$5 - $9.99

Designed in-house by HobbyKing, this Turnigy parallel charge board can charge up to 6 LiPo or LiHV packs of the same capacity and cell count at the same time. The board is supplied with TR connectors for the main charging leads, a pair of 4mm banana plugs to connect to the charger, and 2~6S JST-XH connectors for the balancing leads. The board is fused for protection and a 6S JST-XH adaptor lead is also supplied to connect the board to your charger balancing input.

Designed in-house by HobbyKing, this Turnigy parallel charge board can charge up to 6 LiPo or LiHV packs of the same capacity and cell count at the same time. The board is supplied with EC3 connectors for the main charging leads, a pair of 4mm banana plugs to connect to the charger, and 2~6S JST-XH connectors for the balancing leads. The board is fused for protection and a 6S JST-XH adaptor lead is also supplied to connect the board to your charger balancing input.

This next-generation bidirectional cross weave glass fiber reinforcing tape has a transparent "PET" substrate which provides a high longitudinal tensile strength, and is transverse tear resistance, in short, it is extremely strong. The other outstanding property it has is the adhesive, it is super sticky, but allows for positioning. Once you are satisfied with the position of the tape gently apply more pressure and the strength of the bond increases. This strong, pressure-sensitive rubber-based adhesive will also increase its strength over the next 24hrs as it "cures" to form a permanent, very strong bond. Another characteristic of this tape is that it will retain its strength in high and low temperatures.

Model: TGY-1501MG
Voltage: 4.8~6.0v
Speed: 0.16~0.14sec
Torque: 15.5~17.0kg/cm
Weight: 60g
Size: 40.7x20.5x39.5mm
Spline Count: 25

Specs:
Model: TGY-225MG
Voltage: 4.5 - 6v
Speed: .12s
Running Current: 180mA
Torque: 3.5kg/cm
Gears: Metal
Weight: 26g
Spline Count : 21 Tooth

Narrow dead band width.

Turnigy TGY-AN13 analog car servo suitable for 1:8 & 1:10 scale cars with a tough, metal geartrain.

Supplied with a full hardware pack.

Specs:
Torque: 13.2kg/cm (4.8V)~14.5kg/cm (6.0V)
Speed: 0.15sec/60deg (4.8V)~0.13sec/60deg (6.0V)
Voltage: 4.8~6.0V
Type: Analog
Gear Train: Metal
Plug: JR type
Size: 40 x 37.5 x 20mm
Weight: 58g
Spline Count: 25

Spare Part - Premium BNC 1.3m RG223 cable for Scherrer Rx700LR Long Range UHF system

Reliably monitor the voltage of your battery with the Turnigy TGY-CVT01 Voltage Sensor.

As a great alternative to setting a timer, fly or drive your model based on the actual voltage of your battery. This way if your voltage drops quicker than usual due to harder running, you can avoid over discharge your pack. Or, perhaps you're having a nice relaxed day? Enjoy longer run times and don't cut yourself short.

This small, compact sensor is also a perfect way to add piece of mind when running a high performance model by allowing you to check that the battery voltage isn't dropping excessively under load.

For use with the TGY- i10 and i6 transmitters and TGY-iA10 and i6 V2 receivers.

Designed to daisy chain together with other TGY-C series sensors.

Features:
• High quality, compact sensor
• Futaba style input and output connectors
• Great for monitoring battery voltage, no need to set timers anymore
• Works with TGY- i10 and i6 transmitters and TGY-iA10 and i6 V2 receivers

Specs:
Voltage Range: 0~100V DC
Accuracy: +/- 0.1V
Input Voltage: 4.0~6.5V
Working Current: 9mA
Lead length: 195mm
Size: 31 x 15 x 8.5mm
Weight: 6.25g (inc leads and sensor)

If you're looking for the ultimate steering servo for your 1/8th scale truggy, we have just the thing!

The TrackStar TS-621MG is a standard size digital servo featuring a metal geartrain, coreless motor and a fast 0.14sec transit time. Add to that it's excellent performance and tricked out looks, and you have one outstanding steering servo for the price!

Specs:
Weight: 57g
Size: 39.0mmx19.5mmx38.5mm
Torque: 16.8kg.cm (4.8V)~21.2kg.cm (6.0V)
Speed: 0.16sec/60deg (4.8V)~0.14sec/60deg (6.0V)
Voltage: 4.8~6.0V
Type: Digital Standard
Motor: Coreless Motor
Gear Train: Alloy Gears
Ball Bearing: Dual Japan NSK Ball Bearing
Lead Length: 255mm
Plug: JR/Futaba
Spline Count: 25

The Turnigy TGY-iA6C is a new style in receivers. It builds on the reliability of the TGY-iA6B receiver but it is built specifically for using with PPM, i.BUS and S.BUS configurations. This is an excellent addition to your Turnigy TGY-i6s and TGY-i10 transmitters.

