Bargain Bin

The Orange OpenLRS 433MHz TX Module is designed for use with APM flight control software and can be programmed to use your choice of protocol and any channel in the 433MHz range. Fully user-customizable, the transmitter system can even be programmed to utilize additional features such as telemetry, operative remote control via stics (cPPM ready), and mission control.
It is equipped with Bluetooth technology so the user can connect it to a tablet, smartphone, or PC. All telemetry data, mission planning, and flight modes will be available in APM Mission Planner on PC or Droid Planner, or similar apps for Android devices. Thanks to the Bluetooth function, no additional leads are required to setup/program the transmitter module.

Upgrade your Quanum DIY FPV V2 Goggles with this V2 add on kit.  It incorporates many new features that you have all been asking for and will effectively bring your V2 Goggle set up to V2Pro specs at minimal cost. 

A new, clear acrylic three lens set (1X, 1.25X or 1.5X magnification) and lens frame adapter providing a superior improvement in quality over the previous fresnel lens set. 

A battery pouch with velcro flap and buckle has been added and is excellent for mounting your battery on to the goggle's headstrap (behind the user's head) and will take a battery up to 77mm x 35mm x 22mm.

An EVA foam adapter for mounting a smartphone onto your goggles will turn your V2's into a Virtual Reality headset for gaming etc. Recommended for smartphone sizes up to Samsung Galaxy S6. Smartphone ports are accessible on the ends and the V2's neoprene glove front straps will hold it in place.

Extra comfortable sponge rubber strips with double sided tape have been added for extra cushioning when wearing the goggles and are simply cut to size to match the users requirements. 

Features:
• New clear acrylic lens set and frame (1.0X, 1.25X and 1.50X magnification)
• Battery pouch
• Metal “S” loop for top strap adjustment to improve wearer comfort and fitting
• Extra comfortable sponge rubber cushoining strips for facial comfort
• EVA foam adapter for smartphone for mounting
• A set of extension/conversion cables including:
      a) 3.5mm female phone jack to 2.5mm male phone plug adapter
      b) FPV DC jack to 1x5521 DC plug, 2x3315 DC plug (Length = 350mm)
      c) 3.5mm phone female to RCA male cable (Length = 150mm)
      d) XT60 male to FPV DC jack (Length = 210mm)
      e) 3.5mm phone female to RCA female cable (lenght = 150mm)

Note: A set of modification instructions are located in the "Files" tab below showing the alternate mounting method for the goggle monitor allowing for an increase in focal plane length.

Also available for use with this product:

Quanum DIY FPV Goggle V2Pro Upgrade Glove (Urban Digital Cam)

Quanum DIY FPV Goggle V2Pro Upgrade Glove (Black/Red)

Quanum DIY FPV Goggle V2Pro Upgrade Glove (Fluro Pink)

The OrangeRx 6ch compact receiver has been designed for FPV racing drones with carbon frames. The extra-length antenna allows you to route them outside of the frame for extended range and a robust link to your transmitter.

OrangeRx receivers are built using original components, 32-bit MCUs, and with state of the art SMT automation to ensure a quality product each and every time. Every single receiver is manufactured using impedance-controlled PCBs with exact tuning to provide signal stability and range that exceeds any of the previous generation ORX products. In fact, our testing has shown that the R617XL exceeds the range of other receivers in the same class.

All R617XL OrangeRx receivers are QC tested using our latest method that ensures range checking takes place as the receiver is programmed. Simply put, if the R617XL cannot pass the range check it cannot be programmed, this ensures 100% of R617XLs are guaranteed to work flawlessly. The R617XL ushers in a new era of quality, reliability, and performance for the OrangeRx lineup.

The receiver features "True Diversity" technology, which is especially important for long-range flights and in situations where you need that more robust reception. This receiver is very useful where carbon is used in the construction of your model where the antenna can be in the shadow of the airframe. If one of the antennae cannot receive a signal due to its orientation then the satellite will use the other one to receive the commands from the transmitter.

Multistar 1704 V2 Prop Adapter Set 2 x CW / 2 x CCW.

High-quality prop adapter set to fit the Multistar 1704 range of motors. The package contains 2 x clockwise and 2 x counter-clockwise adapters and a complete set of the required fixing screws.

TrackStar V2 electric motor replacement sensor incorporating rear bearing for 3.5T~8.5T motors.  

These new prop hubs are ideal for achieving that finished look to your model and the new raised motor mount will assist in providing some additional clearance for the back of the shaft against the model's firewall.

This package will fit the SK3 Series of motors in the following sizes only: 2822, 2826, 2830, 2836.

Includes:
1 x Prop hub
1 x motor mount
4 x mounting screws

These new prop hubs are ideal for achieving that finished look to your model and the new raised motor mount will assist in providing some additional clearance for the back of the shaft against the model's firewall.

This package will fit the SK3 Series of motors in the following sizes only: 3530

Includes:
1 x Prop hub
1 x motor mount
4 x mounting screws

TrackStar SEG 21 Racing Engine replacement rear cover.

