Drones

GemFan Bull Nose 3545 GRP/Nylon Propellers CW/CCW Set Orange (2 pairs)

GemFan Propellers have set the gold standard in the small class Multirotor community, known for their durability, great balancing and superb hub centering and expendable price.

They come packaged as a set of 4, with two CW rotation and two CCW rotation.

There is a wide range of color options that can be mixed and matched to help with multirotor orientation. This is the perfect upgrade for any small multirotor.

Specs:
Size: 3545 (3.5"x4.5")
Color: Orange
Hub: 5mm
Material: Glass reinforced Nylon

Included:
2 x CW rotation
2 x CCW rotation
Adapters

These new upswept upgrade arms provide improved stability and faster forward flight. The arms are manufactured from toughened plastic which provides added strength.  

The arms are designed to fit DJI Flamewheel style multirotor frames such as the V500 / H550 Frames

Specs:
Length: 210mm
Weight: 62g (per arm)
Color: White

These are clear versions on the popular 6x3 propeller for mini quad, the clear plastic catches the light from LED illumination to create a glowing disk in the sky great for night flying. The clear plastic is extremely durable and even stronger than some colored variants. 

Features:
• Clear frosted designed for LED night illumination
• Extremely durable material
• Standardized 5mm mounting for a direct replacement

Specs:
Size: 6x3
Hub: 5mm
Rotation: CW/CCW

Included:
2 x CW rotation
2 X CCW rotation

This is a great “bread board” pin ready accelerometer for your Arduino or other microcontroller projects

Features:
• BMA180 three-axis ultra-high performance digital accelerometer, which provides a 14-bit digital output via a 4-wire SPI or 2-wire I 2 C interface
• Full scale measurement range can be set to ± 1g balance, 1.5G, 2G, 3G, 4G, 8G or 16G
• programmable wake-up
• Low-g and high-g detection
• Tap detection
• Slope detection
• Self-test capability
• The sensor also has two operating modes: low noise, low power consumption in a tiny 3x3mm 12-pin LGA package BMA180
• The sensor can be between 1.62 to 3.6V VDD and 1.2 to 3.6V VDDIO supply will typically only consume 650uA standard mode.

Specs:
Size: 21 x 10 x 2.6mm
Voltage: 1.2-3.6v
Output: SPI or I2C

*Note: This is not an original Arduino brand product.

Superheterodyne 3310 Wireless receiver module +315RF Wireless transmitter module 

Arduino 6-DOF IMU Module Attitude Control 6DOF 3205 345

*Note: This is not an original Arduino brand product.

USBasp AVR Programming Device for ATMEL Processors

Includes:
1 x USBasp Device
1 x Cable

Suits the HobbyKing Quadcopter Control Board.

Keep your Telemetry Radios safe! These cases are made out of slightly translucent ABS plastic, so you still can see TX/RX LEDs. They have a very tight fit and finish and are clearly labeled. These cases will make your setup look like Pro gear, while keeping them safe!

Designed to fit FPV Radio Telemetry Kit - 915Mhz/433MHz(#42846/42847,not included), But fits other brand Telemetry Radios as well.

Includes:
3M Foam Double-tape X1
Ground module Case X1
Air module Case X1

The flight mode switcher has been designed for open source autopilots such as APM, PX4 and Pix etc. It can switch the flight mode accurately and quickly and replaces the troublesome 2 stage and 3 stage switchers.

Users can set the parameters for the flight mode switcher on the unit and choose the most suitable modes for their requirements. The flight mode switcher features a stable performance, is easy to set up and is small and lightweight.

Typical flight modes are as follows:
• STA (Stabilized) Model will automatically level itself
• SIM (Simple) Allows you to control the movement of the model from the pilots point of view regardless of which way the model is facing
• ALT (Altitude Hold) When this mode is selected it will hold this altitude
• LOI (Loiter) Allows model to hover in the same spot on its own without any input from the pilot
• AUT (Auto) The model will follow a pre-programmed course stored in the autopilot
• RTL (Return to land) Once selected the model will return and land at the point of take-off

The flight mode switcher is simple to install on your transmitter but it is not "plug & play", there is a small amount of soldering involved inside the Tx. See under the "Files" tab for installation instructions.

