Power Systems

The motor is a powerful, high torque open brush gear 540 motor, brushes can be changed when they wear out and this is matched to a 60amp ESC. The Trackstar Crawler ESC has been specifically designed for RC crawlers and brushed motors. It gives an excellent linear response and driving feel, has a low internal resistance, excellent heat dissipation, and multiple protection features (see features below). It can be easily programmed with the optional pocket-sized LED program card (see related items) with a variety of different settings including; Initial Start Force, Low Voltage Cut-Off, Initial Drag Brake Force, Maximum Reverse Force, and 3 Start Modes.

The motor is a powerful, high torque open brush gear 540 motor, brushes can be changed when they wear out and this is matched to a 60amp ESC. The Trackstar Crawler ESC has been specifically designed for RC crawlers and brushed motors. It gives an excellent linear response and driving feel, has a low internal resistance, excellent heat dissipation, and multiple protection features (see features below). It can be easily programmed with the optional pocket-sized LED program card (see related items) with a variety of different settings including; Initial Start Force, Low Voltage Cut-Off, Initial Drag Brake Force, Maximum Reverse Force, and 3 Start Modes.

The motor is a powerful, high torque open brush gear 540 motor, brushes can be changed when they wear out and this is matched to a 60amp ESC. The Trackstar Crawler ESC has been specifically designed for RC crawlers and brushed motors. It gives an excellent linear response and driving feel, has low internal resistance, excellent heat dissipation and multiple protection features (see features below). It can be easily programmed with the optional pocket sized LED program card (see related items) with a variety of different settings including; Initial Start Force, Low Voltage Cut-Off, Initial Drag Brake Force, Maximum Reverse Force and 3 Start Modes.

An excellent open carbon brush gear 540 35T motor that has been designed for, and is perfect for RC crawlers. Having the brush gear open means that maintenance, cleaning, and brush changing is a very simple task. The low 1320KV means masses of low down torque which makes it ideal for climbing steep and rough terrain at controllable low speeds.

PROPDRIVE v2 motors are designed to perform right out of the box with tight windings, smooth bearings, correctly rated magnets, precision cut stator, and balanced rotors.

We design and build the PROPDRIVE v2 motors in-house, allowing us to control every aspect of production. We control the entire production line from material sourcing to machining, balancing, and final assembly. PROPDRIVE motors can be trusted to provide years of reliable service at a price every modeler can afford.

Performance Data (5S):
15x6: 796W, 45A, 3338g static thrust
15x8: 970W, 56A, 4151g static thrust
16x7: 1053W, 60A, 4259g static thrust

Performance Data (6S):
13x6.5: 896W, 42A, 3567g static thrust
13x8: 1042W, 50A, 4214g static thrust
14x7: 1170W, 56A, 4439g static thrust

FrSky TFR6 7ch 2.4Ghz Receiver FASST Compatible

Compatibility:
FASST 2.4G: Air Systems (7CH Mode/Multi Mode)
FrSky TF Modules: TF-8M, TF-14M


Features:
Light weight and small size
Two selectable failsafe setting options


Specifications:
Number of Channels: 7
Operating Voltage Range: 3.5V~10V
Operating Temperature Range: -10C~60C
Dimension: 37*22*8mm
Weight: 7.8g

This is the USB link for programming your HobbyKing X-Car 120A & 60A brushless sensored/sensorless ESC. It will allow you to adjust all of the programming options quickly and easily via your PC.

Learn More

26mm Diameter Motor Mount - Clamp Style for Inrunner Motor

Spec.
Diameter: 26mm (Fits 380 Size Inrunner)
Length: 48.5mm
Weight: 14g

USBasp AVR Programming Device for ATMEL Processors

Includes:
1 x USBasp Device
1 x Cable

Suits the HobbyKing Quadcopter Control Board.

Replacement Rear Crankshaft Bearing for NGH GT35 and GT35R Gas Engines.

NGH GT17/GF38 Gas Engines Replacement Crankshaft Rear Bearing

Specs:
Outlet Diameter: 35mm
Inner Diameter: 17mm
Width: 8mm

NGH GT25/GF38 Gas Engines Replacement Crankshaft Front Bearing

Specs:
Outlet Diameter: 26mm
Inner Diameter: 10mm
Width: 8mm
Type: Sealed

A high thrust and well designed Electric Ducted Fan unit for high power applications, the 10 blade arrangement makes for a quiet fan unit with an amazing sound, this is the closest you will ever get to the sound of a Turbine!

