Bargain Bin

HobbyKing® Bixler 3 Trainer 1550mm - Replacement Wheel Pant Set

HobbyKing® Bix3 Trainer 1550mm - Replacement Control Rod Set

HobbyKing® Bix3 Trainer 1550mm - Replacement Prop Adapter

Excellent Quality Nylon Spinner with Lightened Alloy Backplate 70mm Yellow - Mount hole 8mm

Desert Fox Printed Body Panels Full Set (1 set)

Desert Fox Clear Body Full Set

Desert Fox Dirt Proof Cover (Clear) (1 set)

BT-4 Rear Suspension Arm Mount R2.0 TU1007

BT-4 Straight shaft (Spool) TU1042-2

Progressive Shock system for BT-4 gives a progressive dampening effect through the shock travel so the effect is softest at the start and harder at the end. Includes blank shock pistons so you can drill your own holes for precise tuning to your individual needs.

Specs:
Length: 14mm
Diameter: 11mm
Piston: 10mm x 2mm

A kit of plywood parts for the Durafly Tundra V1, V2, V3, and Night to build a mount/tray for your FPV equipment. The Tundra series is the perfect mount for FPV flying due to its stability and slow flying characteristics.

Basher RZ-4 1/10 Rally Racer - Composite Rear Upright (2pcs)

Clear Body - Basher PBull 1/18 4WD Desert Buggy

TrackStar Shock Bottom Cap Set with O-Ring S120052

Compatible with the following Shock Absorbers
S12400, S160023, S160026, S160085, S160100, S124300, S160323, S160326

TrackStar Hardened Shock Shaft (x4)

Specs:
Diameter: 3.2mm
Length:48mm

Compatible with the following Shock Absorbers
S160100

TrackStar Suspension Spring (x4)

Specs:
Wire Thickness: 1.1mm
Internal Diameter: 14mm
Length: 55mm
Spring Rate:  1.2Kg
Color: Gold

Compatible with the following Shock Absorbers
S160023, S160026, S160323, S160326

Pulse / Heart Rate Sensor Module for Arduino

Specs:
Dimensions: 15 x 2mm
Weight: 2.66g

On screen display (OSD) module for Shark X6/X8 flight controllers.

Specs:
Input voltage: 5V DC
Operating Temperature: -10°C ~ 50°C
Cable length: 130mm
Dimensions: 33 x 20 x 11mm
Weight: 10.5g 

Included:
OSD module

One of a series of four DIY robot car kits, these are great value and great fun for kids of all ages to put together.

You will only need some basic tools, some solder and a soldering iron and within a few hours you will have an operating robot car.

This model is activated by light sensor and will respond to a flashlight or other direct light source.

Includes:
1 x Light controlled robot car kit 

Note: This robot does not require programming.

One of a series of four DIY robot car kits, these are great value and great fun for kids of all ages to put together.

You will only need some basic tools, some solder and a soldering iron and within a few hours you will have an operating robot car.

This model is an obstacle avoider, with a sensor that detects objects to its front. 

Includes:
1 x Obstacle avoiding robot car kit 

Note: This robot does not require programming.

Make use of that free wind power electricity!

For use with the EK5100 Wind Turbine kit is this versatile charging unit.

Simply connect it up to your wind turbine and it can be used to charge your mobile phone, your ipod or your rechargable batteries. 

Includes:
Ek5400 Charger
Leads and cables

Make light and music with that free wind power electricity!

For use with the EK5100 Wind Turbine kit is this melody and light board.

Simply connect it up to your wind turbine and it can be used to power the sound and light board in various modes.

Includes:
Ek5300 Board
Instructions

Spare Part - Premium BNC 1.3m RG223 cable for Scherrer Rx700LR Long Range UHF system

Soldering Iron Tip Set (10 pcs)

Suits Hakko type soldering irons that have an attachment spigot diameter of 4mm. Containing fine tips to bevel edges, this pack has you covered for the majority of hobby projects from PCB soldering to battery connectors. 

Reliably monitor the voltage of your battery with the Turnigy TGY-CVT01 Voltage Sensor.

As a great alternative to setting a timer, fly or drive your model based on the actual voltage of your battery. This way if your voltage drops quicker than usual due to harder running, you can avoid over discharge your pack. Or, perhaps you're having a nice relaxed day? Enjoy longer run times and don't cut yourself short.

This small, compact sensor is also a perfect way to add piece of mind when running a high performance model by allowing you to check that the battery voltage isn't dropping excessively under load.

For use with the TGY- i10 and i6 transmitters and TGY-iA10 and i6 V2 receivers.

Designed to daisy chain together with other TGY-C series sensors.

Features:
• High quality, compact sensor
• Futaba style input and output connectors
• Great for monitoring battery voltage, no need to set timers anymore
• Works with TGY- i10 and i6 transmitters and TGY-iA10 and i6 V2 receivers

Specs:
Voltage Range: 0~100V DC
Accuracy: +/- 0.1V
Input Voltage: 4.0~6.5V
Working Current: 9mA
Lead length: 195mm
Size: 31 x 15 x 8.5mm
Weight: 6.25g (inc leads and sensor)

Turnigy 9XR FPV Monitor Mounting Arm.

A mounting arm specially designed to hold Telemetry units or FPV Monitors on
top of your 9XR.
Compatible with most standard FPV monitors and our Quanum Telemetry system.

*Requires the 9XR Transmitter Stand (see related items)

3x30P Pin Socket - 2.54mm Pitch (5pcs/bag)

Perfect for DIY electronics projects.

When it comes to hardware, quality does matter! These titanium machine screws not only offer improved strength over steel, they are also much lighter in weight. These are ideal for use in performance models where shaving weight is absolutely critical, or for any project requiring high strength, lightweight hardware.

Spec.:
Size: M2.5 x 8mm
Weight: 0.18g(Each)

When it comes to hardware, quality does matter! These titanium machine screws not only offer improved strength over steel, they are also much lighter in weight. These are ideal for use in performance models where shaving weight is absolutely critical, or for any project requiring high strength, lightweight hardware.

Spec.:
Size: M2.5 x 8mm
Weight: 0.20g(Each)

This high quality switch is made in Taiwan and is proven to exceed more than 10000 switch cycles during testing.
This switch is designed for life time use.

Great for repairing your radio or making a swtich for your own project.

Spec.:
Style: 2-Way, Round Head
Dimension(LxWxD): 13x8x7mm(Plastic part only)
Length: 29mm(Switch & Mounting hole)
Mounting Hole Size: M6x8mm
Weight: 3.7g(Each)

30P Pin Header and Socket - 2.54mm Pitch (5 pcs)

Perfect for DIY electronic projects.