Workbench

Looking for the professional finish on your next quadcopter project? look no further! This simple and easy to install light module set, will not only provide you with a proffesional look but will also allow your quadcopter to be seen in any conditions with its super bright LEDs

The LED flash light set offers a wide voltage input range from 2-6s and is suitable for quadcopters up to 500mm diameter. 

Features:
• Suitable for quadcopters up to 500mm diameter
• Wide input voltage, 2-6s capability
• High efficiency frequency conversion circuit
• Low power consumption
• No flashing delay or brightness reduction
• High power output
• Simple frequency adjustment

Specs:
LED Cable Length: 500mm
System Weight: 48g
Input Voltage 7.4v ~ 22.2v

Protect your multirotor ESC / battery connectors from impact or prop damage with these handy
PCB's. Simply solder your Male XT90 connector directly to the board and secure to your multirotor
frame with some 3mm nuts and bolts.

Specs:
Length: 35mm
Width 10mm
Depth: 1.5mm
Hole Spacing: 35mm max

Add additional realism to your scale model with this LED set which operates in conjunction with the MrRC Sound V4.1 Sound unit.

A set of 6 bright orange 5mm LED lights that is pre-wired for plug in use on the V4 and V4.1 and card. Simply plug them in, and the light flashes in sync with the gun sound on the Aux. 1 channel. (labeled servo 2 on the board)

Mount these in the machine guns of your favorite model to increase the scale realism.

For use with MrRC Sound V4.1 Speakerless Sound System found here.

This is the WWI sound pack chip for the V4 MrRCsound sound unit. It includes 6 common engine sounds used in a number of WWI era Allied and Axis planes. These are high quality digital recordings of the real things. Sounds: Fokker D VII, Real Gnome, Le Rhone, Easy Gnome, Tiger Moth, and Stearman Plus aux. sounds for each.

For use with MrRC Sound V4.1 Speakerless Sound System found here.

This is the WWII sound pack chip for the V4 MrRCsound sound unit. It includes 6 common engine sounds used in a number of WWII era Allied and Axis planes. These are high quality digital recordings of the real things. Sounds: Allison, BMW 801, Sakae (Zero), Mikulin AM-38 (IL-2/Mig-3), Bristol Centaurus (Hawker Sea fury), and Wright Cyclone. Plus aux. sounds for each.

For use with MrRC Sound V4.1 Speakerless Sound System found here.

Control Horns 16x20mm (10pcs)

Nylon & Pinned Hinge 20x36 (10pcs)

68mm Alloy Wheel/Rubber Tyre - Split Alloy Wheel with Grooved, foam cored Rubber Tyre, suits 4mm Axle.

Weight: 41g

M2.5 x 40mm Steel Push Rod (10pc)

Volantex 759-8 Phoenix 2000 - Propeller Blades.

Specs:
Diameter: 10 in.
Pitch: 6 in.

Volantex Phoenix 2000 - Propeller Set.

Set includes propeller blades, spinner, and collet prop adapter.

Specs:
Diameter: 10 in.
Pitch: 6 in.

Nylon Arm 2.8 x 6 x 6 (10pcs)
Diam: 2.8mm

Front Wheel Steering Arm & Mount Set (5sets)

29x26x13.5mm
diam4x40

Adjustable Control Horn 3x24mm (5sets)

Pivot & Round Hinges 2x33 (10pcs)

Hatch 30x16mm (5pcs)

CA Hinge L25*W20*H0.3 (10pcs)

Micro Control Rod Rocker Horn (7mm x 3mm - 10pcs)

Turnigy Scale Jet Alloy Wheel w/Rubber Tire (45mm) - Superbly made alloy wheel with a high quality, hard wearing scale rubber tire.

Specs:
Diameter: 45mm (tire diameter)
Width: 8mm (tire width)
Axle: 3mm
Weight: 17g

This is a very handy little device that is used to sequence the landing gear doors and landing gear both during extension and retraction.

With the use of spitter leads you are able to sequence an entire gear and door system on many models that require correct sequencing from just one of these units and from a single channel on your reciever.

There are two selectable sequence types and there is an instruction leaflet included.

Specs:
Dimensions: 52x18x5mm
Voltage range: 4.8-6.0v
Weight: 5.5g

*Color may vary

Turnigy Electric Magnetic Brake System - Replacement Controller

Spec Controller:
Operating Voltage: 12v~40v (3s~10s)
Output Voltage: 2A/0v~12v
Dimensions: 55mm x 7mm x 26mm
Weight: 15g

Lt Col Bird - Promoted to the 90mm Jet Class, our favourite jet pilot is as gung-ho as ever making him the perfect choice for your new jet!

Nylon Clevis 2x29 (10pcs)

30mm Aluminum spinner prop nut 3/8"-24

Prop Nut/Spinner 22mm Alloy 5/16"-24

Prop Nut/Spinner 22mm Alloy 3/8"-24

Prop Nut/Spinner 22mm Alloy M10x1.00 Anodised Black

Prop Nut/Spinner 22mm Alloy M7x1.00 Anodised Red

22mm Alloy Prop Nut/Spinner Suites 10mm Thread (Anodised Red)

Height:20mm
Width:22mm
Thread Size:10mm
Thread Depth:20mm

Hex spinner prop nut Alloy M7x1.0

Hex spinner prop nut Alloy M8x1.0

Hex spinner prop nut Alloy M10x1.00

Hex spinner prop nut Alloy 5/16"-24

Brass Nut for Spinners M8x1.25-M4

Pull-pull/3mm Clevise Quick Link Couplers - 26mm Length