Power Systems

Protect your OrangeRx receiver from damage and vibration with this protective silicone shell.Fits snuggly around most of the non satellite receivers and it has exit holes on the rear and side for the antennas.

Specs:
Length: 44.5mm
Width: 25mm
Height: 16mm
Weight: 6g

Laying down your radio is never an ideal situation and some transmitter stands just dont suit especially where a transmitter module has been fitted to the back, so why not use our latest single peg design.

Easily mounted on the carry handle, the stand will do its job quickly and easily and then fold away against the back of your transmitter. 

Made from machined alloy, this is a quality product and comes in a red anodised finish.

Weight: 27g

Laying down your radio is never an ideal situation and some transmitter stands just dont suit especially where a transmitter module has been fitted to the back, so why not use our latest single peg design.

Easily mounted on the carry handle, the stand will do its job quickly and easily and then fold away against the back of your transmitter. 

Made from machined alloy, this is a quality product and comes in a silver anodised finish.

Weight: 27g

The OrangeRx SF7003XS has all the properties and features of the original FASST compatible receivers in the OrangeRx brand but this one now operates on the later Futaba FHSS (Frequency Hopping Spread Spectrum) system. This receiver also has S-Bus and a built in 3 axis stabilizer which is brilliant in model airplanes to help beginners master the art of RC flying and for experienced pilots to make their flying even smoother. This receiver is perfect for the large gliders with long wingspans, it really helps to smooth out the turns and nose attitude when thermalling at higher altitudes.

The stabilizer function has 5 modes, mixer off, dual ailerons, V-tail mixing, delta mix and dual aileron/V-tail mixer. There are independent, simple to use gyro gain adjustments for the aileron, elevator and rudder functions, the stabilizer function can also be switched on and off in flight via CH5. The S.Bus functionality is perfect for large models and gliders that utilize a lot of servos, especially in the wings, it reduces the amount of wiring and keeps things nice and tidy.

The receiver will also accept a wide range of input voltages from 3.6~8.5V which is great if you want to use LV and HV type servos.

Compatible with the following Futaba FHSS 2.4Ghz air systems: 4YF, 6J, 8J and 10J, can also be used with the T14SG under S-FHSS protocol mode

Features:
• Lightweight (16g)
• Compatible with FHSS 2.4Ghz air systems
• 7 channels
• Built in 3 axis stabilizer
• 5 stabilizer modes
• Supports SBus
• Compact design (54 x 32 x 13mm)
• Failsafe and battery failsafe
• Extremely low latency
• Fast frame rates
• Hops from frequency to frequency in a pseudorandom sequence
• Advanced algorithms create a secure frequency

Specs:
Type: SF7003XS
Input Voltage: 3.6~8.5V
Operating Current: 60mA max
Battery Failsafe Voltage: 3.8V
Latency: 6.8mS
Sensitivity: About -96dBm
Dimensions: 54 x 32 x 13mm
Weight: 16g

Included:
OrangeRx SF7003XS receiver
Plastic screwdriver for making adjustments
Instruction manual

Note:
All OrangeRx receivers come with a 12 month warranty. This is not a Futaba receiver, nor is it a copy of a Futaba receiver. Futaba, FASST and FHSS are trademarks of Futaba Co (JP).

This small lightweight 4ch switch is extremely handy for auxillary functions on all sorts of models. Plug the single lead into an auxillary switched function then switch your radio on, channel 1 on the electronic switch will then be active, cycle the auxillary switch once and channel 1 goes out and channel 2 comes on, cycle the switch once more and 2 goes out and channel 3 comes and so on until it comes back to channel 1. When the radio is switched off and then switched back on the unit will default to channel 1 each time. This unit is great for switching lights on and off and other low current applications.

Please note: For this switch to work correctly you will need to set the related channel travel to +- 100%.

Specs:
Input Voltage: 4.8~7.4v
Output Voltage: 4.8~7.4v
Maximum Current: 2amps
Length: 40mm
Width: 20mm
Height: 12mm
Weight: 7g
Input Cable: 21cm (JR type plug)

Specs:
Maximum throughput : 10A / 30v
Weight: 7g

Especially made for FlySky FS-i10 and our Turnigy i10, this sun shade will enhance visibility of your LCD touch screen.

Simply peel and stick and fit directly around the screen area.  The shade collapses easily for storage/transport. 

Alloy Anti-Slip TX Control Sticks Short (M4 for JR TX - Blue) - 12mm long + locknut, Total: 24mm

Alloy Anti-Slip TX Control Sticks Long (M4 for JR TX - Blue) - Complete with Locknut, 29.5mm Long

Alloy Anti-Slip TX Control Sticks Short (M4 for JR TX - Purple) - 12mm long + locknut, Total: 24mm

Alloy Anti-Slip TX Control Sticks Long (M4 for JR TX - Purple) - Complete with Locknut, 29.5mm Long

Alloy Anti-Slip TX Control Sticks Short (M4 for JR TX) - 12mm long + locknut, Total: 24mm

Alloy Anti-Slip TX Control Sticks Long JR TX (M4 Thread - Red) - Complete with Locknut, 29.5mm Long

Alloy Anti-Slip TX Control Sticks Short (M3 for Futaba TX - Blue) - 12mm long + locknut, Total: 24mm

Turnigy 9XR FPV Monitor Mounting Arm.

