Drones

A JST male plug to 2.54mm pitch male jumper lead for a variety of uses.

This lead is the best solution for batteries that are slightly out of balance; simply plug it into the individual cells on the balance lead, select a 1S charge rate and you can charge them one at a time to ensure they are all at optimum charge. 

Only use this method to restore cells that are slightly out of balance and remember that there could be something wrong with one of the cells so keep a close eye on it while charging.

Overall length: 70mm

The Vortex FPV Racer from ImmersionRC is an incredible piece of kit for the serious competitor, but like all things flying the ocassional mishap is inevitable!

This crash kit is a convenient way to keep a stock of all of those plastic parts most likely to be damaged in a serious "departure from controlled flight"

Included are all parts which mount the motors to the carbon fiber arms, the plastic pivot points, foldable arm clips, and all other plastic parts.

No carbon fiber parts are included (see Crash Kit 2.)

Included:
1 x Front bumper (FR4)
2 x Side plates
8 x Arm clips
4 x Arm pivot tops
4 x Arm pivot bottoms
4 x Landing bumpers
4 x Landing mounts
4 x Motor mounts
8 x Hex bushes
1 x Camera support base
1 x Camera support arm
4 x Damper pins
4x Damper circlip
4x Screw HA2x8
4x Screw HA2x6

Turnigy Talon Carbon Fiber Main Frame Upper Plate (1pc/bag)

Turnigy Talon Carbon Fiber Main Frame Lower Plate (1pc/bag)

HobbyKing X525 V3 Hardware Set (complete)

Anyone that flies the small 250 class quads has gone through a few props, whether you're trying to fit through something or had an acro mishap.  These prop guards will adapt to most 250 class frames via the motor mounting bolts. The guards will not only help save your props but help protect others and property from the high speed 5 inch props. 

Features:
• Adaptable to most frames
• Light weight and durable G10
• Protects your props and property 

Specs:
Size: For 5 inch props
Weight: 4.5g each
Mounting: Via motor mounting 12,16,19mm

Looking for the ultimate power system for your next Multi-rotor project? Look no further!

 The Turnigy Multistar outrunners are designed with one thing in mind - maximising Multi-rotor performance! They feature high-end 45SH magnets, high quality NMB bearings, 16 Poles, custom motor mount and all are precision balanced for smooth running, these motors are engineered specifically for multi-rotor use.

 The 4225-390 includes a prop adapter(6mm) and has a built in aluminium mount for quick and easy installation on your multi-rotor frame. These motors are supplied inside a nice foam lined Multistar metal box.

These Multistar outrunners have been specifically designed from the ground up for multi-rotor use and are not based on aeroplane motors.


Spec:
KV(RPM/V): 390
Lipo cells: 6s
Max Surge Watts(W): 330
Working current: 11 amps
Max.current(10s): 15 amps
No Load Current: 0.2 amps
Intemal Resistance: 0.24 ohm
Number of Poles: 16
Dimensions(Dia.xL): 42 x 24.5 mm
Shaft: 3 mm
Prop: 12 x 3 - 12 x 6
Weight: 86g

Looking for the ultimate power system for your next Multi-rotor project? Look no further!

The Turnigy Multistar outrunners are designed with one thing in mind - maximising Multi-rotor performance! They feature high-end 45SH magnets, high quality NMB bearings, 16 Poles, custom motor mount and all are precision balanced for smooth running, these motors are engineered specifically for multi-rotor use.

The 4225-610 includes a prop adapter(6mm) and has a built in aluminium mount for quick and easy installation on your multi-rotor frame. These motors are supplied inside a nice foam lined Multistar metal box.

These Multistar outrunners have been specifically designed from the ground up for multi-rotor use and are not based on aeroplane motors.


Spec:
KV(RPM/V): 610
Lipo cells: 4s
Max Surge Watts(W): 330
Working current: 16 amps
Max.current(10s): 22 amps
No Load Current: 0.3 amps
Intemal Resistance: 0.091 ohm
Number of Poles: 16
Dimensions(Dia.xL): 42 x 24.5 mm
Shaft: 3 mm
Prop: 12 x 3 - 12 x 6
Weight: 86g

This small lightweight 4ch switch is extremely handy for auxillary functions on all sorts of models. Plug the single lead into an auxillary switched function then switch your radio on, channel 1 on the electronic switch will then be active, cycle the auxillary switch once and channel 1 goes out and channel 2 comes on, cycle the switch once more and 2 goes out and channel 3 comes and so on until it comes back to channel 1. When the radio is switched off and then switched back on the unit will default to channel 1 each time. This unit is great for switching lights on and off and other low current applications.

