Workbench

The Hole Tapping Jig Set has been specifically designed for use with the RotorBits square 10mm tube. The jig slides neatly onto the square tube and can be secured with 4 locking screws (included) which will prevent the jig slipping once located in the preferred position.

The hole tapping jig set also includes a hole reamer, 2mm drill bit and 2mm thread tap.

Specs:
Jig Material: Steel
Jig Weight: 154g
Jig Dimensions: 100 x 16 x 20mm
Supplied Tools: Hole reamer, 2mm drill bit, 2mm thread tap

R/C Helicopter Pitch Gauge, a must for when setting up your RC helicopter.

Specs:
Range: +12°, -12°
Material: Plastic
Suits: Most mini-helicopters

A lightweight, highly adaptable model aircraft stand, ideal for building, field assembly and storage of all but the largest of models (We've used these for models up to 2m long without any problems.)

The interlocking, all foam stand assembles in seconds, is flexible, strong and will not leave marks on your model.

Specs:
Length: 580mm
Width: 300mm
Height: 355mm
Weight: 530g

Tired of wrestling with two pairs of pliers or using a vise to help you try and obtain that perfect Z-bend for your control rods, only to end up with a half formed S shaped bend with too much middle in it for a Z bend allowing your control surfaces to slop around? Sound like some of the Zs you have made?
These pliers will give you a perfect bend, every time. It will handle toughened wire up to 1/16 (1.6mm) diameter.
These are heavy duty pliers, not small hobby workshop tools.

Get your Z-bends easy and perfect every time with the Z-Bend Pliers!

The HobbyKing helicopter pitch gauge is made from ultra-rigid fiberglass board and features dual ball bearings to ensure accurate measurements every time. This pitch gauge is supplied in kit form to keep production costs down which means we can pass the savings on to you!

Specs:
Measurement: +/- 20 Deg
Size: 145mm x 105mm
Max Blade Width: 80mm

Note: An assembly guide can be found in the FILES tab below.

Cut in style with your very own HobbyKing Cutting mat.
Perfect for protecting your work surface and keeping your hobby knife sharp.

Size: L450mm × W300mm (18"x12")

This extendable magnetic pick-up tool is a great addition to any toolbox, it makes picking up small metal parts that fall in hard to reach places extremely easy.

Specs:
Magnet Diameter: 7mm
Extended Length: 635mm
Magnet Strength: 1.5kg lift capacity

These replacement drivers have been specifically designed to fit the Turnigy high quality drivers and drive sets (rubber handled type). The replacement shafts are manufactured from high tensile steel and are hard coated to prevent corrosion.

Specs:
Drive Type: Flat head screwdriver
Tip Size: 5mm
Shaft Diameter: 5mm
Shaft Length: 120mm
Weight: 17.06g

Handy large brush with coarse nylon bristles and wooden handle suitable for painting or cleaning.

Specs:
Diameter: 27mm
Length: 280mm
Bristles: Coarse nylon
Handle: Wood

The Turnigy V2 range of drivers: comfortable, high quality, precision tools at a price that can't be beaten.

The Turnigy V2 range of drivers: comfortable, high quality, precision tools at a price that can't be beaten.

The Turnigy V2 range of drivers: comfortable, high quality, precision tools at a price that can't be beaten.

Replacement 1.5mm Hex drive tip for Turnigy V2 series drivers.  The shafts are manufactured from spring steel to provide superior durability and a tight clean fit in the screw head. 

Replacement 2.5mm Hex drive tip for Turnigy V2 series drivers.  The shafts are manufactured from spring steel to provide superior durability and a tight clean fit in the screw head. 

Replacement 2.5mm Arm Reamer Tip for Turnigy V2 series drivers.  The shafts are manufactured from spring steel to provide superior durability and a tight clean fit in the screw head. 

Replacement 3.0mm Arm Reamer Tip for Turnigy V2 series drivers.  The shafts are manufactured from spring steel to provide superior durability and a tight clean fit in the screw head. 

Replacement 4.0mm Arm Reamer Tip for Turnigy V2 series drivers.  The shafts are manufactured from spring steel to provide superior durability and a tight clean fit in the screw head. 

The Turnigy V2 range of drivers: comfortable, high quality, precision tools at a price that can't be beaten.

The Turnigy V2 range of drivers: comfortable, high quality, precision tools at a price that can't be beaten.

The MultiStar Work Mat is a must have for any R/C hobbyist's work bench! Made from soft, grippy rubber and featuring ribbed compartments, it is perfect for containing small parts such as screws, nuts, washers and more. The backing is very grippy which will keep it from slipping on just about any surface. 

These smaller mats make excellent launch pads if you are taking off from uneven surfaces like grass or gravel.

