Workbench

Model JET Pilot 1/6 (Green) (H80 x W68 x D37mm)

Made with what seems to be a flexible rubber or plastic.
Well detailed and nicely painted.
A good addition to any plane.

Specs
Heigth: 80mm
Width: 68mm
Depth: 37mm
Weight: 29g

Ultra Light Parkfly Pilot (Green) (H30 x W37 x D18mm) - Perfect for even the lightest parkfly model!

Specs
Height: 30mm
Width: 37mm
Depth: 18mm
Weight: 2g

Ultra Light Parkfly Pilot (Red) (H30 x W37 x D19mm) - Perfect for even the lightest parkfly model!

Specs
Height: 30mm
Width: 37mm
Depth: 19mm
Weight: 2g

Parkfly Classic Era Pilot (Red) (H37 x W40 x D22mm)

Specs
Height: 37mm
Width: 40mm
Depth: 22mm
Weight: 6g

Parkfly Luftwaffe Pilot (H38 x W39 x D23mm)

Specs
Height: 38mm
Width: 39mm
Depth: 23mm
Weight: 7g

This is a very neat device for securing your models hatches. This latch is spring loaded so once latched your canopy stays put!

Specs:
Dimensions: 26 x 16 x 8mm + 15mm pin length 
Material: Aluminum

This is a very neat device for securing your models hatches. This latch is spring loaded so once latched your canopy stays put!

Specs:
Dimensions: 23.5 x 13 x 8mm + 8mm pin length
Material: Plastic / Steel

This is a very neat device for securing your models hatches. This latch is spring loaded so once latched your canopy stays put!

Specs:
Dimensions:  26x16x10mm + 10mm pin Length
Material: Plastic / brass

These are used to help route cables and hoses within your models. These anchors are self adhesive and allow you to pass a cable tie through the anchor, then around the cable or hose you wish to hold in position.

Handy for use in both your models and the workshop!

Dimensions: 25 x 25mm 

Self Assembly Pedal Operated Bungee Launch System/Ramp for FPV/Glider and EDF Models - Hand launching models can be a tricky business and most flyers have had it all go wrong for them at some point, this great launch system is easy to transport & field assemble and allows you to launch totally solo with the peace of mind of adequate airspeed every time for a succesful launch, everything you need is included!

Dimensions once Assembled:
Ramp Length - 1060mm
height at rear - 240mm
height at front -  460mm
width of launch rails - 470mm

Material:
Ramp - GF Tubing with Plastic Joiners
Foot Launch System - Ply with surgical rubber hose (2 metres)

WWII Allied Pilot (H68 x W72 x D43mm)

Specs:
Height: 68mm
Width: 72mm
Depth: 43mm
Weight: 31g

Alloy Oleo Set Twin Nosewheel/Stirrup Mains for 90mm EDF/1.20 Class 3pc - Superb looking and high quality Oleo leg's for Warbirds and scale models & Jet's, complete with axles, wheel spacers and steel mounting pins.

Specs:
Length to axle centreline Mains: 125mm (not inc pin)
Length to axle centreline Noseleg: 115mm (not inc pin)
Retract Mounting Pin: 5mm
Axle: 4mm
Maximum Wheel Diameter Main: 70mm (20mm Wide)
Weight: 138g

UltraDetail Scale Cockpit - Viperjet 90.

Specs:
Width: 105mm
Length: 353mm
Heigth: 70mm

These spoilers are a dream come true for those looking for an easy to install and set-up spoiler system for larger scale gliders.

They are single sided scissor action spoilers just like the full scale versions.
These fit flush to the wings surface when closed and proportionally open to their fully deployed height.

The working 'blade' length is 255mm and stands 20mm above the wing skin fully deployed.

Features:
• Alloy Construction
• Scale Scissor action
• Plug and Play electronics
• Open and Close limit switches

Spec:
Voltage: 5-6v
Overall length: 300mm
Installation Depth: 10mm
Height Deployed: 20mm
Plug: JR Style
Weight: 40g each

Note: This is a kit consists of 1 x left and 1 X right spoiler.

Spring loaded canopy lock.
Great for canopy, battery compartment or hatch.
Locking shaft protrudes 12mm
Lock mounting area: 15x26mm

Heli Ball Joints (without balls) (6pcs/bag)

Size:Linkage(long)2.0mm

Fighter Pilot

Specs
Height: 70mm
Width: 70mm
Depth: 39mm
Weight: 26g

UltraDetail Scale Cockpit perfect for many scale glider applications!

Specs:
Width: 76mm
Length: 270mm
Heigth: 130mm

The Turnigy Electrical Switch is a rugged solid state switch that has no contacts to fail like traditional mechanical switches. It can work on 4~8 NiMh/NiCD cells or a 2S 7.4V Lipoly battery. It features a Lipo mode which offers low voltage protection to the battery should the pack dip below 6.0V. A LED voltage indicator gives you at a glance status of your receiver so you always know how much of your pack is left. The plastic case has two tabs molded in allow you to mount it easily to your airframe for nice clean installations.