Please note: For this switch to work correctly you will need to set the related channel travel to +- 100%.

Specs:
Input Voltage: 4.8~7.4v
Output Voltage: 4.8~7.4v
Maximum Current: 2amps
Length: 40mm
Width: 20mm
Height: 12mm
Weight: 7g
Input Cable: 21cm (JR type plug)

Quanum Exoskeleton for RunCam

Are you worried about your RunCam action camera not surviving a hard landing?  Simply give your RunCam a rigid exoskeleton frame.

Manufactured from super light weight alloy and machined to allow easy access to all of the RunCams many functions while maintaining a clear view from the lens, this frame gives you peace of mind when you send your favorite action camera into the thick of it!

Features:
• Purpose made to fit the RunCam Action Camera
• Tough, exoskeleton style design
• Superlight Alloy
• Access to all camera functions
• Bolt together case
• Lens shield

Specs:
Dimensions: 69 x 46 x 23mm
Weight: 21.5g

Are you looking to convert your SK450 quadcopter into a flying dead cat? If so, we have just the thing! This kit allows you to convert your standard SK450 into the "Dead Cat" style configuration with or without (your choice) the mess and hassle of mounting your own dead feline to the frame.

In addition to flying your deceased family pet around at home or your favorite local flying site, this configuration is also ideal for aerial video/photography as the front arms offer an extra wide field of view. The integrated camera mount plate located at the front of the frame is perfect for mounting a GoPRO or similar sized camera.

This kit includes everything necessary to convert your SK450 quad frame into either a wicked camera rig or a morbid dead pet mobile, the choice is yours!

*Note: This is a conversion kit only, the arms and other components are not included, it requires the use of original SK450 frame parts to complete.

Specs:
Front arm width: 490mm
Rear arm width: 375mm
Weight: 460g (completed frame w/out electronics)

Includes:
Lower main frame plate
Upper main frame plate
All necessary hardware

5.6mm x 18mm M3 Nylon Tapped Spacer (10pc).

Perfect for mounting Multi-rotor control boards.

Need to repair crash damage to a Multi-rotor flight board or add pin outs to any other electronics project?

These header pin blocks use the industry standard spacing of 2.54mm and are designed for soldering directly into printed circuit boards (PCB's). They are supplied in 30 pin lengths which can be easily cut to seperate individual pins.

There are 5 strips per pack.

Need to repair crash damage to a Multi-rotor flight board or add pin outs to any other electronics project?

These header pin blocks use the industry standard spacing of 2.54mm and are designed for soldering directly into printed circuit boards (PCB's). They are supplied in 30 pin lengths which can be easily cut to seperate individual pins.

There are 5 strips per pack.

Need to repair crash damage to a Multi-rotor flight board or add pin outs to any other electronics project?

These header pin blocks use the industry standard spacing of 2.54mm and are designed for soldering directly into printed circuit boards (PCB's). They are supplied in 30 pin lengths which can be easily cut to seperate individual pins.

There are 5 strips per pack.

Need to repair crash damage to a Multi-rotor flight board or add pin outs to any other electronics project?

This Header pin type is perfect for repairing Servo pins on most 4 (or more) channel receivers.

These header pin blocks use the industry standard spacing of 2.54mm and are designed for soldering directly into printed circuit boards (PCB's). They are supplied in 30 pin lengths which can be easily cut to seperate individual or groups of pins.

There are 5 strips per pack.

Why settle for only being able to charge your DJI Phantom 2 batteries at home?

The Quanum DC Field Charger charger allows you to quickly and easily charge your Phantom 2 batteries at the field from just about any 10~26VDC power source! This means easy battery charging from your car or truck's starter battery!

Simply connect the alligator clips to your vehicle's starter battery and the output lead to the Phantom 2 battery. The output lead features a polarity-protected plug which prevents improper connection. This charger provides up to 4A of current, matching that of the original DJI Phantom 2 battery charger.

30P Pin Header and Socket - 2.54mm Pitch (5 pcs)

Perfect for DIY electronic projects.

