Aircraft

This handy little accessory will allow you to easily split a single receiver channel output into five. A handy accessory for those building multicopters as it gives you an easy way to program the throttle range into your ESC's all together prior to fitting them to your frame. It can also be used as a splitter in LED lighting systems.

Spec:
Lead length: 60mm
Weight: 3g

Mini black T Connector pack (5 Pairs)

Specs:
Base Dimensions: 5mm x 8mm
Contact Dimension: 3mm x 5mm x 1mm
Rating: 10amps continuous

Super flexible 26AWG twisted silicone male to male servo lead. These are specifically made as signal leads for RX to Flight controller connections, the light 26AWG silicone wire is so flexible it transfers virtually no vibration to the Flight controller, well the twist helps reduce inducted noise. If used in conjunction of having only one lead vertical and the other leads turned on their side for signal only, makes for a clean and minimal vibration transfer installation. Or better yet a single CPPM/SBUS single lead. 

Specs:
Length: 130mm(black/red/white)
Connection: Male JR style plug on each end.

Super flexible 26AWG twisted silicone male to male servo lead. These are specifically made as signal leads for RX to Flight controller connections, the light 26AWG silicone wire is so flexible it transfers virtually no vibration to the Flight controller, well the twist helps reduce inducted noise. If used in conjunction of having only one lead vertical and the leads turned on their side for signal only makes for a clean and minimal vibration transfer installation, or better yet a single CPPM/SBUS single lead.

Specs:
Length: 80mm(black/red/white)
Connection: Male JR style plug on each end.

This data cable allows you to connect our 433/915MHz V1.1 Radio Telemetry Kits to your Walkera X800 GPS Quadcopter. The X800 flight controller has a data port which actually functions as a standard APM UART connection. The port is a specialized 4-pin connector which will not fit standard Molex style plugs.

This data cable will allow you to plug directly to the X800 FC data port and to our 433/915MHz V1.1 Radio Telemetry air module, allowing full access to wireless telemetry functionality of the APM based X800 flight controller.

Specs:
Connection: 4-pin Walkera style plug to 6-pin Molex style plug
Length: 180mm

*Note: Please see related items below for the compatible 433/915MHz V1.1 Radio Telemetry Kits.

A JST male plug to 2.54mm pitch male jumper lead for a variety of uses.

This lead is the best solution for batteries that are slightly out of balance; simply plug it into the individual cells on the balance lead, select a 1S charge rate and you can charge them one at a time to ensure they are all at optimum charge. 

Only use this method to restore cells that are slightly out of balance and remember that there could be something wrong with one of the cells so keep a close eye on it while charging.

Overall length: 70mm

The Vortex FPV Racer from ImmersionRC is an incredible piece of kit for the serious competitor, but like all things flying the ocassional mishap is inevitable!

This crash kit is a convenient way to keep a stock of all of those plastic parts most likely to be damaged in a serious "departure from controlled flight"

Included are all parts which mount the motors to the carbon fiber arms, the plastic pivot points, foldable arm clips, and all other plastic parts.

No carbon fiber parts are included (see Crash Kit 2.)

Included:
1 x Front bumper (FR4)
2 x Side plates
8 x Arm clips
4 x Arm pivot tops
4 x Arm pivot bottoms
4 x Landing bumpers
4 x Landing mounts
4 x Motor mounts
8 x Hex bushes
1 x Camera support base
1 x Camera support arm
4 x Damper pins
4x Damper circlip
4x Screw HA2x8
4x Screw HA2x6

This handy little device allows you to program your ZYX Flybarless Controller wirelessly via Bluetooth connectivity with your Android device. Now there is no longer a need to bring your PC to the field for making programming adjustments!

Simply plug this device into the data port of your ZYX unit, install the free ZYX programming app on your Android mobile device and you are all set! It's that easy. You will be able to access all of the same programming options that are available on the PC software directly from your Android device.

This is a must have for any ZYX user with an Android mobile device!

Features:
• Compact size
• Easy to use
• Bluetooth wireless connectivity
• Free Android app available
• Eliminates the need to bring your PC to the field

Specs:
Dimensions: 32x14x5mm
Weight: 3g

*Note: This device currently supports Android 1.6 and above versions of the operating system.

Tarot 450 Pro/Pro V2 DFC Feathering Spindle (TL48016)

The Tarot 450 Pro/Pro V2 DFC feathering spindles are uniquely designed to reduce the probability of the retaining screws coming loose.

