Aircraft

Protect your multirotor ESC / battery connectors from impact or prop damage with these handy
PCB's. Simply solder your Male XT90 connector directly to the board and secure to your multirotor
frame with some 3mm nuts and bolts.

Specs:
Length: 35mm
Width 10mm
Depth: 1.5mm
Hole Spacing: 35mm max

By harnessing the power and imagination of the open source community, OpenPilot have created a new generation of powerful, low cost flight controller known as CopterControl that is suitable for multirotors, helicopters and fixed wing aircraft.

The Open Pilot CC3D Revolution (Revo) is the result of 1000's of hours of R&D work by the open source community, for the benefit of everyone and provides a robust base for commercial, research and hobby projects alike.

The Revo flight controller features state of the art hardware and software, backed by the Open Pilot GCS FC System and boasts position hold and 3D waypoint navigation among its many features. It is a full 10DOF with gyroscope, accelerometer, magnetometer and barometric pressure sensors.

The Revo uses the STM32F4 CPU which uses a hardware floating point unit (FPU,) that represents a huge advancement for hobby-class autopilots. This FPU allows precise, low-latency processing of real-life measurements using advanced attitude estimation algorithms.

In addition to an integral FPU, the STM32F405RGT6 chip has the ARM Cortex-M4 core at 210MIPS and saturation arithmetic DSP functions.

The CPU has a range of built-in hardware modules that can be programmed once and function independently, requiring little to no CPU overhead.
These include 14 multi-channel timers, 3 synchronous-sampling ADCs serving up to 24 channels, 2 DAC, matrix memory controller with 16-stream DMA.
Communication modules include USB2.0, 3 x I2C, 3 x SPI, 4 x USART, 2 x CAN and SIDO. All these modules can be configured for accessing the chip pins using a flexible switch matrix, or disabled to save power. USB connectivity ensures that software updates and settings are straightforward to make in the GCS (Ground Control Station.)

The flight controller features a built-in 433MHz OPLink Modem and uses the standard OpenPilot footprint so has the same dimensions and mounting holes as the OpenPilot CC, CC3D, GPS, OSD and PipX boards.  

The Revo has an incredible array of functions to manage all of your flight parameters, and while it doesn't have the kitchen sink, it does a real time hardware calendar if you ever feel the need for a wake up flight!

Features:
• Open source development
• Flexi-IO Port for input/output
• MainPort (Telemetry) serial USART w/adjustable baud rate.
• FlexiPort for telemetry funtions
• 433MHz RF output
• Power Sensor/Sonar Port
• STM32F4 32 bit  CPU
• ARM32 powered digital packet processor
• USB2.0, I2C, SPI, USART, CAN and SIDO communication modules
• 14 Multi-channel timers
• 3-Axis gyro
• 3-Axis accelerometer
• 3-Axis Magnetometer
• Barometric pressure sensor
• PWM/PPM for configuration with Futaba, FrSky, Spektrum (inc satellite) receivers and many others.

Specs:
Input voltage: 5 ~ 8.4V
Telemetry link: 433MHz
Power connectors: JST-SH 4-pin
Antenna connector: SMA
Dimensions: 36 x 36mm
Weight: 9g

Included:
OpenPilot CC3D Revolution (Revo) Flight controller w/Internal 433Mhz Radio
10 Pin cable
4 Pin cable
Antenna extension cable
Antenna

Full configurations instructions can be found in the  OpenPilot manual:

http://opwiki.readthedocs.org/en/latest/user_manual/index.html

Quanum MT series motors are Spec built by DYS, well known in the industry for their quality and performance.

The MT line uses quality NMB bearings, high pole counts for torque and smooth operation and all have standardized universal mountings in their given size. Quanum has spec’d the motors with N42sh magnets and .2mm laminations for optimal efficiency. The MT’s also have ample motor wire length for a cut to fit installation, with included bullet connectors and shrink tube. Another great feature is that Quanum spec’d all the motors to come with mounting hardware in various lengths, as well as both hub and direct mount propeller options, so installation is a snap.

Each Quanum motor is QC checked for balance, wind, performance and mechanical tolerance. The DYS brand is well known for their BE series and the new spec built MT line will set new standards of value vs performance.

