Drones

This small lightweight 4ch switch is extremely handy for auxillary functions on all sorts of models. Plug the single lead into an auxillary switched function then switch your radio on, channel 1 on the electronic switch will then be active, cycle the auxillary switch once and channel 1 goes out and channel 2 comes on, cycle the switch once more and 2 goes out and channel 3 comes and so on until it comes back to channel 1. When the radio is switched off and then switched back on the unit will default to channel 1 each time. This unit is great for switching lights on and off and other low current applications.

Please note: For this switch to work correctly you will need to set the related channel travel to +- 100%.

Specs:
Input Voltage: 4.8~7.4v
Output Voltage: 4.8~7.4v
Maximum Current: 2amps
Length: 40mm
Width: 20mm
Height: 12mm
Weight: 7g
Input Cable: 21cm (JR type plug)

Quanum Exoskeleton for RunCam

Are you worried about your RunCam action camera not surviving a hard landing?  Simply give your RunCam a rigid exoskeleton frame.

Manufactured from super light weight alloy and machined to allow easy access to all of the RunCams many functions while maintaining a clear view from the lens, this frame gives you peace of mind when you send your favorite action camera into the thick of it!

Features:
• Purpose made to fit the RunCam Action Camera
• Tough, exoskeleton style design
• Superlight Alloy
• Access to all camera functions
• Bolt together case
• Lens shield

Specs:
Dimensions: 69 x 46 x 23mm
Weight: 21.5g

5.6mm x 18mm M3 Nylon Tapped Spacer (10pc).

Perfect for mounting Multi-rotor control boards.

Need to repair crash damage to a Multi-rotor flight board or add pin outs to any other electronics project?

These header pin blocks use the industry standard spacing of 2.54mm and are designed for soldering directly into printed circuit boards (PCB's). They are supplied in 30 pin lengths which can be easily cut to seperate individual pins.

There are 5 strips per pack.

Need to repair crash damage to a Multi-rotor flight board or add pin outs to any other electronics project?

These header pin blocks use the industry standard spacing of 2.54mm and are designed for soldering directly into printed circuit boards (PCB's). They are supplied in 30 pin lengths which can be easily cut to seperate individual pins.

There are 5 strips per pack.

Need to repair crash damage to a Multi-rotor flight board or add pin outs to any other electronics project?

These header pin blocks use the industry standard spacing of 2.54mm and are designed for soldering directly into printed circuit boards (PCB's). They are supplied in 30 pin lengths which can be easily cut to seperate individual pins.

There are 5 strips per pack.

Need to repair crash damage to a Multi-rotor flight board or add pin outs to any other electronics project?

This Header pin type is perfect for repairing Servo pins on most 4 (or more) channel receivers.

These header pin blocks use the industry standard spacing of 2.54mm and are designed for soldering directly into printed circuit boards (PCB's). They are supplied in 30 pin lengths which can be easily cut to seperate individual or groups of pins.

There are 5 strips per pack.

Why settle for only being able to charge your DJI Phantom 2 batteries at home?

The Quanum DC Field Charger charger allows you to quickly and easily charge your Phantom 2 batteries at the field from just about any 10~26VDC power source! This means easy battery charging from your car or truck's starter battery!

Simply connect the alligator clips to your vehicle's starter battery and the output lead to the Phantom 2 battery. The output lead features a polarity-protected plug which prevents improper connection. This charger provides up to 4A of current, matching that of the original DJI Phantom 2 battery charger.

This compact, lightweight power supply filter helps clean up dirty DC current that often causes lines in wireless video images. The filter is an LC type that uses large value inductor and capacitor components. Their values are robust enough to remove moderate amounts of power supply noise.

The filter reduces DC-DC switcher supply ripple and helps clean noisy power from a shared battery. For example, if your robot or R/C model's 12V motor battery also powers the video camera and A/V transmitter, then this LC filter can help reduce the video "noise" that may appear when the motor is running.

Note: Installations with severe power supply noise may not be fully cured with this filter. In such cases a shared battery should be avoided.