Made with 30% FRP and dynamically balanced, for use with high performance 28mm EDF motors, either 3.17m or 4mm shaft. For the best results from this fan, we reccomend the Turnigy 2855 EDF motors.

Specs:
Outside Diameter: 72mm
Rotor Diameter: 68mm  blade
Meterial: carbon fiber reinforced Nylon rotor 
Shaft adaptor to motor: 3.17mm or 4mm
Max RPM: 45000 RPM

Aluminum alloy neck strap adjuster suitable for DJI transmitters or similar.

TURNIGY Programming Card

For use with Turnigy Plush ESCs (exc Plush-32)

This device plugs inbetween the Rx and the speed controller. It allows the user to program the BESC according to a series of LED indicators.
it has buttons at the bottom so you can navigate through the menu and select the feature you want, then change it. Its very simple and is much easier than listening to jingles or a series of beeps.

This item is an excellent addition to your flight kit, especially with the new hard plastic case and lets you quickly change the BESCs settings in the field in a much shorter time and with greater assurance that what you have changed is correct and saved into the BESC.

No more black magic throttle stick programming!
Throw away the manual, you wont need it anymore!

Compatible with Turnigy Plush speed controllers but NOT the Plush-32 ESC's.

Combined with a 10x6 E-prop this motor can push out over 1000g in thrust on a 3S1P configuration lipo.
Good for bigger foamies or parkflyers where about 150W is required.

Spec.
Kv: 1050rpm/v
Operating Current: 6A ~ 16A
Peak Current: 19A
Weight: 56g
Dimensions: 27.6 x 32mm
Shaft Size: 3.175mm

Kit includes full accessories, including gold bullet connectors, prop saver, mount, spare rubber rings, shrink tube and screws.

Performance Data   
Voltage   Current   Prop    Thrust
11.1V      8.6A      8040    538g
11.1V      13.7A    9050    810g
11.1V      16.7A    1060    650g

Futaba Trainer Cable (Buddy Box Cable) 2.8m

The Turnigy Voltage Protector helps prevent your receiver from dropping below its required operating voltage. This helps to eliminate "brownouts" and prevents your receiver from rebooting. It will also help reduce the load on your ESC's BEC and reduce the likelihood of glitching. Simply plug it into any spare channel on your receiver.

Operating Voltage : 3.2V - 11.1V (1s ~ 3s LiPo)
Capacitor voltage: 16v
Storage Capacity: 3300uf
Weight: 6.1g

Turnigy TY-P1 25Amp Brushless ESC Programming Card

Programming Options:
Brake (OFF/ON).
Cut-off Type (Soft-cut/Cut-off).
Cut-off Voltage (Low / Middle / High ).
Start Mode (Normal / Soft / Very Soft ).
Timing Mode (Low / Middle / High).
Cell (Auto, 2S, 3s, 4S).

This set can be used with your own compatible transmitter as a replacement for a lost or damaged USB simulator cable. Includes adapters for Esky, JR/Spektrum and Futaba.

Compatible with XTR, AeroFly and FMS
Includes driver software.

High quality servo wire for making your own custom length servo leads.

Specs:
Wire Diameter: 26AWG each wire
Length: 5mtr
Color: Red/Black/White

Turnigy Aerodrive SK3 3536 Series Replacement Shaft Set

Spec.
Shaft length: 58mm
Shaft diameter: 5mm

Turnigy Aerodrive SK3 6354 Series Replacement Ball Bearing Set (3pcs/bag)

Spec.
1x 19mm x 8mm x 6mm
2x 12mm x 8mm x 3.5mm

Propeller adapter for BE1806 motor 2 x CW

The FrSky S.BUS to PWM Decoder allows you to use any standard analog or digital servos with your S.BUS compatible receiver. This eliminates the need for using pricey S.BUS specific servos allowing you to use your models existing servos.

Featuring 4 programmable channel outputs, you can independently assign each servo to a channel of your choice while only having to connect one input lead from your receiver. This makes your wiring much more tidy and allows for easy setting up of your servos without the need for running multiple extension leads.