Features:
• Momentary on/off switch
• Screw mounting tabs
• Connectors work with JR/Futaba type servo plugs
• LED voltage indicator
• Lipo mode has voltage cutoff to protect lipoly batteries from over-discharge

Specs:
Input Voltage: 4.8~10V (2S Lipoly, or 4~8 cell NiMh/NiCD)
Continuous Current: 8A
Max Burst Current: 14A (10 sec)
Size: 43x33x9mm
Weight: 9g
Connectors: Futaba (Works with JR)

Add a touch of professionalism to your scale RC Jet with the "OK Hand
Style" Jet pilot. Suitable for 90mm Class Jets.

Specs:
Height: 91mm
Width: 77mm
Depth: 45mm / 64mm (Incl. Hand)
Weight: 34g

Add a touch of professionalism to your scale RC Jet with the "OK Hand
Style" Jet pilot. Suitable for 90mm Class Jets.

Specs
Height: 91mm
Width: 77mm
Depth: 45mm / 64mm (Incl. Hand)
Weight: 34g

This small lightweight 4ch switch is extremely handy for auxillary functions on all sorts of models. Plug the single lead into an auxillary switched function then switch your radio on, channel 1 on the electronic switch will then be active, cycle the auxillary switch once and channel 1 goes out and channel 2 comes on, cycle the switch once more and 2 goes out and channel 3 comes and so on until it comes back to channel 1. When the radio is switched off and then switched back on the unit will default to channel 1 each time. This unit is great for switching lights on and off and other low current applications.

Please note: For this switch to work correctly you will need to set the related channel travel to +- 100%.

Specs:
Input Voltage: 4.8~7.4v
Output Voltage: 4.8~7.4v
Maximum Current: 2amps
Length: 40mm
Width: 20mm
Height: 12mm
Weight: 7g
Input Cable: 21cm (JR type plug)

Specs:
Maximum throughput : 10A / 30v
Weight: 7g

These rare earth magnets are extremely powerful for their size and are manufactured using Neodymium, Iron and Boron. They are amongst the strongest permanent magnets commercially available and are now used in a variety of applications. These magnets are coated with 3 layers of nickel, copper, nickel to reduce corrosion and provide a smooth finish.

These small 10 x 10 x 2mm flat plate magnets have an incredible holding power for their size of 1.18kg (2.6lbs) when in flush contact with a steel plate which makes them the ideal choice where you require something that really needs to stay put. Each magnet has north and south poles on opposing faces.

Specs:
Type: Neodymium rare earth permanent magnet
Dimensions: 10 x 10 x 2mm
Holding Power: 1.18kg (2.6lbs)
Quantity: 10 pieces.

WARNING: DO NOT COMBINE THESE MAGNETS IN ORDERS WITH ELECTRICAL EQUIPMENT.

These rare earth magnets are extremely powerful for their size and are manufactured using Neodymium, Iron and Boron. They are amongst the strongest permanent magnets commercially available and are now used in a variety of applications. These magnets are coated with 3 layers of nickel, copper, nickel to reduce corrosion and provide a smooth finish.

These tiny 5 x 5 x 2mm flat plate magnets have an incredible holding power for their size of .46kg (1.02lbs) when in flush contact with a steel plate which makes them the ideal choice where you require something that really needs to stay put. Each magnet has north and south poles on opposing faces.

Specs:
Type: Neodymium rare earth permanent magnet
Dimensions: 5 x 5 x 2mm
Holding Power: .46kg (1.02lbs)
Quantity: 10 pieces.

WARNING: DO NOT COMBINE THESE MAGNETS IN ORDERS WITH ELECTRICAL EQUIPMENT.

These rare earth magnets are extremely powerful for their size and are manufactured using Neodymium, Iron and Boron. They are amongst the strongest permanent magnets commercially available and are now used in a variety of applications. These magnets are coated with 3 layers of nickel, copper, nickel to reduce corrosion and provide a smooth finish.

These small 20 x 10 x 2mm flat plate magnets have an incredible holding power for their size of 1.9kg (4.2lbs) when in flush contact with a steel plate which makes them the ideal choice where you require something that really needs to stay put. Each magnet has north and south poles on opposing faces.

Specs:
Type: Neodymium rare earth permanent magnet
Dimensions: 20 x 10 x 2mm
Holding Power: 1.9kg (4.2lbs)
Quantity: 10 pieces.

WARNING: DO NOT COMBINE THESE MAGNETS IN ORDERS WITH ELECTRICAL EQUIPMENT.

These rare earth magnets are extremely powerful for their size and are manufactured using Neodymium, Iron and Boron. They are amongst the strongest permanent magnets commercially available and are now used in a variety of applications. These magnets are coated with 3 layers of nickel, copper, nickel to reduce corrosion and provide a smooth finish.

These tiny 5 x 2 x 2mm rectangular magnets have an incredible holding power for their size of 0.24kg (0.53lbs) when in flush contact with a steel plate which makes them the ideal choice where you require something that really needs to stay put. Each magnet has north and south poles on opposing faces.

Specs:
Type: Neodymium rare earth permanent magnet
Dimensions: 5 x 2 x 2mm
Holding Power: 0.24kg (0.53lbs)
Quantity: 10 pieces.

WARNING: DO NOT COMBINE THESE MAGNETS IN ORDERS WITH ELECTRICAL EQUIPMENT.

Lt Col Bird - Promoted to the 90mm Jet Class, our favourite jet pilot is as gung-ho as ever making him the perfect choice for your new jet!

These handy wicks are great for lighting the smoke cartridges, each one will burn continously for 30mins.