A mounting arm specially designed to hold Telemetry units or FPV Monitors on
top of your 9XR.
Compatible with most standard FPV monitors and our Quanum Telemetry system.

*Requires the 9XR Transmitter Stand (see related items)

Trainer Port/RF PCB Assembly - Turnigy 9XR Transmitter

Mask (Chrome) - Turnigy 9XR Transmitter

Trim Tabs - Turnigy 9XR Transmitter (4set)

This is a stock replacement for your Turnigy 9XR transmitter faceplate and takes just minutes to install. Simply unbolt the original and replace with this.

Specs:
Application: Turnigy 9XR
Color: Silver

Customize your Turnigy 9XR with this optional colored faceplate!

Add a cool and custom look to your 9XR by simply bolting on this optional faceplate. Available in a variety of colors, you can make sure your 9XR will not get confused with others at your flying club.

This is a direct replacement for your stock 9XR faceplate and takes just minutes to install. Simply unbolt the original and replace with this.

Specs:
Application: Turnigy 9XR
Color: Metallic red

Customize your Turnigy 9XR with this optional colored faceplate!

Add a cool and custom look to your 9XR by simply bolting on this optional faceplate. Available in a variety of colors, you can make sure your 9XR will not get confused with others at your flying club.

This is a direct replacement for your stock 9XR faceplate and takes just minutes to install. Simply unbolt the original and replace with this.

Specs:
Application: Turnigy 9XR
Color: Gold

Customize your Turnigy 9XR with this optional colored faceplate!

Add a cool and custom look to your 9XR by simply bolting on this optional faceplate. Available in a variety of colors, you can make sure your 9XR will not get confused with others at your flying club.

This is a direct replacement for your stock 9XR faceplate and takes just minutes to install. Simply unbolt the original and replace with this.

Specs:
Application: Turnigy 9XR
Color: Metallic blue

Transmitter Neck Strap Adaptor (Blue)

Improve the stability of your 2.4ghz transmitter with one of these CNC anodised alloy neckstrap adaptors. 2 types of adaptors are supplied plus screws which will fit most radio's.

Transmitter Neck Strap Adaptor (Red)

Improve the stability of your 2.4ghz transmitter with one of these CNC anodised alloy neckstrap adaptors. 2 types of adaptors are supplied plus screws which will fit most radio's.

Transmitter Neck Strap Adaptor (Silver)

Improve the stability of your 2.4ghz transmitter with one of these CNC anodised alloy neckstrap adaptors. 2 types of adaptors are supplied plus screws which will fit most radio's.

Transmitter Neck Strap Adaptor (Gunmetal Black)

Improve the stability of your 2.4ghz transmitter with one of these CNC anodised alloy neckstrap adaptors. 2 types of adaptors are supplied plus screws which will fit most radio's.

This high quality switch is made in Taiwan and is proven to exceed more than 10000 switch cycles during testing.
This switch is designed for life time use.

Great for repairing your radio or making a swtich for your own project.

Spec.:
Style: 2-Way, Round Head
Dimension(LxWxD): 13x8x7mm(Plastic part only)
Length: 29mm(Switch & Mounting hole)
Mounting Hole Size: M6x8mm
Weight: 3.7g(Each)

This adjustable receiver antenna mount is a simple solution to ensure that you get the best range from your equipment.

Self-adhesive pads secure the mount to any flat surface on your model, while the knurled locking screw lets you alter the angle of antenna and fold them flat for transportation.

The antenna tubes can be cut to any length and provide a secure safe way to vertically mount your antennas.

Features:
• Optimal 45deg vertical mounting
• Adjustable angle
• Can be used with any long antenna receiver

Specs:
Weight: 6.6g
Size: 41 x 27 x 15mm
Tube length: 100mm

Included:
2 x Mounts
2 x Self-adhesive pads
4 x Antenna tubes

Easy to use, simply follow the links on the FrSKY website, connect the receiver to the STK and plug the STK into your computer via the USB port. The FrSKY STK updates all FrSKY receivers that support S.Port.

This handy programming box for the OrangeRx R620X to R1220X V3 and RR12RDTS receivers is perfect to have in your toolbox at the flying field in case you want to change the settings without the need for a PC. It has an integrated RF module that allows you to set up the receiver wirelessly or you can use a wired connection. As the RR12RDTS is primarily designed for drones and helicopters this programming box can also be used to adjust the settings of the flight stabilization systems.

FrSky M7-R hall sensor gimbal is specially designed for FPV racing, 3D and acrobatic fixed wing and 3D Heli pilots who are using the FrSky Taranis Q X7/X7S Transmitter. The 45°throttle travel will allow you to achieve a quick throttle response resulting in precision control.

This kit comes complete with the FrSky Taranis X-Lite BRACE. There are also red replacement gimbal stick ends in two sizes, short and long, depending on your needs.

If you are worried about scratching the Evolution PROs screen or damaging a control stick during transportation then this cover meets all your requirements. It simply clicks onto the front of your controller to safely guard the screen and sticks. It comes in black or white.

If you are worried about scratching the Evolution PROs screen or damaging a control stick during transportation then this cover meets all your requirements. It simply clicks onto the front of your controller to safely guard the screen and sticks. It comes in black or white.