Includes:
450 DFC Feathering Spindle x 1 (4x54mm)
Thrust Bearing x 2 (4x8x3.5mm)
Thrust Bearing Circlip x 2 (M4x6.5x1.5mm)
M2.5 Socket Head Screws x 2 (M2.5x6mm)
Washers x 2 (4x7.5x1mm)

Telemicro 520mm - Replacement Spinner

Suit HobbyKing Bixler 2

Spec.
Length: 41mm / 18mm(Horn Only)
Clip Size: 12 x 9.5mm

Hobbyking Bixler 2 EPO 1500mm - Replacement Pushrod Set

HobbyKing Bixler 2 EPO 1500mm -  Replacement Flap Hinges (6pcs/bag)

Works for both Bixler 2 and Bix3 models.

Hobbyking Bixler 2 EPO 1500mm - Replacement Aileron Hinges (10pcs/bag)

Solo Pro 100 Tail Rotor Blade

Solo Pro FP II Main Rotor Blade Set

Deluxe Helicopter Starter Shaft with One way Bearing

Suits standard starter or electric drill. Features a removable shaft and one way bearing.

Spec:
Length: 250mm (Total lenth)
Hex size: 6mm
Starter sfaft: 8mm

Looking to make your video platform ultra-smooth? This is the ultimate in smooth high pole count purpose built brushless gimbal motors.

The 2804 motor comes with flush mounting so any DIY to PRO projects are simple and straight forward, it also comes with the standard female connector pre-installed, So wiring is as simple as plugging it in. It’s a perfect match to our Brushless Gimbal Stabilization Board and IMU.

The 2804 is the perfect size for cameras around 100-300 grams (GoPro style).

Spec:
Poles: 12N14P
KV(RPM/V): 210
Resistance: 10.4omh
Weight: 35g
Wire: 0.19mm
Torque: 240g
Bottom holes center to center: 16mm and 19mm
Top holes center to center: 12mm

Durafly Auto-G2 Gyrocopter 821mm - Replacement Battery Hatch

FP100 Helicopter Tail Fin

The Q222K Spaceship is a real entry-level FPV quadcopter with some features that have become the standard with more expensive models including altitude hold, Headless Mode, and automatic one key return.

With stable hovering, automatic take-off, and WiFi FPV for aerial photography this is a perfect FPV training quad. It has a 720P HD camera delivering excellent images to help make the entire FPV experience more immersive and enjoyable. Simply connect your smartphone WiFi to view the entire flight on your phone in real-time.

Pioneer 1020mm - Replacement Horizontal Stabilizer

La Belle Dame 1180mm - Propeller Nuts

Just because you may have outgrown your Legos and Erector sets does not mean the fun has to stop. Introducing RotorBits, the modular construction set of endless possibilities. Based on the idea of standardized connections and dimensions, the only limit to what can be built is your imagination.

RotorBits can be recycled and reused into other creations, mix and matching different bits to make a Y6 or Bi-Rotor! As your collection of Bits grows and concepts evolve with plug & play easy, who knows what you can come up with? Have club competitions for creative ideas or races for fastest box to air builds. RotorBits is one idea that can never be outdated only reconfigured.

The Quad plate has 4 10x10mm slots for motor arms and 45x45mm posts for flight controller mounting. The center plate as other provisions for mounting other Bits and holes at 10mm intervals.

Specs:
Size: 100x100mm
Weight: 77g
Color: Green

The all-new Multistar twin output SBEC is an advanced switching DC-DC regulator designed specifically with multirotors in mind. It will simultaneously supply a constant 5Amps at 5V and 10Amps at 12V.

It works with 2-13 cell LiPo packs and supplies an interference-free constant 5V to your receiver and 12v to a gimbal, camera, or any other 12V accessory.

Always check the input voltage of any accessory before connecting the SBEC supply to it.
 
Specs:
Type: Switching
Input Protection: Reverse polarity protection
Output (Constant): 5v/5A and 12v/10A
Input: 6v-50v (2-13 cell LiPo) 
Dimensions: 60 x 25 x 17mm
Weight: 42g

Just because you may have outgrown your Legos and Erector sets does not mean the fun has to stop. Introducing RotorBits, the modular construction set of endless possibilities. Based on the idea of standardized connections and dimensions, the only limit to what can be built is your imagination.

