Bargain Bin

This is an all-in-one balance board adapter that allows you to balance charge 2~6S lipoly batteries with Thunder Power/Flight Power, Hyperion, JST-XH and JST-EH balance plugs. This makes it simple and eliminates the need for carrying separate balance adapters for each type of battery.

Specs;
Cell Count: 2~6S (7.4~22.2V)
Balance Connector Type: TP/HP/XH/EH

*Note: Can only be used to balance one type (TP/HP/XH/EH) at a time. Do not connect more than one type of balance leads to adapter board at same time or damage may occur.

120mm JST-SH1.0 Servo extension (5pcs/bag)

Spec.
Weight: 0.7g(Each)

8mm Gold Connectors and housing set.

Rated to around 170A
Excellent for high voltage/ high current systems.

Includes:
2 male connectors, 2 femal connectors and 2 housings

Weight: 23g

4mm Gold Plated Banana Plug (10pc)

This adapter will convert a 5.5mm Bullet Connector equipped battery to a T-Connector for use with a T-Connector equipped ESC or Charge lead.

Spec:
Weight: 9g(Each)

Mini black T Connector pack (5 Pairs)

Specs:
Base Dimensions: 5mm x 8mm
Contact Dimension: 3mm x 5mm x 1mm
Rating: 10amps continuous

Super flexible 26AWG twisted silicone male to male servo lead. These are specifically made as signal leads for RX to Flight controller connections, the light 26AWG silicone wire is so flexible it transfers virtually no vibration to the Flight controller, well the twist helps reduce inducted noise. If used in conjunction of having only one lead vertical and the other leads turned on their side for signal only, makes for a clean and minimal vibration transfer installation. Or better yet a single CPPM/SBUS single lead. 

Specs:
Length: 130mm(black/red/white)
Connection: Male JR style plug on each end.

Super flexible 26AWG twisted silicone male to male servo lead. These are specifically made as signal leads for RX to Flight controller connections, the light 26AWG silicone wire is so flexible it transfers virtually no vibration to the Flight controller, well the twist helps reduce inducted noise. If used in conjunction of having only one lead vertical and the leads turned on their side for signal only makes for a clean and minimal vibration transfer installation, or better yet a single CPPM/SBUS single lead.

Specs:
Length: 80mm(black/red/white)
Connection: Male JR style plug on each end.

Mini Tamiya to T-Connector Battery Adapter (2pcs/bag)

This adapter will convert a Mini Tamiya equipped battery to a T-Connector for use with a T-Connector equipped ESC or a T-Connector Charge lead.

A handy adapter to convert an XT60 equipped battery to an MPX style connector. Useful for use with MPX equipped ESC or Charge leads.

Spec:
Weight: 5.3g(Each)

HXT 4mm bullet to XT90 Battery Adapter (2pcs)

This adapter will convert a 4mm bullet equipped battery to a XT90 for use with a XT90 equipped ESC or a XT90 Charge lead.

XT90 to 4.0mm bullet Battery Adapter (2pcs/bag)

This adapter will convert a XT90 equipped battery to a 4.0mm bullet for use with a 4.0mm bullet equipped ESC or a 4.0mm bullet Charge lead.

Specs:
Model: TGY-225MG
Voltage: 4.5 - 6v
Speed: .12s
Running Current: 180mA
Torque: 3.5kg/cm
Gears: Metal
Weight: 26g
Spline Count : 21 Tooth

Narrow dead band width.

This is a great way to avoid power shorts.

Gold connectors on their own are notorious for creating a short circuit and looking messy. Use these to keep your connections safe and looking neat!

Rated to 20Amp these connectors are an excellent replacement for JST plugs on todays small yet high C rated batteries.

Basher RZ-4 1/10 Rally Racer - Composite Rear Upright (2pcs)

The MultiStar White edition multirotor propeller started as an optimized blade design for the target motor/RPM combinations in Multirotor use. After comparing a host of construction options, a wood core was selected for its super stiff property’s, light weight and vibration resistant properties.

The MultiStar White Edition Propellers come packaged in a set of two CW/CCW and matching mounting hardware and thrust washers. The high visibility White color adds safety and style to your multi-rotor setup.

