Power Systems

The HobbyKing® ™ GT2B features 3 channel operation, interchangeable hand grips, adjustable steering dual-rate, servo reversing and a rechargeable li-ion battery which eliminates the need for buying expensive AA batteries. The li-ion battery also makes this transmitter much lighter, which gives the user a great feel during use. No more lugging around a heavy transmitter holding 8 x AA batteries!

Features:
• Reliable, interference free 2.4GHz AFHDS signal operation
• 3CH operation
• Rechargeable li-ion transmitter battery
• Interchangeable rubber hand grips
• Adjustable steering dual-rate
• Servo reversing

Transmitter Specs:
Model: Car/Boat
RF Power: 20dBm (100mW) max
Modulation: GFSK
System Type: AFHDS
Sensitivity: 1024
Low Voltage Warning: Yes
Charge Port: Yes (USB- charge cable included)
Power: 3.7V 800mAh li-ion (included)
Weight: 270g

Receiver Specs:
Model: Car/Boat
RF Receiver Sensitivity: -105dBm
Modulation: GFSK
System Type: AFHDS
Sensitivity: 1024
Failsafe: Yes
Power Port: Yes (VCC)
Power: 4.5~6.5 VDC 
Weight: 5g
Antenna Length: 26mm
Dimensions: 37.6 x 22.3 x 13mm

Includes:
HK-GT2B transmitter
HK-GT2B 3CH receiver
3.7V li-ion rechargeable battery pack
Optional second rubber hand grip
Antenna tube
USB charge cable
Bind plug
User manual

Especially made for FlySky FS-i10 and our Turnigy i10, this sun shade will enhance visibility of your LCD touch screen.

Simply peel and stick and fit directly around the screen area.  The shade collapses easily for storage/transport. 

As the old saying goes, the best just got better. This is definitely the case with the Turnigy TGY-i6S as it builds on the already great Turnigy-i6. The TGY-i6S still uses the solid and reliable 2.4GHz Automatic Frequency Hopping Digital System (AFHDS) spread spectrum technology. It is also a superb budget radio for both new and experienced pilots and is designed with multi-rotor / drone flying in mind. It can also be used for planes/gliders.

The Turnigy TGY-i6S is a 6-channel (PWM) or a 10-channel (PPM)  2.4GHz AFHDS Digital Proportional RC system. It comes complete with two receivers, the dependable TGY-iA6B 6 channel receiver and the new TGY-iA6C receiver for PPM or SBUS.

The new look design comes with some exciting new features. This radio incorporates a monochrome backlit LCD touchscreen making it easy to program and make changes in sunlight or at night. There are two internal dual omnidirectional high gain antennas (for more reliability) built inside the frame so they can’t be damaged in transit. To help control your aircraft there are lots of programmable switches, buttons, and scroll wheels. Making them great for setting up flight modes and the scroll wheels could be used for controlling camera gimbals. 

Alloy Anti-Slip TX Control Sticks Short (M4 for JR TX - Blue) - 12mm long + locknut, Total: 24mm

Alloy Anti-Slip TX Control Sticks Long (M4 for JR TX - Blue) - Complete with Locknut, 29.5mm Long

Alloy Anti-Slip TX Control Sticks Short (M4 for JR TX - Purple) - 12mm long + locknut, Total: 24mm

Alloy Anti-Slip TX Control Sticks Long (M4 for JR TX - Purple) - Complete with Locknut, 29.5mm Long

Alloy Anti-Slip TX Control Sticks Short (M4 for JR TX) - 12mm long + locknut, Total: 24mm

Alloy Anti-Slip TX Control Sticks Long JR TX (M4 Thread - Red) - Complete with Locknut, 29.5mm Long

Alloy Anti-Slip TX Control Sticks Short (M3 for Futaba TX - Blue) - 12mm long + locknut, Total: 24mm

Turnigy 9XR FPV Monitor Mounting Arm.

A mounting arm specially designed to hold Telemetry units or FPV Monitors on
top of your 9XR.
Compatible with most standard FPV monitors and our Quanum Telemetry system.

*Requires the 9XR Transmitter Stand (see related items)

Trainer Port/RF PCB Assembly - Turnigy 9XR Transmitter

Mask (Chrome) - Turnigy 9XR Transmitter

Trim Tabs - Turnigy 9XR Transmitter (4set)

This is a stock replacement for your Turnigy 9XR transmitter faceplate and takes just minutes to install. Simply unbolt the original and replace with this.

Specs:
Application: Turnigy 9XR
Color: Silver

Customize your Turnigy 9XR with this optional colored faceplate!

Add a cool and custom look to your 9XR by simply bolting on this optional faceplate. Available in a variety of colors, you can make sure your 9XR will not get confused with others at your flying club.

This is a direct replacement for your stock 9XR faceplate and takes just minutes to install. Simply unbolt the original and replace with this.

Specs:
Application: Turnigy 9XR
Color: Metallic red

Customize your Turnigy 9XR with this optional colored faceplate!

Add a cool and custom look to your 9XR by simply bolting on this optional faceplate. Available in a variety of colors, you can make sure your 9XR will not get confused with others at your flying club.

This is a direct replacement for your stock 9XR faceplate and takes just minutes to install. Simply unbolt the original and replace with this.

Specs:
Application: Turnigy 9XR
Color: Gold

Customize your Turnigy 9XR with this optional colored faceplate!

Add a cool and custom look to your 9XR by simply bolting on this optional faceplate. Available in a variety of colors, you can make sure your 9XR will not get confused with others at your flying club.

This is a direct replacement for your stock 9XR faceplate and takes just minutes to install. Simply unbolt the original and replace with this.

