Power Systems

Rx700NR is a small and very light weight receiver with 9 channels that has a range of up to 20km! It also has an optimized input filter which will prevent interference from strong 2.4 GHz video systems.

The Rx700NR will work with any Scherrer long range transmitter and will provide you with a solid and safe signal for your flights. The antenna is mounted directly on the board and with a total weight of only 8 grams this receiver is perfect for UAVs where the focus is on weight and longer flight times.

Features:
• Up to 20km range
• External firmware upgrade port
• Running LED
• Completely new software
• Selectable PPM/PWM
• Sequential failsafe

Specs:
Board Dimensions: 26 x 53mm
Weight: 8g
Number of channels: 9
Output: PPM output 
Rssi output: 0.5 to 3.3V from min to mix
Supply voltage: 4 -10 V
Supply current RX: 18mA at 5V
System: Wideband frequency hopping 
Band: 433 and 440 MHz 
User firmware upgradeable: Yes
Wide user temperature range: -40C to +70C ambient

The OrangeRx SF7003XS has all the properties and features of the original FASST compatible receivers in the OrangeRx brand but this one now operates on the later Futaba FHSS (Frequency Hopping Spread Spectrum) system. This receiver also has S-Bus and a built in 3 axis stabilizer which is brilliant in model airplanes to help beginners master the art of RC flying and for experienced pilots to make their flying even smoother. This receiver is perfect for the large gliders with long wingspans, it really helps to smooth out the turns and nose attitude when thermalling at higher altitudes.

The stabilizer function has 5 modes, mixer off, dual ailerons, V-tail mixing, delta mix and dual aileron/V-tail mixer. There are independent, simple to use gyro gain adjustments for the aileron, elevator and rudder functions, the stabilizer function can also be switched on and off in flight via CH5. The S.Bus functionality is perfect for large models and gliders that utilize a lot of servos, especially in the wings, it reduces the amount of wiring and keeps things nice and tidy.

The receiver will also accept a wide range of input voltages from 3.6~8.5V which is great if you want to use LV and HV type servos.

Compatible with the following Futaba FHSS 2.4Ghz air systems: 4YF, 6J, 8J and 10J, can also be used with the T14SG under S-FHSS protocol mode

Features:
• Lightweight (16g)
• Compatible with FHSS 2.4Ghz air systems
• 7 channels
• Built in 3 axis stabilizer
• 5 stabilizer modes
• Supports SBus
• Compact design (54 x 32 x 13mm)
• Failsafe and battery failsafe
• Extremely low latency
• Fast frame rates
• Hops from frequency to frequency in a pseudorandom sequence
• Advanced algorithms create a secure frequency

Specs:
Type: SF7003XS
Input Voltage: 3.6~8.5V
Operating Current: 60mA max
Battery Failsafe Voltage: 3.8V
Latency: 6.8mS
Sensitivity: About -96dBm
Dimensions: 54 x 32 x 13mm
Weight: 16g

Included:
OrangeRx SF7003XS receiver
Plastic screwdriver for making adjustments
Instruction manual

Note:
All OrangeRx receivers come with a 12 month warranty. This is not a Futaba receiver, nor is it a copy of a Futaba receiver. Futaba, FASST and FHSS are trademarks of Futaba Co (JP).

The Orange R8DM is a 2.4GHz DMSS compatible receiver that is designed for use with JR DMSS 2.4GHz transmitters, such as XG6,XG7,XG8 ,XG11 and XG14 under DMSS protocol mode.

Affordable and with a great reputation for reliability, Orange receivers are a fantastic alternative for budget conscious hobbyists and this 8 channel receiver for JR 2.4Ghz transmitters is just outstanding value. 

Features:
• Full Range Receiver
• 8 Channels - Throttle, Aileron, Rudder, Elevator, Gear, Aux1, Aux2, SBAux3. 
• SBUS support on channel 8 (Aux3)
• For use with JR DMSS transmitters
• Light weight
• Fail Safe Programable

Specs:
Model: RG831B 
Type: Full range receiver 
Channels: 8 
Modulation: DMSS 
Band: 2.4GHz 
Weight: 11g
Voltage Range: 3.6V~8.5V 

Turnigy AX-2203C 1400KV/60W Brushless Outrunner Motor

A high-quality compact and lightweight brushless outrunner motor for indoor and park fly type models. This motor is supplied with an integrated prop driver (O ring not supplied), suitable for planes weighing up to 275g.
(No connectors supplied)

Performance Data (2S):
8x4: 31W, 4.4A, 218g static thrust
8x6: 37W, 5.2A, 260g static thrust
9x6: 43W, 6.1A, 273g static thrust

A high quality compact and lightweight brushless outrunner motor for indoor and parkfly type models. This motor is supplied with an intergrated prop driver (O ring not supplied), suitable for planes weighing up to 350g.