This compact, lightweight power supply filter helps clean up dirty DC current that often causes lines in wireless video images. The filter is an LC type that uses large value inductor and capacitor components. Their values are robust enough to remove moderate amounts of power supply noise.

The filter reduces DC-DC switcher supply ripple and helps clean noisy power from a shared battery. For example, if your robot or R/C model's 12V motor battery also powers the video camera and A/V transmitter, then this LC filter can help reduce the video "noise" that may appear when the motor is running.

Note: Installations with severe power supply noise may not be fully cured with this filter. In such cases a shared battery should be avoided.

Features:
• L-C Filter circuit reduces DC supply noise
• Built-in Reverse Polarity protection
• Supports up to 14 VDC at 1.7 Amp (maximum)
• Compact design

Specs:
Voltage drop over filter: 225mV at 900mA
Impedence/ESR: 0.06Ohm at 100kHz/16V
Ripple Current: 1190mA
DC Resistance: 0.25 Ohm/path
Dimensions: 38x12.5x11.5mm
Weight: 6.4g

HobbyKing™ Micro BEC 5V/1A

This great new switching mode BEC is the smallest yet made by HobbyKing. Our engineers developed this with micro and race quads in mind. It is extremely small and light weight but gives you excellent power for the Fight Controller, RX, etc.

Specs:
Input: 2-4cells Lipoly
Output (Constant): 5v/1A
Type: Switching
Input protection: Reverse polarity protection
Size: 10x9x7mm
Weight: 1.4g (wires included)

The OrangeRx 6ch compact receiver has been designed for FPV racing drones with carbon frames. The extra-length antenna allows you to route them outside of the frame for extended range and a robust link to your transmitter.

OrangeRx receivers are built using original components, 32-bit MCUs, and with state of the art SMT automation to ensure a quality product each and every time. Every single receiver is manufactured using impedance-controlled PCBs with exact tuning to provide signal stability and range that exceeds any of the previous generation ORX products. In fact, our testing has shown that the R617XL exceeds the range of other receivers in the same class.

All R617XL OrangeRx receivers are QC tested using our latest method that ensures range checking takes place as the receiver is programmed. Simply put, if the R617XL cannot pass the range check it cannot be programmed, this ensures 100% of R617XLs are guaranteed to work flawlessly. The R617XL ushers in a new era of quality, reliability, and performance for the OrangeRx lineup.

The receiver features "True Diversity" technology, which is especially important for long-range flights and in situations where you need that more robust reception. This receiver is very useful where carbon is used in the construction of your model where the antenna can be in the shadow of the airframe. If one of the antennae cannot receive a signal due to its orientation then the satellite will use the other one to receive the commands from the transmitter.

Multistar 1704 V2 Prop Adapter Set 2 x CW / 2 x CCW.

High-quality prop adapter set to fit the Multistar 1704 range of motors. The package contains 2 x clockwise and 2 x counter-clockwise adapters and a complete set of the required fixing screws.

Nylon Spacer 20mm M3 F/F Red (10pcs)

Specs:
Shape: Hex
Length: 20mm
Screw Thread: M3 Female/Female
Qty: 10 

Nylon Spacer 10mm M3 M/F Orange (10pcs)

Specs:
Shape: Hex
Length: 10mm
Screw Thread: M3 Male/Female
Qty: 10 

The Boom Stopper will help stop short circuits from blowing your electronics up. Simply plug in the Boom Stopper between the power source, usually your battery, and the components you are wanting to power for the first time. If there is a problem the inline 2A fuse will blow, instead of your components. When the fuse is blown the LED will light up indicating there is a short circuit and the Boom Stopper will reduce the current to a level that won't immediately damage your electronics, giving you time to remove the power supply. 

Lightweight Aluminium Round Section Spacer M3x38mm (Silver) (10pcs)

Lightweight aluminium spacers featuring a round cross section and a hex section (at each end) to fit a 5mm spanner. Ideal for use with helicopter and drone frames or similar applications where strong, accurate construction is required.

Specs:
Thread: M3
Length: 38mm
Weight: 1.5g each

The MultiStar Work Mat is a must have for any R/C hobbyist's work bench! Made from soft, grippy rubber and featuring ribbed compartments, it is perfect for containing small parts such as screws, nuts, washers and more. The backing is very grippy which will keep it from slipping on just about any surface. 