RotorBits can be recycled and reused into other creations, mix and matching different bits to make a Y6 or Bi-Rotor! As your collection of Bits grows and concepts evolve with plug & play easy, who knows what you can come up with? Have club competitions for creative ideas or races for fastest box to air builds. RotorBits is one idea that can never be outdated only reconfigured.

RotorBits Anodized Aluminum Construction Profile 250mm (Gray)

Specs:
Size (LxW): 250 x 10mm
Weight: 28g
Color: Gray

Just because you may have outgrown your Legos and Erector sets does not mean the fun has to stop. Introducing RotorBits, the modular construction set of endless possibilities. Based on the idea of standardized connections and dimensions, the only limit to what can be built is your imagination.

RotorBits can be recycled and reused into other creations, mix and matching different bits to make a Y6 or Bi-Rotor! As your collection of Bits grows and concepts evolve with plug & play easy, who knows what you can come up with? Have club competitions for creative ideas or races for fastest box to air builds. RotorBits is one idea that can never be outdated only reconfigured.

Composite fixture plate for mounting, bracing or assembly based on the standard 10mm hole spacing of RotorBits. 

Specs:
Size: 56x56mm
Thickness: 1.5mm
Angles: 90deg cross
Weight: 7.5g
Color: Black mate
Hole size: M2.5
Hole spacing: 10mm (RotorBits standardized)
Bag of two

R/C Helicopter Pitch Gauge, a must for when setting up your RC helicopter.

Specs:
Range: +12°, -12°
Material: Plastic
Suits: Most mini-helicopters

These new upswept upgrade arms provide improved stability and faster forward flight. The arms are manufactured from toughened plastic which provides added strength.  

The arms are designed to fit DJI Flamewheel style multirotor frames such as the V500 / H550 Frames

Specs:
Length: 210mm
Weight: 62g (per arm)
Color: White

Main Gear - Walkera V120D02S 3D Mini Helicopter

HM-V120D02S-Z-10

This amazing micro helicopter is packed with features to make it fun and easy to fly. The flybarless system is controlled and stabilized using a 6-axis gyro system which gives it a stability rarely seen before in a small RC helicopter. The K200 also has a barometric pressure sensor for altitude hold and an optical sensor for position hold. This coupled with the 6-axis gyro, makes it the perfect choice for the novice pilot.

The XK K110S CP micro helicopter with collective pitch and a brushless motor is the perfect choice for those pilots who want to progress on the exciting journey of learning to fly RC helicopters. Being an upgraded version of the popular K110, the K110S is very capable of performing advanced aerobatics and 3D flight, but it is also equally at home flying as a stable intermediate training platform. The XK K110S is stabilized using a state-of-the-art gyro system that has the ability to be switched from 6-axis for super stable flight, to 3-axis for aerobatic and wild 3D flight. A very handy feature when you have the 6-axis gyro selected is "Hover Mode", at the flick of a switch on the transmitter the K110S will sit in a stable hover without any inputs from you on the control sticks.

For those wishing to fly an RC helicopter that looks like the real thing, the AS350 from XK is just the ticket. This scale-looking model which includes a collective-pitch 3-blade rotor-head, is based on the Eurocopter AS350 Écureuil (or Squirrel) light utility helicopter. Being scale though does not hold the AS350 back, with its powerful brushless motor set up it is still very capable of flying aerobatics and advanced 3D maneuvers. The XK AS350 is stabilized using a state-of-the-art gyro system that has the ability to be switched from a 6-axis mode for super stable flight to a 3-axis mode which allows for aerobatic and wild 3D flying. A very handy feature when you have the 6-axis gyro selected is "Hover Mode", at the flick of a switch on the transmitter the AS350 will sit in a stable hover without any inputs from you on the control sticks.

The XK K100 6ch CP palm-size helicopter with collective pitch is the perfect choice for those pilots who want to progress on their journey of learning to fly RC helicopters. The K100 CP is very capable of performing advanced aerobatics and 3D flight, but it is also equally at home flying as a stable intermediate training platform. Using a state-of-the-art switchable gyro stabilization system, it has the ability to be switched from 6-axis for super stable flight, to 3-axis for aerobatics and wild 3D flight. Also, when you select the 6-axis gyro system, you can select "Hover Mode", at the flick of a switch on the transmitter the K100 will sit in a stable hover without any inputs from you on the control sticks.