(No connectors supplied)

Performance Data (2S):
7x4: 31W, 4.3A, 234g static thrust
8x4: 41W, 5.8A, 279g static thrust
9x5: 56W, 8A, 343g static thrust

The Quanum QM12V5A-UBEC is an advanced switching regulator that will supply 5-8 amps of power for your servos and accessories. The UBEC has an input range of 7.2-25.2v (2-6 cell Lipo) and has a switchable voltage output (7.2V/12V). The UBEC also features an inline noise reduction filter and dual output connectivity, which allows you to power servos and additional accessories independently!

Features:
• 5A power output (8A Bursts)
• Switchable voltage output (7.2/12V)
• Dual output connectivity
• In-line noise reduction filter

Specs:
Output: 5A continuous, 8A burst rate
Input: 7.2v - 25.2v (2-6s Lipo)
Size: 55 x 28 x 10mm
Weight: 32.5g

* To enable 12V output, input voltage source need to be at least 12V.

Turnigy SK3 Motors are the next leap forward in motor quality and design. We instructed the engineers to source the best quality magnets, bearings and materials available to them and develop a motor that would not only rival, but surpass the quality of many leading motor manufactures on the market today.

The result is an efficient, high caliber motor using quality double shielded bearings, sintered Neodymium magnets and a string wound stator ensuring an accurate and consistent winding each and every time.

The Turnigy SK3 motors are suited to modelers who are seeking a quality brushless motor without compromise.

Specs.
Motor Type: 4 Pole Inrunner
Winding: 2.5D
Voltage: 5~6S Lipoly
RPM/V: 1900kv
Internal resistance: 0.011 Ohm
Max Loading: 80A
Max Power: 1770W
Shaft Dia: 5.0mm
Weight: 249g
Motor Plug: 3.5mm Bullet Connector
For 90mm EDF Units

This small lightweight 4ch switch is extremely handy for auxillary functions on all sorts of models. Plug the single lead into an auxillary switched function then switch your radio on, channel 1 on the electronic switch will then be active, cycle the auxillary switch once and channel 1 goes out and channel 2 comes on, cycle the switch once more and 2 goes out and channel 3 comes and so on until it comes back to channel 1. When the radio is switched off and then switched back on the unit will default to channel 1 each time. This unit is great for switching lights on and off and other low current applications.

Please note: For this switch to work correctly you will need to set the related channel travel to +- 100%.

Specs:
Input Voltage: 4.8~7.4v
Output Voltage: 4.8~7.4v
Maximum Current: 2amps
Length: 40mm
Width: 20mm
Height: 12mm
Weight: 7g
Input Cable: 21cm (JR type plug)

Specs:
Maximum throughput : 10A / 30v
Weight: 7g

Introducing our Dr. Mad Thrust high performance EDF series. The Dr. has been hard at work to bring you MAD power EDF systems with excellent quality and high performance at a price that will leave some cash in your pocket.

The Dr. Mad Thrust EDF series are pre-assembled and dynamically balanced making them easy to fit, with no unit assembly required. As well as high power, these fans have excellent cooling and run so smoothly, the sound is amazing. There is also no housing distortion unlike plastic fans. This high quality, powerful fan is a great way to turn your 40mm EDF jet into a speeding missile!

This 40mm, 8-blade combo with the inrunner motor was developed by Dr. Bret Becker, for his record breaking Electrolyte Micro EDF sport jet, and is capable of pushing the model past the 100mph barrier. That ARF model will be available soon from HobbyKing, but you can get his prescription for power early for all your micro EDF projects!

Dr. Mad Thrust EDF series - just the right prescription for your model!

Features:
• Pre-assembled
• Factory dynamically balanced
• High power with superior cooling
• High quality construction
• Fully serviceable
• Fast to fit
• No housing distortion

Specs:
Rotor size: 40mm, 8 Blades
Weight: 63g
MAX RPM: 96000
MAX Power (10sec.): 330 Watts
Continuous Power: 290 Watts
Motor size: B2225
Kv: 8000
Voltage: 11.1V
Current: 26A
Thrust Power Upto: 400g
Inner Dia: 41mm
Outer Dia: 43mm
Motor Connectors: 2mm Bullet

Receiver for the Turnigy TGY-i6 transmitter. This parkflyer sized receiver features dual antennas for optimal performance and no fear of interference.