This is a great device to use in conjunction with our Orange 7CH and 9CH S.BUS compatible receivers!

Includes:
FrSky S.BUS to PWM Decoder

Specs:
Channel Outputs: 4 programmable
Channel Ouput Lead Lengths: 200mm
Overall Length: 350mm

*Note: FrSky Servo Channel Changer required (sold separately, see related items below) to change assignment of channel outputs.

The FrSKY S.Port to UART Converter supports a link with external analog devices via two ADC ports for Serial port Data-Transmission at S.Port BUS and analog signal AD input via S.Port.

The pack contains module A and B along with 2 x male to male jumper cables.

Specs:
Mode: SP2UART
Operating Voltage: DC 4 -10 V
Weight: 3g
Size: 44 x 15 X 7mm
Current Draw: 20mA @5V
Operating Temperature Range: -40 ~ 85 Degrees C

Turnigy Air Brushless Motor 3730-1000kv
 
Specifications:
Dimension: 37mm x 30mm
Weight: 112g Inc 4mm Gold Connector (130g inc all fittings)
Kv: 1000rpm/V
Voltage: 11.1v~14.8v (3s~4s)
Max Power: 580w
Max Current: 42A
No load Current: 1.6A
Diameter of shaft: 4mm
Thrust: 1700g
ESC: 60A

Specs.
RPM/V: 1350Kv
Cell Count: 2s~3s Lipoly  
Max.current: 10A
Max Watts: 120w 
No Load Current: 0.3A/7.4V 
Dimensions: Φ28mm×16mm
Shaft: 3mm
Weight: 26g
Max Thrust: 245g

A powerful, lightweight micro brushless motor that is ideal for those small indoor or even parkfly type models. Nicely machined and balanced, hand wound with thick gauge copper, supplied with X mount, mounting screws, 2mm connectors and prop driver.

Specs:
Model: LD1510A-02-P
Kv: 2200rpm/v
Weight: 16.5g (with wires and mount)
Voltage: 7.4~11.1V
No Load Current: 0.2A
Max Current: 6A
Max Power: 60 watts
Shaft Diameter: 2mm
Motor Diameter: 18mm
Mount Bolt Hole Centers: 25mm
Mounting Bolt Size: 2mm
Connector: 2mm
Suggested ESC: 10A

LDPOWER MT2206-1900KV Brushless Multicopter Motor (CW)

Innovators in multicopter technology, LDPOWER, have released their long awaited series of premium multicopter motors. These have been stringently tested to ensure outstanding performance, reliability and durability.

These motors are easy to install, very efficient and have no noise. They come in both CW and CCW formats.

LDPOWER motors are premium quality and will definitely answer the need of serious builders and flyers of quads/multis everywhere.

Specs:
KV(RPM/V): 1900KV
LiPoly cells: 7.4V-11.1V (2S-3S)
Max Power: 323.8W
Max Amps: 25.7A
Dimensions(Dia.xL): 29.5 x 27.7mm
Motor Shaft: 3mm
Prop shaft: 5mm
Weight: 34.7g
Bolt hole spacing: 19mm-M3*2  16mm-M3*2
Connectors: 2mm bullet

Volts  Prop   Throttle  Amps  Watts     RPM     Thrust (g)
7.4    6030   30%     1.8      13.32      8792      85
7.4    6030   50%     2.7      19.98    10341     123
7.4    6030   75%     3.9      28.86    11949     171
7.4    6030   100%    5.3      39.22    13656     228
7.4    6045   30%     2.5      18.5        7107     115.5
7.4    6045   50%     3.7      27.38     8607      164.5
7.4    6045   75%     6.0      44.4     10216      240
7.4    6045   100%    9.2     68.08    12003      335
11.1   6030   30%     3.1     34.41    12140      180
11.1   6030   50%     4.6     51.06    15621      249
11.1   6030   75%     6.9     76.59    16420      350
11.1   6030   100%    10.3   114.33   18953      480
11.1   6045   30%     3.8      42.18     9592      210
11.1   6045   50%     5.8      64.38   11258      292.5
11.1   6045   75%     10.1    112.11  13817      430.5
11.1   6045   100%    16.2    179.82  16315      594.5