Specs:
Size: 9.4X4.3
Mounting Style: Hub Style with CW/CCW shaft nuts included 

Included:
One CCW and one CW propeller
Mounting Hardware and thrust washer (DJI Style shaft nuts)

Clear Body - Basher PBull 1/18 4WD Desert Buggy

TrackStar Shock Bottom Cap Set with O-Ring S120052

Compatible with the following Shock Absorbers
S12400, S160023, S160026, S160085, S160100, S124300, S160323, S160326

TrackStar Hardened Shock Shaft (x4)

Specs:
Diameter: 3.2mm
Length:48mm

Compatible with the following Shock Absorbers
S160100

TrackStar Suspension Spring (x4)

Specs:
Wire Thickness: 1.1mm
Internal Diameter: 14mm
Length: 55mm
Spring Rate:  1.2Kg
Color: Gold

Compatible with the following Shock Absorbers
S160023, S160026, S160323, S160326

These propellers are beautifully finished and highly efficient

APC Style Propeller 15x5.5 Red (CW/CCW) (2pcs)

These propellers are beautifully finished and highly efficient

T-Style Propeller 15x5.5 Yellow (CW/CCW) (2pcs)

Pulse / Heart Rate Sensor Module for Arduino

Specs:
Dimensions: 15 x 2mm
Weight: 2.66g

On screen display (OSD) module for Shark X6/X8 flight controllers.

Specs:
Input voltage: 5V DC
Operating Temperature: -10°C ~ 50°C
Cable length: 130mm
Dimensions: 33 x 20 x 11mm
Weight: 10.5g 

Included:
OSD module

One of a series of four DIY robot car kits, these are great value and great fun for kids of all ages to put together.

You will only need some basic tools, some solder and a soldering iron and within a few hours you will have an operating robot car.

This model is activated by light sensor and will respond to a flashlight or other direct light source.

Includes:
1 x Light controlled robot car kit 

Note: This robot does not require programming.

One of a series of four DIY robot car kits, these are great value and great fun for kids of all ages to put together.

You will only need some basic tools, some solder and a soldering iron and within a few hours you will have an operating robot car.

This model is an obstacle avoider, with a sensor that detects objects to its front. 

Includes:
1 x Obstacle avoiding robot car kit 

Note: This robot does not require programming.

Make use of that free wind power electricity!

For use with the EK5100 Wind Turbine kit is this versatile charging unit.

Simply connect it up to your wind turbine and it can be used to charge your mobile phone, your ipod or your rechargable batteries. 

Includes:
Ek5400 Charger
Leads and cables

Make light and music with that free wind power electricity!

For use with the EK5100 Wind Turbine kit is this melody and light board.

Simply connect it up to your wind turbine and it can be used to power the sound and light board in various modes.

Includes:
Ek5300 Board
Instructions

Spare Part - Premium BNC 1.3m RG223 cable for Scherrer Rx700LR Long Range UHF system

Soldering Iron Tip Set (10 pcs)

Suits Hakko type soldering irons that have an attachment spigot diameter of 4mm. Containing fine tips to bevel edges, this pack has you covered for the majority of hobby projects from PCB soldering to battery connectors. 

Reliably monitor the voltage of your battery with the Turnigy TGY-CVT01 Voltage Sensor.

As a great alternative to setting a timer, fly or drive your model based on the actual voltage of your battery. This way if your voltage drops quicker than usual due to harder running, you can avoid over discharge your pack. Or, perhaps you're having a nice relaxed day? Enjoy longer run times and don't cut yourself short.

This small, compact sensor is also a perfect way to add piece of mind when running a high performance model by allowing you to check that the battery voltage isn't dropping excessively under load.

For use with the TGY- i10 and i6 transmitters and TGY-iA10 and i6 V2 receivers.

Designed to daisy chain together with other TGY-C series sensors.

Features:
• High quality, compact sensor
• Futaba style input and output connectors
• Great for monitoring battery voltage, no need to set timers anymore
• Works with TGY- i10 and i6 transmitters and TGY-iA10 and i6 V2 receivers

Specs:
Voltage Range: 0~100V DC
Accuracy: +/- 0.1V
Input Voltage: 4.0~6.5V
Working Current: 9mA
Lead length: 195mm
Size: 31 x 15 x 8.5mm
Weight: 6.25g (inc leads and sensor)

Turnigy 9XR FPV Monitor Mounting Arm.

A mounting arm specially designed to hold Telemetry units or FPV Monitors on
top of your 9XR.
Compatible with most standard FPV monitors and our Quanum Telemetry system.

*Requires the 9XR Transmitter Stand (see related items)

3x30P Pin Socket - 2.54mm Pitch (5pcs/bag)

Perfect for DIY electronics projects.

When it comes to hardware, quality does matter! These titanium machine screws not only offer improved strength over steel, they are also much lighter in weight. These are ideal for use in performance models where shaving weight is absolutely critical, or for any project requiring high strength, lightweight hardware.

Spec.:
Size: M2.5 x 8mm
Weight: 0.18g(Each)

When it comes to hardware, quality does matter! These titanium machine screws not only offer improved strength over steel, they are also much lighter in weight. These are ideal for use in performance models where shaving weight is absolutely critical, or for any project requiring high strength, lightweight hardware.

Spec.:
Size: M2.5 x 8mm
Weight: 0.20g(Each)