Features:
• Reliable, interference free 2.4GHz AFHDS 2A signal operation
• Ultra light weight design
• Dual antennas for most reliable interference free operation

Turnigy iA6 Receiver Specs:
Channel: 6
Frequency: 2.4g ISM Frequency Range
Power: 4.5V~6.6V/<30ma
Net Weight: 6.4g
Dimensions: 40.4x21.1x7.35mm

The HobbyKing® ™ GT2E is a affordable, 2-channel 2.4ghz ground radio, with adjustable steering dual-rate and servo reversing, making it a very simple setup for your car or boat. The automatic frequency hopping digital system provides a strong, reliable 2.4ghz signal, so rest assured you'll always be in control. Included in the package is a 3-channel mini receiver that will fit in most vehicles. The ergonomic feel of the trasnsmitter will feel good in your hands even after long track sessions.

Features:
• Reliable, interference free 2.4GHz AFHDS signal operation
• 2CH operation
• Use only 4xAA batteries for transmitter
• Adjustable steering dual-rate
• Simple binding procedure

Transmitter Specs:
RF Power: 20dBm (100mW) max
Modulation: GFSK
System Type: AFHDS 2A
Sensitivity: 1024
Low Voltage Warning: Yes
DSC Port: 3.5mm
Charge Port: Yes (3.5IN)
Power: 4xAA, 6VDC
Weight: 241g

Receiver Specs:
RF Receiver Sensitivity: -105dBm
Modulation: GFSK
System Type: AFHDS 2A
Sensitivity: 1024
Failsafe: Yes (Channel 2)
Power Port: Yes (VCC)
Power: 4.5~6.5 VDC 
Weight: 5g
Antenna Length: 26mm
Dimensions: 37x22x12mm

Includes:
HK-GT2E transmitter
HK-GT2E 3CH receiver
Antenna tube
Bind plug
User manual

HobbyKing™ GT2E 2.4Ghz Receiver 3Ch

Model: Car/Boat
Channels: 3ch
Frequency band: 2.4Ghz
RF Receiver Sensitivity: -105dBm
Modulation: GFSK
System Type: AFHDS 2A
Sensitivity: 1024
Failsafe: Yes (Channel 2)
Power Port: Yes (VCC)
Power: 4.5~6.5 VDC 
Weight: 5g
Antenna Length: 26mm
Dimensions: 37x22x12mm

The Turnigy TGY-i6 is a great entry level 6-channel telemetry 2.4GHz computer transmitter that uses solid and reliable Automatic Frequency Hopping Digital System (AFHDS) spread spectrum technology. The Turnigy TGY-i6 has both a nice quality look and feel, while the programming is simple to use. The TGY-i6 also has an impressive list of features and includes a TGY-iA6 6-channel receiver. Suitable for both model Heli and Airplane, the Turnigy TGY-i6 is a superb budget computer radio for both new pilots and experienced pilots alike!

The Turnigy TGY-i6 is a great entry-level 6-channel telemetry 2.4ghz computer transmitter that uses solid and reliable Automatic Frequency Hopping Digital System (AFHDS) spread spectrum technology. The Turnigy TGY-i6 has both a nice quality look and feel, while the programming is simple to use. The TGY-i6 also has an impressive list of features and includes a TGY-iA6 6-channel receiver. Suitable for both model helicopters and airplanes, the Turnigy TGY-i6 is a superb budget computer radio for both new and experienced pilots!

Reliably monitor the voltage of your battery with the Turnigy TGY-CVT01 Voltage Sensor.

As a great alternative to setting a timer, fly or drive your model based on the actual voltage of your battery. This way if your voltage drops quicker than usual due to harder running, you can avoid over discharge your pack. Or, perhaps you're having a nice relaxed day? Enjoy longer run times and don't cut yourself short.

This small, compact sensor is also a perfect way to add piece of mind when running a high performance model by allowing you to check that the battery voltage isn't dropping excessively under load.

For use with the TGY- i10 and i6 transmitters and TGY-iA10 and i6 V2 receivers.

Designed to daisy chain together with other TGY-C series sensors.

Features:
• High quality, compact sensor
• Futaba style input and output connectors
• Great for monitoring battery voltage, no need to set timers anymore
• Works with TGY- i10 and i6 transmitters and TGY-iA10 and i6 V2 receivers

Specs:
Voltage Range: 0~100V DC
Accuracy: +/- 0.1V
Input Voltage: 4.0~6.5V
Working Current: 9mA
Lead length: 195mm
Size: 31 x 15 x 8.5mm
Weight: 6.25g (inc leads and sensor)

Especially made for FlySky FS-i10 and our Turnigy i10, this sun shade will enhance visibility of your LCD touch screen.

Simply peel and stick and fit directly around the screen area.  The shade collapses easily for storage/transport. 

As the old saying goes, the best just got better. This is definitely the case with the Turnigy TGY-i6S as it builds on the already great Turnigy-i6. The TGY-i6S still uses the solid and reliable 2.4GHz Automatic Frequency Hopping Digital System (AFHDS) spread spectrum technology. It is also a superb budget radio for both new and experienced pilots and is designed with multi-rotor / drone flying in mind. It can also be used for planes/gliders.