Features:
• L-C Filter circuit reduces DC supply noise
• Built-in Reverse Polarity protection
• Supports up to 14 VDC at 1.7 Amp (maximum)
• Compact design

Specs:
Voltage drop over filter: 225mV at 900mA
Impedence/ESR: 0.06Ohm at 100kHz/16V
Ripple Current: 1190mA
DC Resistance: 0.25 Ohm/path
Dimensions: 38x12.5x11.5mm
Weight: 6.4g

HobbyKing™ Micro BEC 5V/1A

This great new switching mode BEC is the smallest yet made by HobbyKing. Our engineers developed this with micro and race quads in mind. It is extremely small and light weight but gives you excellent power for the Fight Controller, RX, etc.

Specs:
Input: 2-4cells Lipoly
Output (Constant): 5v/1A
Type: Switching
Input protection: Reverse polarity protection
Size: 10x9x7mm
Weight: 1.4g (wires included)

Multistar 1704 V2 Prop Adapter Set 2 x CW / 2 x CCW.

High-quality prop adapter set to fit the Multistar 1704 range of motors. The package contains 2 x clockwise and 2 x counter-clockwise adapters and a complete set of the required fixing screws.

Looking for the professional finish on your next quadcopter project? look no further! This simple and easy to install light module set, will not only provide you with a proffesional look but will also allow your quadcopter to be seen in any conditions with its super bright LEDs

The LED flash light set offers a wide voltage input range from 2-6s and is suitable for quadcopters up to 500mm diameter. 

Features:
• Suitable for quadcopters up to 500mm diameter
• Wide input voltage, 2-6s capability
• High efficiency frequency conversion circuit
• Low power consumption
• No flashing delay or brightness reduction
• High power output
• Simple frequency adjustment

Specs:
LED Cable Length: 500mm
System Weight: 48g
Input Voltage 7.4v ~ 22.2v

Protect your multirotor ESC / battery connectors from impact or prop damage with these handy
PCB's. Simply solder your Male XT90 connector directly to the board and secure to your multirotor
frame with some 3mm nuts and bolts.

Specs:
Length: 35mm
Width 10mm
Depth: 1.5mm
Hole Spacing: 35mm max

TF Model ESC and LED lighting power distribution board suitable for most quads and multi-rotors including SMACK TF250, OrcaTF280, TF650, TF680 and TF690.  A 3 position control channel can be setup to change the LED from Solid, Slow blinking and fast blinking LED lights.

Specs:
Dimensions: 50 x 50mm
Weight: 14g
ESC Output : 6
5V Output : 1
12V Output : 1
Mounting Holes : 45mm

Nylon Spacer 20mm M3 F/F Red (10pcs)

Specs:
Shape: Hex
Length: 20mm
Screw Thread: M3 Female/Female
Qty: 10 

Nylon Spacer 10mm M3 M/F Orange (10pcs)

Specs:
Shape: Hex
Length: 10mm
Screw Thread: M3 Male/Female
Qty: 10 

The Boom Stopper will help stop short circuits from blowing your electronics up. Simply plug in the Boom Stopper between the power source, usually your battery, and the components you are wanting to power for the first time. If there is a problem the inline 2A fuse will blow, instead of your components. When the fuse is blown the LED will light up indicating there is a short circuit and the Boom Stopper will reduce the current to a level that won't immediately damage your electronics, giving you time to remove the power supply. 

Lightweight Aluminium Round Section Spacer M3x38mm (Silver) (10pcs)

Lightweight aluminium spacers featuring a round cross section and a hex section (at each end) to fit a 5mm spanner. Ideal for use with helicopter and drone frames or similar applications where strong, accurate construction is required.

Specs:
Thread: M3
Length: 38mm
Weight: 1.5g each

The MultiStar Work Mat is a must have for any R/C hobbyist's work bench! Made from soft, grippy rubber and featuring ribbed compartments, it is perfect for containing small parts such as screws, nuts, washers and more. The backing is very grippy which will keep it from slipping on just about any surface. 

These smaller mats make excellent launch pads if you are taking off from uneven surfaces like grass or gravel.

The material is very soft and flexible allowing it to be easily rolled up for transport or storage. This makes it very easy to take with you to the race or field for on-site repairs. Never lose a screw again with the MultiStar Work Mat!