*Color may vary

Ball Joint Housing 3 - A3011

Turnigy FBL100 Main Rotor Head Block

Durafly® ™ Messerschmitt Bf.110 - Replacement Radiator Set (1pair)

Self Adhesive Wing Tape 45mic x 45 mm x 100m ( Wide - Red) - Perfect for adding strength and color to your foam model!

Self Adhesive Wing Tape 45mic x 45 mm x 100m ( Wide - Orange) - Perfect for adding strength and color to your foam model!

Self Adhesive Wing Tape 45mic x 45 mm x 100m (Wide - Black) - Perfect for adding strength and color to your foam model!

Self Adhesive Wing Tape 45mic x 24 mm x 100m (Narrow - Yellow) - Perfect for adding strength and color to your foam model!

HXT 4mm Connector to T-plug conversion charge lead

This will connect to a Lipo fitted with HXT 4mm connectors and a charge lead fitted with a T-plug

FX070C 2.4GHz 4CH Flybarless RC Helicopter Replacement Tail Boom Set.

The glove mount is the ideal mounting solution for your action camera and is perfect for skiing, snowboarding, mountain biking, paddle sports, the list is endless. The glove mount is ideal for any sport where you want to get a "lower than helmet" view of the action.

All in all it's a more immersive way to film than on a helmet, with this mount you will capture the full motion of your activity as you move your hand. Fully adjustable, the glove mount harness is one of the most popular mounts for action cameras, and is as versatile as you would like it to be!

The glove mount is compatible with the Turnigy Action Cam and all GoPro series cameras.

Features:
• Polycarbonate construction
• Fully adjustable to provide a perfect fit
• Securing hook and loop buckle to ensure your harness does not come loose
• Can be used for almost any application

Specs:
Material: Elastic / Polycarbonate construction
Weight: 60g

Protect your Xiaoyi action cam from dirt, splashes and minor knocks with this custom molded silicone case and lens cap set.
Can be used with similar sized cameras.

Specs:
Material: Silicone
Color: Red
Internal dimensions: 60.4 x 42 x 21.2mm

A strong, waterproof case for your Xiaoyi action camera with access to all camera funtions and an adjustable universal quick release mount.

Specs:
Weight: 74g

Screw Grub Hex M5x5mm (10pcs/pack)

This is the WWI sound pack chip for the V4 MrRCsound sound unit. It includes 6 common engine sounds used in a number of WWI era Allied and Axis planes. These are high quality digital recordings of the real things. Sounds: Fokker D VII, Real Gnome, Le Rhone, Easy Gnome, Tiger Moth, and Stearman Plus aux. sounds for each.

For use with MrRC Sound V4.1 Speakerless Sound System found here.

This is the WWII sound pack chip for the V4 MrRCsound sound unit. It includes 6 common engine sounds used in a number of WWII era Allied and Axis planes. These are high quality digital recordings of the real things. Sounds: Allison, BMW 801, Sakae (Zero), Mikulin AM-38 (IL-2/Mig-3), Bristol Centaurus (Hawker Sea fury), and Wright Cyclone. Plus aux. sounds for each.

For use with MrRC Sound V4.1 Speakerless Sound System found here.

Tamiya premium quality, clog free, wet and dry sanding paper. Ideal for modelers looking for the perfect finish. The pack contains 2 x P180, 1 x P240, 2 x P320. 

Specs:
Grades: P180, P240, P320
Dimensions: 229 x 93mm
Quantity: 5 pcs

Tamiya Standard Flat Brushes are made from horse hair and feature lightweight hardwood handles. Ideal for painting larger surface areas of models.

Specs:
Bristle Material: Horse hair
Bristle Length: 20mm
Handle Material: Hardwood
Weight: 4.41g
Dimensions: 220 x 7mm

Tamiya Standard Blunt Brushes are made from horse hair and feature lightweight hardwood handles. The brushes are ideal for fine detailed artwork.

Specs:
Bristle Material: Horse hair
Bristle Length: 7mm
Handle Material: Hardwood
Weight: 2.22g
Dimensions: 200 x 5mm

TF Model ESC and LED lighting power distribution board suitable for most quads and multi-rotors including SMACK TF250, OrcaTF280, TF650, TF680 and TF690.  A 3 position control channel can be setup to change the LED from Solid, Slow blinking and fast blinking LED lights.

Specs:
Dimensions: 50 x 50mm
Weight: 14g
ESC Output : 6
5V Output : 1
12V Output : 1
Mounting Holes : 45mm

Diff.Gear Housing (2pcs) - 118B, A2006, A2023T and A2035

Pins for Front Upright 2 pcs - 118B, A2006, A2023T and A2035

31mm Alloy Prop Nut/Spinner Suits 10mm Thread (Anodised Silver)

Height:30mm
Width:31mm
Thread Size:10mm
Thread Depth:25mm

31mm Alloy Prop Nut/Spinner Suites 8mm Thread (Anodised Black)

Height:30mm
Width:31mm
Thread Size:10mm
Thread Depth:25mm

Prop Nut/Spinner 22mm Alloy 10x1.0

Prop Nut/Spinner 22mm Alloy M10x1.25

Prop Nut/Spinner 22mm Alloy M10x1.00 Anodised Black