.5 mounting screws for the folding propeller blades.

Specs:
Suits Motor Shafts: 2mm
Blade Thickness: 3mm
Blade Mounting: M2.5
Direction: 1 x Clockwise, 1 x Counterclockwise
Material: Aluminum
Color: Gold
Weight: 6g each

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 10g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 10g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3.17mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)