Once installed on your transmitter and set up in "Mission Planner" it is very simple to use, just press the relevant mode button on the switcher and the model will go into that mode. There is an indicator light to show which mode has been selected and is in use.

Features:
• Allows the user to easily set 6 flight modes
• Simple and straightforward to install
• Compact and lightweight
• Status indicator lights

Specs:
Type: Flight Mode Switcher
Working Voltage: 3~5V
Modes: 6 selectable
Operating Temperature: -10°C~+60°C
Dimensions: 59 x 29 x 9.3mm
Weight: 13g

Included:
Flight Mode Switcher
Connection harness

KingKong Multirotor Propeller 6x4 CW/CCW Green (20pcs)

Includes:
10 x 6040 Propellers (CW)
10 x 6040 Propellers (CCW)

KingKong Multirotor Propeller 6x4 CW/CCW Red (2pcs)

Includes:
10 x 6040 Propellers (CW)
10 x 6040 Propellers (CCW)

KingKong Multirotor Propeller 6x4 CW/CCW Black (20pcs)

Includes:
10 x 6040 Propellers (CW)
10 x 6040 Propellers (CCW)

KingKong Multirotor Propeller 5x4 CW/CCW Grey (20pcs)

Includes:
10 x 5040 Propellers (CW)
10 x 5040 Propellers (CCW)

The X-CAM A10-3H Gimbal it at the top of the list when it comes to gimbals, the A10 has True continuous rotation 3-Axis ability with A/V Video link transfer. Full control over Roll, Tilt, Yaw, Mode and Zero home. And charging with A/V out transfer for the GoPro hero camera.

There are a lot of 3 Axis gimbals on the market, but only a few that use a slipper for true 360Deg continues rotation and also transfers the A/V output from the GoPro to the top controller for VTX use. The A/V line also powers/charges the GoPro. Another key feature on the X-CAM is its ability to go to zero or home using referencing sensors, this is great for when transitioning from a yaw control to a forward flight mode the gimbal will auto go to the front position.

The A10 uses an advanced method of vibration control and mounting and is a full CNC aluminum frame design with integrated motors for a light 280g weight.

If you’re serious about some aerial Photography with a GoPro this is the gimbal for you

Features:
• Continuous 360deg rotation
• A/V transfer cable with power
• 5 chs of adjustment over Sbus
• Sbus and PPM support
• Home sensors
• GUI and Upgrade ability
• Wide input voltage range
• Aluminum construction

Specs:
Weight:  280g ( without GOPRO )
Stabilization frequency:  5200Hz
Input voltage:  7.4v ~ 16.8v ( 2S ~ 4S Lipo )
Tilt travel:  +-90 degree; Roll travel:  +-45 degree
YAW travel:  360 degrees unlimited rotation

10x4.7 SF Carbon Fiber Propellers L/H and R/H Rotation (2 pcs)

These carbon props are very stiff and lighweight, they are ideal for your multi-rotor project, very efficient and give increased power with less current draw.

Specs:
Diameter: 10 inch
Pitch: 4.7 inch
Hub Thickness: 8mm
Shaft Diameter: 5~6mm (using adapters)
Weight: 10g each propeller

10x5E Carbon Fiber Propellers CW and CCW Rotation (1 pair)

These carbon props are very stiff and lighweight, they are ideal for your multi-rotor project, very efficient and give increased power with less current draw.

Specs:
Diameter: 10 inch
Pitch: 5 inch
Hub Thickness: 6.9mm
Shaft Diameter: 5~6mm (with adapters)
Weight: 15g each propeller

Note: These props are for electric use only.

These are some nice Carbon Blades for Multi-rotor projects, they are supplied as a counter rotating pair (1 left, 1 x right). These blades weigh 19g each and are very well finished! This propeller pair is supplied with contentric centering rings to ensure accurate centering.