These smaller mats make excellent launch pads if you are taking off from uneven surfaces like grass or gravel.

The material is very soft and flexible allowing it to be easily rolled up for transport or storage. This makes it very easy to take with you to the race or field for on-site repairs. Never lose a screw again with the MultiStar Work Mat!

Features:
• Soft, grippy surface
• Ribbed compartments for containing small parts
• Flexible, can be rolled up for transport/storage

Specs:
Dimensions: 395 x 250mm

This latest addition to the XT60 range provides an integrated mount on the side of the XT60 with a 5mm mounting hole. This can be used to fix it to a drone frame (via a cable tie) or can be mounted to a frame stand-off. It could also be mounted to a battery tray in a plane or boat.

PROPDRIVE v2 motors are designed to perform right out of the box with tight windings, smooth bearings, correctly rated magnets, precision cut stator, and balanced rotors.

We design and build the PROPDRIVE v2 motors in-house, allowing us to control every aspect of production. We control the entire production line from material sourcing to machining, balancing, and final assembly. PROPDRIVE motors can be trusted to provide years of reliable service at a price every modeler can afford.

We have included a collet-style adapter, as well as a bolt-on prop adapter.

PROPDRIVE v2 motors are designed to perform right out of the box with tight windings, smooth bearings, correctly rated magnets, precision cut stator, and balanced rotors.

We design and build the PROPDRIVE v2 motors in-house, allowing us to control every aspect of production. We control the entire production line from material sourcing to machining, balancing, and final assembly. PROPDRIVE motors can be trusted to provide years of reliable service at a price every modeler can afford.

Performance Data (3S):
8x6: 309W, 29A, 1425g static thrust
9x4.7: 361W, 34A, 1506g static thrust
8x8: 376W, 36A, 1773g static thrust

Performance Data (4S):
7x5: 393W, 28A, 1511g static thrust
7x6: 449W, 32A, 1754g static thrust
8x4.1: 500W, 36A, 1733g static thrust

PROPDRIVE v2 motors are designed to perform right out of the box with tight windings, smooth bearings, correctly rated magnets, precision cut stator, and balanced rotors.

We design and build the PROPDRIVE v2 motors in-house, allowing us to control every aspect of production. We control the entire production line from material sourcing to machining, balancing, and final assembly. PROPDRIVE motors can be trusted to provide years of reliable service at a price every modeler can afford.

We have included a collet-style adapter, as well as a bolt-on prop adapter.

The H11WH is designed with beginners in mind and features a 6 axis gyro and a headless mode function, making this little quadcopter unbelievably stable and great for developing your flying skills. With stability and control are taken care of, you can concentrate on exploring and recording the footage at your favorite sites. 

It not only looks cool, but it is also equipped with a 2.4GHz WiFi operated 720p HD camera that can take stills or video at the press of a button, either on the transmitter or on your own mobile device! Using Wifi the H11WH turns your mobile device into an FPV monitor allowing you to see the live camera feed directly "from the pilot seat". 

PROPDRIVE v2 motors are designed to perform right out of the box with tight windings, smooth bearings, correctly rated magnets, precision cut stator, and balanced rotors.

We design and build the PROPDRIVE v2 motors in-house, allowing us to control every aspect of production. We control the entire production line from material sourcing to machining, balancing, and final assembly. PROPDRIVE motors can be trusted to provide years of reliable service at a price every modeler can afford.

We have included a collet-style adapter, as well as a bolt-on prop adapter.

Performance Data (3S):
4.75x4.75: 322W, 31A, 1124g static thrust
5x7.5: 492W, 49A, 1770g static thrust
6x4: 522W, 53A, 1583g static thrust

Performance Data (4S):
4.5x4.1: 520W, 38A, 1447g static thrust
4.75x4.75: 657W, 49A, 1819g static thrust
5x4.1: 681W, 51A, 1804g static thrust

The FQ777-126 is the ultimate FPV hexacopter drone. This hexacopter drone is small and light enough to fit literally anywhere! In fact, it is so small it even fits and charges within a special compartment within the Transmitter making it small enough to fit into your pocket.

Not only does the Tx double up as a handy storage compartment, but it also charges the LiPo battery whilst on the move. The Spider mini hexacopter FQ777-126 drone is fitted with a 6 axis gyro making it stable and easy to fly indoors or outdoors when recording on your mini HD camera.