Drones

The all-new Multistar twin output SBEC is an advanced switching DC-DC regulator designed specifically with multirotors in mind. It will simultaneously supply a constant 5Amps at 5V and 10Amps at 12V.

It works with 2-13 cell LiPo packs and supplies an interference-free constant 5V to your receiver and 12v to a gimbal, camera, or any other 12V accessory.

Always check the input voltage of any accessory before connecting the SBEC supply to it.
 
Specs:
Type: Switching
Input Protection: Reverse polarity protection
Output (Constant): 5v/5A and 12v/10A
Input: 6v-50v (2-13 cell LiPo) 
Dimensions: 60 x 25 x 17mm
Weight: 42g

Just because you may have outgrown your Legos and Erector sets does not mean the fun has to stop. Introducing RotorBits, the modular construction set of endless possibilities. Based on the idea of standardized connections and dimensions, the only limit to what can be built is your imagination.

RotorBits can be recycled and reused into other creations, mix and matching different bits to make a Y6 or Bi-Rotor! As your collection of Bits grows and concepts evolve with plug & play easy, who knows what you can come up with? Have club competitions for creative ideas or races for fastest box to air builds. RotorBits is one idea that can never be outdated only reconfigured.

RotorBits Anodized Aluminum Construction Profile 250mm (Gray)

Specs:
Size (LxW): 250 x 10mm
Weight: 28g
Color: Gray

This is a great “bread board” pin ready accelerometer for your Arduino or other microcontroller projects

Features:
• BMA180 three-axis ultra-high performance digital accelerometer, which provides a 14-bit digital output via a 4-wire SPI or 2-wire I 2 C interface
• Full scale measurement range can be set to ± 1g balance, 1.5G, 2G, 3G, 4G, 8G or 16G
• programmable wake-up
• Low-g and high-g detection
• Tap detection
• Slope detection
• Self-test capability
• The sensor also has two operating modes: low noise, low power consumption in a tiny 3x3mm 12-pin LGA package BMA180
• The sensor can be between 1.62 to 3.6V VDD and 1.2 to 3.6V VDDIO supply will typically only consume 650uA standard mode.

Specs:
Size: 21 x 10 x 2.6mm
Voltage: 1.2-3.6v
Output: SPI or I2C

*Note: This is not an original Arduino brand product.

Superheterodyne 3310 Wireless receiver module +315RF Wireless transmitter module 

Arduino 6-DOF IMU Module Attitude Control 6DOF 3205 345

*Note: This is not an original Arduino brand product.

USBasp AVR Programming Device for ATMEL Processors

Includes:
1 x USBasp Device
1 x Cable

Suits the HobbyKing Quadcopter Control Board.

The X-CAM A10-3H Gimbal it at the top of the list when it comes to gimbals, the A10 has True continuous rotation 3-Axis ability with A/V Video link transfer. Full control over Roll, Tilt, Yaw, Mode and Zero home. And charging with A/V out transfer for the GoPro hero camera.

There are a lot of 3 Axis gimbals on the market, but only a few that use a slipper for true 360Deg continues rotation and also transfers the A/V output from the GoPro to the top controller for VTX use. The A/V line also powers/charges the GoPro. Another key feature on the X-CAM is its ability to go to zero or home using referencing sensors, this is great for when transitioning from a yaw control to a forward flight mode the gimbal will auto go to the front position.

The A10 uses an advanced method of vibration control and mounting and is a full CNC aluminum frame design with integrated motors for a light 280g weight.

If you’re serious about some aerial Photography with a GoPro this is the gimbal for you

Features:
• Continuous 360deg rotation
• A/V transfer cable with power
• 5 chs of adjustment over Sbus
• Sbus and PPM support
• Home sensors
• GUI and Upgrade ability
• Wide input voltage range
• Aluminum construction

Specs:
Weight:  280g ( without GOPRO )
Stabilization frequency:  5200Hz
Input voltage:  7.4v ~ 16.8v ( 2S ~ 4S Lipo )
Tilt travel:  +-90 degree; Roll travel:  +-45 degree
YAW travel:  360 degrees unlimited rotation

These custom made aluminum extrusions are perfect for you Multi-Rotor DIY projects, no more borrowing moms shower curtain rods...they have internal riffling (ribbing) added to remain ultra-light but have increased strength and anti-vibration characteristics as well as anodized for various color options for orientation and Bling.

Specs:
Diameter:12.8 x 12.8mm (.5inch)
Length: 600mm
Color: Black
weight: 55g

These custom made aluminum extrusions are perfect for you Multi-Rotor DIY projects, no more borrowing moms shower curtain rods...they have internal riffling (ribbing) added to remain ultra-light but have increased strength and anti-vibration characteristics as well as anodized for various color options for orientation and Bling.

Specs:
Diameter:15 x 15mm
Length: 600mm
Color: Black
weight:63g

2mm 2 Blade CNC Folding Propeller Adapter CW & CCW (Gold)

Perfect for multi-rotors, pack comes complete with M2.5 mounting screws for the folding propeller blades.