Features:
• Soft, grippy surface
• Ribbed compartments for containing small parts
• Flexible, can be rolled up for transport/storage

Specs:
Dimensions: 395 x 250mm

This latest addition to the XT60 range provides an integrated mount on the side of the XT60 with a 5mm mounting hole. This can be used to fix it to a drone frame (via a cable tie) or can be mounted to a frame stand-off. It could also be mounted to a battery tray in a plane or boat.

This is a great “bread board” pin ready accelerometer for your Arduino or other microcontroller projects

Features:
• BMA180 three-axis ultra-high performance digital accelerometer, which provides a 14-bit digital output via a 4-wire SPI or 2-wire I 2 C interface
• Full scale measurement range can be set to ± 1g balance, 1.5G, 2G, 3G, 4G, 8G or 16G
• programmable wake-up
• Low-g and high-g detection
• Tap detection
• Slope detection
• Self-test capability
• The sensor also has two operating modes: low noise, low power consumption in a tiny 3x3mm 12-pin LGA package BMA180
• The sensor can be between 1.62 to 3.6V VDD and 1.2 to 3.6V VDDIO supply will typically only consume 650uA standard mode.

Specs:
Size: 21 x 10 x 2.6mm
Voltage: 1.2-3.6v
Output: SPI or I2C

*Note: This is not an original Arduino brand product.

Superheterodyne 3310 Wireless receiver module +315RF Wireless transmitter module 

Arduino 6-DOF IMU Module Attitude Control 6DOF 3205 345

*Note: This is not an original Arduino brand product.

USBasp AVR Programming Device for ATMEL Processors

Includes:
1 x USBasp Device
1 x Cable

Suits the HobbyKing Quadcopter Control Board.

The X-CAM A10-3H Gimbal it at the top of the list when it comes to gimbals, the A10 has True continuous rotation 3-Axis ability with A/V Video link transfer. Full control over Roll, Tilt, Yaw, Mode and Zero home. And charging with A/V out transfer for the GoPro hero camera.

There are a lot of 3 Axis gimbals on the market, but only a few that use a slipper for true 360Deg continues rotation and also transfers the A/V output from the GoPro to the top controller for VTX use. The A/V line also powers/charges the GoPro. Another key feature on the X-CAM is its ability to go to zero or home using referencing sensors, this is great for when transitioning from a yaw control to a forward flight mode the gimbal will auto go to the front position.

The A10 uses an advanced method of vibration control and mounting and is a full CNC aluminum frame design with integrated motors for a light 280g weight.

If you’re serious about some aerial Photography with a GoPro this is the gimbal for you

Features:
• Continuous 360deg rotation
• A/V transfer cable with power
• 5 chs of adjustment over Sbus
• Sbus and PPM support
• Home sensors
• GUI and Upgrade ability
• Wide input voltage range
• Aluminum construction

Specs:
Weight:  280g ( without GOPRO )
Stabilization frequency:  5200Hz
Input voltage:  7.4v ~ 16.8v ( 2S ~ 4S Lipo )
Tilt travel:  +-90 degree; Roll travel:  +-45 degree
YAW travel:  360 degrees unlimited rotation

These custom made aluminum extrusions are perfect for you Multi-Rotor DIY projects, no more borrowing moms shower curtain rods...they have internal riffling (ribbing) added to remain ultra-light but have increased strength and anti-vibration characteristics as well as anodized for various color options for orientation and Bling.

Specs:
Diameter:12.8 x 12.8mm (.5inch)
Length: 600mm
Color: Black
weight: 55g

These custom made aluminum extrusions are perfect for you Multi-Rotor DIY projects, no more borrowing moms shower curtain rods...they have internal riffling (ribbing) added to remain ultra-light but have increased strength and anti-vibration characteristics as well as anodized for various color options for orientation and Bling.

Specs:
Diameter:15 x 15mm
Length: 600mm
Color: Black
weight:63g

2mm 2 Blade CNC Folding Propeller Adapter CW & CCW (Gold)

Perfect for multi-rotors, pack comes complete with M2.5 mounting screws for the folding propeller blades.

Specs:
Suits Motor Shafts: 2mm
Blade Thickness: 3mm
Blade Mounting: M2.5
Direction: 1 x Clockwise, 1 x Counterclockwise
Material: Aluminum
Color: Gold
Weight: 6g each

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 10g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3.17mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)