Specs:
Diameter: 12 inch
Pitch: 6 inch
Hub thickness: 8mm
Shaft diameter: 6mm
Weight(each): 19g 

These are some nice Carbon Blades for Multi-rotor projects, they are supplied as a counter rotating pair (1 left, 1 x right). These blades weigh 15g each and are very well finished! This propeller pair is supplied with contentric centering rings to ensure accurate centering.

Specs:
Diameter: 11 inch
Pitch: 5 inch
Hub thickness: 8mm
Shaft diameter: 6mm
Weight(each): 15g 

These are some nice Carbon Blades for Multi-rotor projects, they are supplied as a counter rotating pair (1 left, 1 x right). These blades weigh 15g each and are very well finished! This propeller pair is supplied with contentric centering rings to ensure accurate centering.

Specs:
Diameter: 11 inch
Pitch: 4.7 inch
Hub thickness: 8mm
Shaft diameter: 6mm
Weight(each): 15g 

Carbon fiber propellers to suit the DJI Phantom Quadcopter, 1 pair of CW and CCW rotation, these props are 8x4.5 so can be used for other applications.

Specs:
Diameter: 8 inch
Pitch: 4.5 inch
Hub Thickness: 8mm
Shaft Diameter: Upper side 6mm/lower side 8mm
Weight: 5g each propeller

These are some nice Carbon Blades for Multi-rotor projects, they are supplied as a counter rotating pair (1 left, 1 x right). These blades weigh 17.9g each and are very well finished! This propeller pair is supplied with contentric centering rings to ensure accurate centering.

Specs:
Diameter: 13 inch
Pitch: 4 inch 
Hub thickness: 8mm
Shaft diameter: 6mm
Weight(each): 17.9g

These are some nice Carbon Blades for Multi-rotor projects, they are supplied as a counter rotating pair (1 left, 1 x right). These blades weigh 17g each and are very well finished! This propeller pair is supplied with contentric centering rings to ensure accurate centering.

Specs:
Diameter: 12 inch
Pitch: 3.8 inch
Hub thickness: 8mm
Shaft diameter: 6mm
Weight(each): 17g 

These custom made aluminum extrusions are perfect for you Multi-Rotor DIY projects, no more borrowing moms shower curtain rods...they have internal riffling (ribbing) added to remain ultra-light but have increased strength and anti-vibration characteristics as well as anodized for various color options for orientation and Bling.

Specs:
Diameter:12.8 x 12.8mm (.5inch)
Length: 600mm
Color: Black
weight: 55g

These custom made aluminum extrusions are perfect for you Multi-Rotor DIY projects, no more borrowing moms shower curtain rods...they have internal riffling (ribbing) added to remain ultra-light but have increased strength and anti-vibration characteristics as well as anodized for various color options for orientation and Bling.

Specs:
Diameter:15 x 15mm
Length: 600mm
Color: Black
weight:63g

2mm 2 Blade CNC Folding Propeller Adapter CW & CCW (Gold)

Perfect for multi-rotors, pack comes complete with M2.5 mounting screws for the folding propeller blades.

Specs:
Suits Motor Shafts: 2mm
Blade Thickness: 3mm
Blade Mounting: M2.5
Direction: 1 x Clockwise, 1 x Counterclockwise
Material: Aluminum
Color: Gold
Weight: 6g each

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 10g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 10g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3.17mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

5 x 3 Folding Propeller Blades 1 Set CW and 1 Set CCW (Blue)

Perfect for 250 style multiracers and multicopters, each blade is manufactured from nylon and is fitted with a brass insert for strength through the blade root.

Specs:
Diameter: 5ins
Pitch: 3ins
Root Thickness: 2.4mm
Mounting Hole: 2mm
Rotation: 1 pair clockwise, 1 pair counterclockwise
Color: Blue
Weight: 0.12g each blade

8 x 4.5 Folding Propeller Blades 1 Pair CW and 1 Pair CCW (Blue)

Perfect for medium size multicopters, each blade is manufactured from nylon and is fitted with a brass insert for strength through the blade root.

Specs:
Diameter: 8ins
Pitch: 4.5ins
Root Thickness: 3mm
Mounting Hole: 3mm
Direction: 1 pair clockwise, 1 pair counterclockwise
Color: Blue
Weight: 3g each blade