Specs:
Suits Motor Shafts: 2mm
Blade Thickness: 3mm
Blade Mounting: M2.5
Direction: 1 x Clockwise, 1 x Counterclockwise
Material: Aluminum
Color: Gold
Weight: 6g each

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 10g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3.17mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

Ever wanted to know how fast your motor is spinning?
Wished you could better select the right propeller for your motor?
Now you can more accurately tune and performance test your engine, motor, edf or heli with the Turnigy tachometer.

Measures 2 to 9 propellers.
Super easy to use.
0-99999rpm range

Features:
Ultra sharp backlit LCD
220mah Lion battery included
Auto shut-off when idle. (no more flat batteries)
Weighs only 39g.

Mini black T Connector pack (5 Pairs)

Specs:
Base Dimensions: 5mm x 8mm
Contact Dimension: 3mm x 5mm x 1mm
Rating: 10amps continuous

A JST male plug to 2.54mm pitch male jumper lead for a variety of uses.

This lead is the best solution for batteries that are slightly out of balance; simply plug it into the individual cells on the balance lead, select a 1S charge rate and you can charge them one at a time to ensure they are all at optimum charge. 

Only use this method to restore cells that are slightly out of balance and remember that there could be something wrong with one of the cells so keep a close eye on it while charging.

Overall length: 70mm

The Boom Stopper will help stop short circuits from blowing your electronics up. Simply plug in the Boom Stopper between the power source, usually your battery, and the components you are wanting to power for the first time. If there is a problem the inline 2A fuse will blow, instead of your components. When the fuse is blown the LED will light up indicating there is a short circuit and the Boom Stopper will reduce the current to a level that won't immediately damage your electronics, giving you time to remove the power supply. 

Lightweight Aluminium Round Section Spacer M3x38mm (Silver) (10pcs)

Lightweight aluminium spacers featuring a round cross section and a hex section (at each end) to fit a 5mm spanner. Ideal for use with helicopter and drone frames or similar applications where strong, accurate construction is required.

Specs:
Thread: M3
Length: 38mm
Weight: 1.5g each

The MultiStar Work Mat is a must have for any R/C hobbyist's work bench! Made from soft, grippy rubber and featuring ribbed compartments, it is perfect for containing small parts such as screws, nuts, washers and more. The backing is very grippy which will keep it from slipping on just about any surface. 

These smaller mats make excellent launch pads if you are taking off from uneven surfaces like grass or gravel.

The material is very soft and flexible allowing it to be easily rolled up for transport or storage. This makes it very easy to take with you to the race or field for on-site repairs. Never lose a screw again with the MultiStar Work Mat!

Features:
• Soft, grippy surface
• Ribbed compartments for containing small parts
• Flexible, can be rolled up for transport/storage

Specs:
Dimensions: 395 x 250mm

This latest addition to the XT60 range provides an integrated mount on the side of the XT60 with a 5mm mounting hole. This can be used to fix it to a drone frame (via a cable tie) or can be mounted to a frame stand-off. It could also be mounted to a battery tray in a plane or boat.

The guys at Bat-Safe are RC enthusiasts and came up with a safe and awesome solution to store, transport, and most importantly charge your LiPo batteries.

XT60's have been around for some time now.  These now come with a mounting base that can be screwed down to the mounting base of your drone or any other product that has a solid base. This will make connecting your battery even easier. They come in a 5 pack of male connectors making it easy to connect to your PDB or ESC's and are in a fashionable black. Made from the same high-quality nylon as the original yellow XT60, these connectors can withstand up to 60A continuous without overheating, deforming or breaking apart.

This neat adapter is perfect for converting your balance plug to a 2 pin JST connector, ideal for connecting lights and other auxillary components.

This neat adapter is perfect for converting your balance plug to a 2 pin JST connector, ideal for connecting lights and other auxillary components.

XT30 is the new connector on the block and it is perfect for Mini RC use! Forget about mini JST or Mini T-connectors or even bulky XT60 for smaller applications, we have designed the XT30 to meet the needs of the mini-revolution. From 250 class Quadcopters to foamy flyers this is the new standard for you!

Made from high-temp Nylon and gold plated spring connectors, both are included in the same injection mold at the time when forming the connector. The XT30 ensures a solid high-amp connection, perfect for applications up to and beyond 35A constant.

These straps with the Graphene logo are a great addition for securing your batteries and other items, they are also great for mounting action cams, etc to your drones.

These strong and durable straps keep batteries safely and securely affixed to the model. The locking mechanism ensures that the strap doesn’t release at the wrong time, but can easily be undone to allow the battery or component to be removed.

3.5mm Male/Female bullet on opposing ends.

3.5mm Male/Female bullet on opposing ends.

Made of TPU material, this flexible camera mount fits the Foxeer Box Cam and other action cameras. The TPU creates a soft protective layer for the camera and absorbs excess vibrations.

Transform your old micro drones into a super-fast hovercraft! A new trend is emerging in drone racing, the whoover. These are whoop hovercraft assembled from old micro multi-rotors and foam templates. Make your own today!

The PGYTECH Accessories Combo (Standard) comes with a great set of accessories to help protect DJI MAVIC AIR.