Dual antennas give the iA6C for unparalleled reception. Built-in connections allow you to use our optional telemetry sensors. 

An excellent receiver for multi-rotor drones as it cuts down on cabling and with built-in battery monitoring.

Features:
• Reliable, interference free 2.4GHz AFHDS 2A signal operation
• PPM, i.BUS, S.BUS
• Ultra-light weight design
• Dual antennas for most reliable interference free operation
• Connection ports for use with optional telemetry sensors
• Battery monitoring

Specs:
Channel: 8
Frequency: 2.4GHz ISM Frequency Range
Band width: 500KHz
Band quantity: 135
RF Power: <20dBM
System: AFHDS2A
Code type: GFSK
Output data: PPM, i.BUS, S.BUS
Antenna length: 26mm
Power: 4.0V~6.5V
Wireless Update: Yes
Channel data: Center position: 1500±30us; range: 1000~2000±30us
Channel delay: <15ms
Net Weight: 7.9g
Dimensions: 41x25x10mm
Range: >300 meters
Certification: CE0678, FCC ID: N4ZIA6C00, RCM

Easy to use, simply follow the links on the FrSKY website, connect the receiver to the STK and plug the STK into your computer via the USB port. The FrSKY STK updates all FrSKY receivers that support S.Port.

The Turnigy X6B is a 6-channel two-way receiver designed for multi-rotor aircraft. It uses the 2.4GHz AFHDS 2A (Automatic Frequency Hopping Digital System) protocol and has a dual omnidirectional antenna with superior noise reduction techniques for reliable interference-free operation. It’s compact, easy to install, and boasts a rich easy-to-use interface. The X6B supports 6-channel PWM output, standard PPM output, and i-BUS support for up to 18 channels alongside a reliable voltage sensor interface. This is an excellent addition to your Turnigy TGY-i6s, TGY-i10, and Evolution transmitters as well as a number of other AFHDS 2A transmitters such as FS-i10, FS-i8, FS-i6, FS-i6S, FS-i6X, FS-i4, and FS-i4X. An excellent receiver for multi-rotor drones as it is lightweight cuts down on cabling and comes with built-in battery monitoring.

Designed to be splash-proof, the HK-GT2 receiver is a great choice for boats, cars on muddy terrain and rainy days. Stop changing receivers from model to model and get an extra receiver now.

This is a very handy little device that is used to sequence the landing gear doors and landing gear both during extension and retraction.

With the use of spitter leads you are able to sequence an entire gear and door system on many models that require correct sequencing from just one of these units and from a single channel on your reciever.

There are two selectable sequence types and there is an instruction leaflet included.

Specs:
Dimensions: 52x18x5mm
Voltage range: 4.8-6.0v
Weight: 5.5g

*Color may vary

This is an all laser cut ply cockpit that has an integrated Pan and Tilt system and mounts for a complete FPV system. The Base frame has provisions for the FPV transmitter, wiring and battery. The Pan and tilt system has 2quick release mounting positions, the forward position giving an unobstructed clear view, well the back mounting position allows you to reuse the Lexan canopy for a sleek aerodynamic FPV rig. The Pan and Tilt hold a 180deg servo for pan and a 90 deg for tilt (not included). There are various mounting and access holes to accommodate a wide range of FPV cameras from board to cube style.

The Base frame has provisions for the FPV transmitter, wiring and battery. The Pan and tilt system has 2quick release mounting positions, the forward position giving an unobstructed clear view, well the back mounting position allows you to reuse the Lexan canopy for a sleek aerodynamic FPV rig. The Pan and Tilt hold a 180deg servo for pan and a 90 deg for tilt (not included). There are various mounting and access holes to accommodate a wide range of FPV cameras from board to cube style.

Features:
• Lasercut pre-built construction
• Can be adapted to other planes
• 2 mounting positions for the Quick release pan and tilt
• Mounting provisions for a full FPV system

Specs:
Weight: 78g
Size: 98x96x221mm WxHxL
Fitment: Direct fit for the Hawkeye 1700 PC FPV plane (can be adapted to others)

Required:
2 x 9g servos, recommend 180deg and Metal Gear.

Alu Undercarriage (1pair/bag)

Size:255mm 
Weight: 108g / pair

The HobbyKing helicopter pitch gauge is made from ultra-rigid fiberglass board and features dual ball bearings to ensure accurate measurements every time. This pitch gauge is supplied in kit form to keep production costs down which means we can pass the savings on to you!

Specs:
Measurement: +/- 20 Deg
Size: 145mm x 105mm
Max Blade Width: 80mm

Note: An assembly guide can be found in the FILES tab below.