The material is very soft and flexible allowing it to be easily rolled up for transport or storage. This makes it very easy to take with you to the race or field for on-site repairs. Never lose a screw again with the MultiStar Work Mat!

Features:
• Soft, grippy surface
• Ribbed compartments for containing small parts
• Flexible, can be rolled up for transport/storage

Specs:
Dimensions: 395 x 250mm

Have you ever struggled to see into confined or inaccessible voids to locate a lost item or just to see what's going on in there?

With an almost endless list of applications from drainage inspection to wiring conduits, motor vehicles to underwater fish tank photography, this mini endoscope is incredibly simple to use as it plugs directly into your Android device or PC to be ready to take video or stills and store them at a moment's notice.

The 7mm diameter camera head is equipped with its own adjustable lighting thanks to the 6 built in LED lamps and, being dust and waterproof (IP67 standard) can be used underwater or in dusty conditions.

IP67 standard rates this item as totally protected against dust and protected against the effect of immersion between 150 and 1000mm

The set is completed by the inclusion of a micro/standard USB adapter, spring and magnetic mounting clips.

To use the endoscope with your mobile phone or tablet you'll need to download the CameraFi application from the Google Play Store so that your Android device can recognise the remote camera.

Features:
• Simple to use
• Highly portable
• Compatible with Android and Windows
• Water/dust proof to IP67 standard
• Built in LED lighting
• 2m Cable supplied

Specs:
Cable length: 2m
Camera head dia: 7mm
Lighting: 6 LED light (with Brightness control)
Android resolution: 640 x 480
PC resolution: 1280 x 720
Frame rate: 30fps
Focal distance: 40mm ~ infinity
Viewing angle: 66°
Supported OS: Android/Windows 2000/XP/Vista/7

Package Included:
1 x USB Endoscope
1 x Spring clip
1 x Magnetic clip
1 x USB Connector adapter

Note:
Does not support IOS system.
Android Phone must support OTG function, and must support to connect external camera.

Supported phones:
Samsung Galaxy S3(i9300, i9308), S4(i9500, i9508), S5, S6, S6 Edge, S7, S7 Edge; Note2, Note3, Note4 Note 5, P600 Tablet, N5100 Tablet; SONY Z2 L50H; SONY LT26i, Z1, Z2, Z3, Z5, C3; Nexus 5; LG Gpro2, L24, Gpad 8.3; Moto Xpro, Nexus6, Moto E, MZ17; HTC 9088, Nexus 9, M7, M8, M9; HUAWEI G7, MATE8, P9.

Turnigy 1/2" Hex Socket Screwdriver
Ultra strong steel tip, wont break or round like other cheap drivers.
Lightweight, hollow alloy handle means it wont weigh down your R/C gear case.

Turnigy 3/8" Hex Socket Screwdriver
Ultra strong steel tip, wont break or round like other cheap drivers.
Lightweight, hollow alloy handle means it wont weigh down your R/C gear case.

Static Control Crank Handle Brushes are ideal for cleaning electronic components and prevent static build up that can potentially damage the components.

Specs:
Surface Resistance: 10⁴-10⁶ Ohm
Bristle Dimensions: 60 x 20mm
Handle Dimensions: 170 x 10mm 

Tamiya Mini bending Pliers are perfect for small photo-etched parts which have no identifiable bending lines. The easy grip handle provides comfortable use whilst maintaining maximum control. The pliers allow you to bend straight lines up to 20mm.

Specs:
Nose Length: 20mm
Overall Length: 130mm
Weight: 49.13g 

Tamiya premium quality, clog free, wet and dry sanding paper. Ideal for modelers looking for the perfect finish. The pack contains 2 x P180, 1 x P240, 2 x P320. 

Specs:
Grades: P180, P240, P320
Dimensions: 229 x 93mm
Quantity: 5 pcs

Tamiya Standard Flat Brushes are made from horse hair and feature lightweight hardwood handles. Ideal for painting larger surface areas of models.

Specs:
Bristle Material: Horse hair
Bristle Length: 20mm
Handle Material: Hardwood
Weight: 4.41g
Dimensions: 220 x 7mm

Tamiya Standard Flat Brushes are made from horse hair and feature lightweight hardwood handles. Ideal for painting larger surface areas of models.

Specs:
Bristle Material: Horse hair
Bristle Length: 11mm
Handle Material: Hardwood
Weight: 2.86g
Dimensions: 220 x 5mm

Tamiya Standard Flat Brushes are made from horse hair and feature lightweight hardwood handles. Ideal for painting larger surface areas of models.

Specs:
Bristle Material: Horse hair
Bristle Length: 7mm
Handle Material: Hardwood
Weight: 1.4g
Dimensions: 210 x 4mm