Features:
• High Power N42sh magnets
• Precision NMB bearings
• .2mm laminations for optimal efficiency
• Ample cut to length motor wires for a clean install
• Direct mount propeller or Hub style compatible
• Multi-length mounting hardware included

Specs:
KV(RPM/V): 2000KV
Lipo cells: 2-3S
Max Power: 84.4W
Max Amps: 7.6A
No Load Current: 0.6/11.1V
Internal Resistance: 0.98ohm
Number of Poles: 14
Dimensions(Dia.xL):28 x 17mm
Motor Shaft: 2mm
prop shaft: 5mm CW prop adapter
Weight: 33g
bolt hole spacing: 16*19 M3
Lamination thickness:  0.2mm
Magnets: 42SH
Wire: 18AWG
Connector: 3.5mm bullet

PROP         Power/PWM     Voltage (V) Current (A)   Thrust (gf)   RPM
6x4.5 STD        10                 11.1          0.44          27.15        3451
6x4.5 STD        25                 11.1          2.62         163.01       8336
6x4.5 STD        50                 11.1          6.66           349.5      12040
6x4.5 STD        75                 11.1        13.53           571.3      15409
6x4.5 STD      100                  11.1       15.74          633.98      15935
6x4.5 STD        10                 14.8          0.59           44.33       4449
6x4.5 STD        25                 14.8            3.7         260.26      10489
6x4.5 STD        50                 14.8          9.75         549.91      14962
6x4.5 STD        75                 14.8         20.28         874.48      18361
6x4.5 STD      100                 14.8         22.45         914.19      18943

FX071C 2.4GHz 4CH Flybarless RC Helicopter Replacement Plastic Main Frame Parts.

FX070C 2.4GHz 4CH Flybarless RC Helicopter Replacement Tail Boom Set.

FX070C 2.4GHz 4CH Flybarless RC Helicopter Replacement Swashplate.

FX070C 2.4GHz 4CH Flybarless RC Helicopter Replacement Fuselage.

Had an accident with your FX070C?, this is a replacement fuselage that consists of the 2 sides and the tailboom, it does not include the front screen or the weapons.

FX070C 2.4GHz 4CH Flybarless RC Helicopter Replacement Transmitter (Mode1 & Mode2).

Changes easily from Mode 1 to Mode 2 just by sliding a switch on the back of the transmitter.

Durafly® ™ Supermarine Spitfire Mk 24 - Replacement Split Flaps (1set)

Volantex Phoenix 2000  Replacement Spinner.

TF Model ESC and LED lighting power distribution board suitable for most quads and multi-rotors including SMACK TF250, OrcaTF280, TF650, TF680 and TF690.  A 3 position control channel can be setup to change the LED from Solid, Slow blinking and fast blinking LED lights.

Specs:
Dimensions: 50 x 50mm
Weight: 14g
ESC Output : 6
5V Output : 1
12V Output : 1
Mounting Holes : 45mm

This is the carbon fiber main frame base plate for the HK-550GT helicopter.

Walkera F210 Racing Quad – DEVO-RX713 Receiver

Part No: F210-Z-25

Walkera F210 Racing Quad – HD Mini Camera (700TVL)

Part No: F210-Z-31

JST-SH 3Pin Socket (Surface Mount) (5pcs)

Although this is a  surface mount socket it can also be used with thin extension wire leads. The soldered connections must be protected with heat shrink sleeving.

There are lots of applications for these sockets from using on robotic control boards to fixing connectors on flight controllers. They come in a number of different pin numbers.

Specs:
Type: Male
Number of Pins: 3
Pin Spacing: 1mm
Socket Size: 5.5x4.5x3.1mm

JST-SH 5Pin Socket (Surface Mount) (5pcs)

Although this is a  surface mount socket it can also be used with thin extension wire leads. The soldered connections must be protected with heat shrink sleeving.

There are lots of applications for these sockets from using on robotic control boards to fixing connectors on flight controllers. They come in a number of different pin numbers.