The Turnigy TGY-i6S is a 6-channel (PWM) or a 10-channel (PPM)  2.4GHz AFHDS Digital Proportional RC system. It comes complete with two receivers, the dependable TGY-iA6B 6 channel receiver and the new TGY-iA6C receiver for PPM or SBUS.

The new look design comes with some exciting new features. This radio incorporates a monochrome backlit LCD touchscreen making it easy to program and make changes in sunlight or at night. There are two internal dual omnidirectional high gain antennas (for more reliability) built inside the frame so they can’t be damaged in transit. To help control your aircraft there are lots of programmable switches, buttons, and scroll wheels. Making them great for setting up flight modes and the scroll wheels could be used for controlling camera gimbals. 

Standard 10A car esc with forward reverse and a good range of features such as timing adjust and breaking. Supports a wide range of motors. Very reliable!

HobbyKing® ™ X-Car Beast series ESCs offer excellent performance and features at a great price. With precise throttle linearity, smooth startup/acceleration, strong brakes and fully adjustable programming options, you will not find a better value in R/C car ESCs on the market today! 

Built with high quality components, and offering both sensored and senorless motor operation, this 1/8 Scale 150A series ESC offers truly versatile and high performance that won't break the bank.

Features:
• Enhanced throttle response for excellent accelleration
• Uses advanced PC interface to set up or update firmware
• Uses both LED and LCD program cards 
• Adjustable BEC output 6.0V/8.4V
• Multiple protection features including low voltage cut off protection, over heating protection and throttle/signal loss
• Compatible with NOVAK, LRP, ORION brushless motors

Specs:
Continuous Current: 150A
Burst: 1080A
Resistance: 0.0002ohms
Suitable Motor Type: 4 Pole sensorless and sensored brushless motor
Battery:  2 ~ 6S Lipoly   5~18S NiMH/NiCd
BEC Output: 6.0V ~ 8.4V adjustable/3A 
Dimensions: 55x48x37mm
Weight: 165g

This superb geared pump by Turnigy is perfect for filling all sizes of models whether large or small and it is suitable for either gas or glow fuels. Very easy to use, just push your electric starter onto the cone and spin it to either fill or empty, switch the valve over on the pump and it will change the direction of flow. The center of the cone also has a 6mm hex which will take the standard helicopter starting shaft.

This pump is extremely well made (much better than the average 12v electric fuel pump), the body is made from CNC metal parts and the internal gears are made of brass, apart from the valve there are only 2 moving parts so looked after it will last a very long time. Supplied with a filling nozzle, hook/loop tape and a clip so that you can make a strap to fit it to your fuel can.

Features:
• Very well made from CNC parts
• Fast fill or drain
• Few moving parts, very little to go wrong
• Use with your own electric starter

Size:
Length: 92mm
Width: 63mm
Height: 50mm (from face of cone to rear of backplate)
Weight: 245g

Alloy Anti-Slip TX Control Sticks Short (M4 for JR TX - Blue) - 12mm long + locknut, Total: 24mm

Alloy Anti-Slip TX Control Sticks Long (M4 for JR TX - Blue) - Complete with Locknut, 29.5mm Long

Alloy Anti-Slip TX Control Sticks Short (M4 for JR TX - Purple) - 12mm long + locknut, Total: 24mm

Alloy Anti-Slip TX Control Sticks Long (M4 for JR TX - Purple) - Complete with Locknut, 29.5mm Long

Alloy Anti-Slip TX Control Sticks Short (M4 for JR TX) - 12mm long + locknut, Total: 24mm

Alloy Anti-Slip TX Control Sticks Long JR TX (M4 Thread - Red) - Complete with Locknut, 29.5mm Long

Carbon Fibre Motor Mount with Countersunk Screws

NTM 28 Motor Mount Spacer/Stand Off 2mm (4pc)

Motor Mount Spacer Stand Off 2mm (4pc)

Motor Mount Spacer Stand Off 2mm (4pc)

10mm Shaft Universal Tri Motor Mount

Spec:
Shaft Size: 10mm
Inner Corner to Corner: 16mm
Outer Corner to Corner: 46mm
Weight: 5grams

10mm Shaft Universal Tri Motor Mount

Spec:
Shaft Size: 10mm
Inner Corner to Corner: 23mm
Outer Corner to Corner: 46mm
Weight: 7grams

11mm Shaft Universal Tri Motor Mount

Spec:
Shaft Size: 11mm
Inner Corner to Corner: 19mm
Outer Corner to Corner: 53mm
Weight: 6grams