Introducing our EPP 3D MX2. Featuring a fantastic design and layout, this all out EPP 3D'er will satisfy the most eager 3D pilots!

Its fuselage is torsionally very stiff yet light with loads of space beneath the long top hatch for your radio and power system. The wing is a one-piece affair featuring EPP construction, a very accurate symmetrical airfoil with 2 additional spars to minimize flex and twist. The control surfaces are something else - the elevator, rudder, and ailerons feature a 3 layer construction (Epp-Depron-EPP) making for stiff surfaces and NO flex at extreme throws! Snap rolls "Snap" and the control response is instantaneous.

The light - yet rigid - airframe adds up to one great flying 3D "foamy". Waterfalls, harriers, flat spins, rolling circles this model has the precision to perform these and any other moves you can think of!

Assembly of the airframe in a quick 10-15 minute process with the help of a little medium CA. The radio and power system layouts are very straightforward, the long top hatch making for easy access.

This is a great model for general park flying and hardcore 3D. You will be hard-pressed to break this model, it will take hard knocks and just keep bouncing back every time!


Features:
• Tough EPP material, light-weight, and crash-resistant
• Stiff EPP/Depron composite control surfaces
• Revolutionary design adds to the structural integrity and the rigidity of the airframe
• Light-weight provides optimal wing loading
• Outstanding aerobatic performance and 3D maneuverability.
• Simple design allows for easy equipment access and installation
• The stand out color scheme great for orientation


Specs:
Wingspan: 955mm
Length: 945mm
Wing Area: 15.2dm2
Weight: 550g (without battery)



Requires:
4 channel radio system
2217 950-1100KV Brushless outrunner 
30Amp ESC 
3S 11.1V 1100-1300MAH Li-Po 
10x4.7/11x4.7 propeller 
4 x 9g servos

This little kit takes around 4hrs to build and will satisfy the throttle jocky in all of us!

The flycat comes with 56mm EDF and you will need a 25A ESC & 4800kv inrunner.

This plane is extremely fast, (over 100mph!), however still stable at slow flight.

Spec.
WingSpan: 640mm
Length: 800mm
Weight: 290g
BESC : 25A (not included)
Motor: 4800kv 20-30 size Inrunner (not included)
Lipoly: 1300mAh 11.1v 20C (not included)

Required.
Motor & ESC
3 x 9g Servo
5 or 10min Epoxy (Araldite)
1 x Servo Y lead
1 x Servo Extention lead
12AWG Silicon wire (20cm For motor to ESC)
1300mah 11.1v 20C lipo battery
Your own receiver and transmitter

Our flight report.

Kit fits together well, light sanding of leading and trailing edges required to remove extra foam. We chose to not strengthen the wing with CF tubing, which didnt prove to be an issue, even at full speed high G turns.

We opted to mount the BESC being the battery area, in case the battery needed to be moved forward to adjust CofG, however this wasnt necessary.

EDF was mounted on the stick mount. Stick mount was shortened, with the extra piece used to raise the EDF off the stick to clear the EDF shroud. 2 bolts held the fan unit to the stick, one before and one after the fan blades.

First flight.

We kept CofG 9.5cm from the apex of the wings leading edge. The flycat was hand launched at 3/4 throttle, accelerating quickly. To our surprise, no trimming was required.

The flycat is an extremely fast kit to fly, and required a lot of elevator in turns. We suggest putting the elevator on maximum throws. It needs HUGE amounts of elevator during turns!

Overall an excellent plane which flys smoothly, even on windy days.

We suggest a good lipo pack, as this little hotty will chew through a 1500mAh in only 5 minutes. We used the ZIPPY-R 1800mAh 22C 3S1P pack for around 8 minute flights. As compared to the ZIPPY-Q pack which brought us short at about 7 minutes.

The H-King Crusader 30E is based on the classic stick design. This electric RC plane can be flown by both beginners and experts. It is constructed from lightweight ply and balsa that is painted with a high contrast color scheme. The Crusader will stand out on the ground and in the air at your local hobby club.

The Phoenix V2 2000 is a quick and easy to assemble electric powered glider with flaps and large ailerons for a precise, aerobatic performance. The EPO wings are fitted with a carbon spar for strength and 2 metal spars join the wings to the fuselage. Also, each aileron is reinforced with carbon to eliminate any chance of distortion or twisting. The wings are attached to the fuselage using fast connect clips, after flying, simply squeeze the clips to release the wings.

The Wargo Signature Edge 540T 3D is yet another incredible airplane in the series inspired by the renowned 3D pilot Michael Wargo. The Edge 540T was specifically designed for very precise 3D flying and aerobatic training. Michael Wargo, our team pilot, and 3D expert, wanted a foam aircraft that was stiffer, and lighter than other foamies. This was achieved by the combination of a stiff, lightweight balsa frame covered with lightweight, crash-resistant EPP foam.

The Dancing Wings Hobby Stick-14T 3D aerobatic trainer is the perfect choice for intermediate and experienced RC pilots alike. It is based on the classic stick design and is quite capable of all the usual aerobatic maneuvers, plus with the right power train, it doubles up as the perfect 3D trainer. It has a very wide speed range, it is just as happy flying slowly as it is screaming about the sky. For added fun and enjoyment, the strip ailerons are split halfway making for outboard ailerons and inboard flaps. This allows for really slow or steep approach landings, and if the flaps are mixed in with your other controls it allows you to customize the handling to suit your own flying style. 

The Dancing Wings Hobby Shining is a large lightweight profile-style foam kit that is quick and simple to build. It has been designed to be the perfect introduction to 3D flying and will perform extreme 3D maneuvers such as waterfalls, harriers, knife-edge loops, rolling circles, and much more.

The model is very straightforward to assemble, it is manufactured in pre-painted high-quality EPP foam sheet for the majority of the construction so the parts count is quite low, and carbon strips are supplied for strengthening. It builds up quickly into a good-looking, fun-to-fly lightweight extreme sport 3D plane that is perfect for park flying and on playing fields. This ARF model is supplied with a powerful 2216-950KV brushless motor, 30A brushless ESC, 10" propeller, and 4 x 9g servos.