Specs:
Type: Male
Number of Pins: 5
Pin Spacing: 1mm
Socket Size: 7.5x4.5x3.1mm

JST-SH 6Pin Socket (Surface Mount) (5pcs)

Although this is a  surface mount socket it can also be used with thin extension wire leads. The soldered connections must be protected with heat shrink sleeving.

There are lots of applications for these sockets from using on robotic control boards to fixing connectors on flight controllers. They come in a number of different pin numbers.

Specs:
Type: Male
Number of Pins: 6
Pin Spacing: 1mm
Socket Size: 8.5x4.5x3.1mm

JST-SH 8Pin Socket (Surface Mount) (5pcs)

Although this is a  surface mount socket it can also be used with thin extension wire leads. The soldered connections must be protected with heat shrink sleeving.

There are lots of applications for these sockets from using on robotic control boards to fixing connectors on flight controllers. They come in a number of different pin numbers.

Specs:
Type: Male
Number of Pins: 8
Pin Spacing: 1mm
Socket Size: 10.5x4.5x3.1mm

Spare Part - Cowl for Spitfire Mk5 Desert Scheme version

JST-SH 4Pin Socket (Surface Mount) (5pcs)

Although this is a  surface mount socket it can also be used with thin extension wire leads. The soldered connections must be protected with heat shrink sleeving.

There are lots of applications for these sockets from using on robotic control boards to fixing connectors on flight controllers. They come in a number of different pin numbers.

Specs:
Type: Male
Number of Pins: 4
Pin Spacing: 1mm
Socket Size: 6.5x4.5x3.1mm

JST-SH 5Pin Female Plug with 200mm Wire Pigtail (5pcs)

JST-SH 8Pin Female Plug with 200mm Wire Pigtail (5pcs)

These plugs come fitted with 200mm wire tails.

There are lots of applications for these plugs from using with robotic control boards to fixing plugs for flight controllers. They come in a number of different pin numbers.

Specs:
Type: Female
Number of Pins: 8
Pin Spacing: 1mm

JST-SH 5Pin Female (Plug and Crimp) (5pcs)

These plugs come with crimp style pins.

There are lots of applications for these plugs from using with robotic control boards to fixing plugs for flight controllers. They come in a number of different pin numbers.

Specs:
Type: Female
Number of Pins: 5
Pin Spacing: 1mm

JST-SH 6Pin Female (Plug and Crimp) (5pcs)

These plugs come with crimp style pins.

There are lots of applications for these plugs from using with robotic control boards to fixing plugs for flight controllers. They come in a number of different pin numbers.

Specs:
Type: Female
Number of Pins: 6
Pin Spacing: 1mm

JST-SH 8Pin Female (Plug and Crimp) (5pcs)

These plugs come with crimp style pins.

There are lots of applications for these plugs from using with robotic control boards to fixing plugs for flight controllers. They come in a number of different pin numbers.

Specs:
Type: Female
Number of Pins: 8
Pin Spacing: 1mm

KingKong Self-tightening Prop Adapters (CW/CCW) (2 pairs)

These are designed for KingKong propellers and have two lugs on the bottom side.

Includes:
2 x Self-tightening Prop Adapters (CW)
2 x Self-tightening Prop Adapters (CCW)

Excellent double sided tape for outdoor use. This tape is strong and padded.

Great for using on applications that need a bit of padding such as mounting receivers, flight controllers or ESCs. 

Specs:
Width: 20mm
Length: 1500mm

Nylon Spacer 20mm M3 F/F Red (10pcs)

Specs:
Shape: Hex
Length: 20mm
Screw Thread: M3 Female/Female
Qty: 10 

Nylon Spacer 10mm M3 M/F Orange (10pcs)

Specs:
Shape: Hex
Length: 10mm
Screw Thread: M3 Male/Female
Qty: 10 

Durafly™ T-28 Trojan 1100mm V2 - Horizontal Tail

Durafly™ T-28 Trojan 1100mm V2 - D3536-750kv Motor inc X Mount

Durafly™ T-28 Trojan 1100mm V2 - Canopy inc FPV Pilot Tray.

Please note: This canopy will also fit the Durafly T-28 Trojan Naval Aviation Centennial Edition, but of course the color scheme is different.

Durafly™ T-28 Trojan 1100mm V2 - Control and Mounting Accessories