Specs:
Application: Turnigy 9XR
Color: Metallic blue

Transmitter Neck Strap Adaptor (Blue)

Improve the stability of your 2.4ghz transmitter with one of these CNC anodised alloy neckstrap adaptors. 2 types of adaptors are supplied plus screws which will fit most radio's.

Transmitter Neck Strap Adaptor (Red)

Improve the stability of your 2.4ghz transmitter with one of these CNC anodised alloy neckstrap adaptors. 2 types of adaptors are supplied plus screws which will fit most radio's.

Transmitter Neck Strap Adaptor (Silver)

Improve the stability of your 2.4ghz transmitter with one of these CNC anodised alloy neckstrap adaptors. 2 types of adaptors are supplied plus screws which will fit most radio's.

Transmitter Neck Strap Adaptor (Gunmetal Black)

Improve the stability of your 2.4ghz transmitter with one of these CNC anodised alloy neckstrap adaptors. 2 types of adaptors are supplied plus screws which will fit most radio's.

Increase your RC signal validity and reduce your probability of signal loss in carbon fiber and/or 3D airframes as well as long-range FPV platforms by using the OrangeRX DSMx/DSM2 compatible 6 Channel Diversity Module.

The OrangeRX DSM2/DSMx Compatible 6 Channel Diversity Module will receive data from up to 6 satellite receivers, check the signal validity, and then outputs the valid signal to any satellite interface-enabled DSM2/DSMx compatible receiver or via direct connection to a UAV or Flybarless Helicopter Flight Controller.

The unit can be powered from external 5V~8.4V or directly from the 3.3V satellite port and incorporates a binding function allowing satellites to be bound without using any additional receiver.

This high quality switch is made in Taiwan and is proven to exceed more than 10000 switch cycles during testing.
This switch is designed for life time use.

Great for repairing your radio or making a swtich for your own project.

Spec.:
Style: 2-Way, Round Head
Dimension(LxWxD): 13x8x7mm(Plastic part only)
Length: 29mm(Switch & Mounting hole)
Mounting Hole Size: M6x8mm
Weight: 3.7g(Each)

This adjustable receiver antenna mount is a simple solution to ensure that you get the best range from your equipment.

Self-adhesive pads secure the mount to any flat surface on your model, while the knurled locking screw lets you alter the angle of antenna and fold them flat for transportation.

The antenna tubes can be cut to any length and provide a secure safe way to vertically mount your antennas.

Features:
• Optimal 45deg vertical mounting
• Adjustable angle
• Can be used with any long antenna receiver

Specs:
Weight: 6.6g
Size: 41 x 27 x 15mm
Tube length: 100mm

Included:
2 x Mounts
2 x Self-adhesive pads
4 x Antenna tubes

The Orange OpenLRSng is an open-source receiver that can be programmed to use your choice of protocol and any channel in the 915MHz range. It is a fully user-customizable RF receiver that can even be programmed to utilize additional features such as telemetry, operative remote control via sticks (cPPM ready), and mission control.

The Orange OpenLRS 433MHz TX Module is designed for use with APM flight control software and can be programmed to use your choice of protocol and any channel in the 433MHz range. Fully user-customizable, the transmitter system can even be programmed to utilize additional features such as telemetry, operative remote control via stics (cPPM ready), and mission control.
It is equipped with Bluetooth technology so the user can connect it to a tablet, smartphone, or PC. All telemetry data, mission planning, and flight modes will be available in APM Mission Planner on PC or Droid Planner, or similar apps for Android devices. Thanks to the Bluetooth function, no additional leads are required to setup/program the transmitter module.

Extend your range and increase your link robustness with the OrangeRx cPPM receiver. This is the long antenna version making it ideal for FPV racing and for models with carbon fiber frames. The extra length of the antenna allows you to route them outside of the model.

OrangeRx receivers are built using original components, MCUs and with state of the art SMT automation to ensure a quality product each and every time. Every R618XL is manufactured using impedance matched PCBs with exact tuning to provide signal stability and range that exceeds any of the previous generation ORX products. In fact, our testing has shown that the R618XL exceeds the range of other receivers in the same class.

All R618XL OrangeRx receivers are QC tested using our latest method that ensures range checking takes place as the receiver is programmed. Simply put, if the R618XL cannot pass the range check it cannot be programmed, this ensures 100% of R618XL are guaranteed to work flawlessly.

The R618XL ushers in a new era of quality, reliability and performance for the OrangeRX line up.

This receiver features TRUE DIVERSITY technology. It is especially important for long range flights and in situations where you need more robust reception. It is also very useful in aircraft with carbon fiber frames where antenna can be in shadow of the airframe.

If one of the antennas cannot receive signal due to its orientation of airframe shadow, the satellite will use the other one and will still receive proper commands from transmitter. We tested these satellites in real flight tests many times and achieved 2 or more kilometers line of site performance. Please note that your range depends on the conditions in your place – interference, WiFi presence, obstacles and even air humidity.

This receiver has been tested and fully compatible with following flight controls:
- Naze32
- CC3D
- KK2
- MultiWii - APM(2.0 and up)
- V-Bar 5.3

Features:
• Compatible with DSM2/DSMX 1024/2048 aircraft radio and module systems
• 6 channel cPPM output allowing for single line connection with compatible devices
• Ultra fast brownout recovery and programmed fail safe mode
• Wide input voltage: 3.7~9.6V
• Long 145mm antenna

Spec:
Channels: 6
Frequency: 2.4Ghz
Modulation: GFSK
Sensitivity: up to -97dBm
Input voltage: 3.7~9.6V
Current consumption: 35mA
Range: 2km
Size: 19.5x30x10mm, 43x22x13mm with case
Weight: 3.7g / 9.8g with case
Wire Length: 210mm
Antennae Length: 145mm

Included:
OrangeRx R618XL PWM / cPPM Receiver (long antenna)
Bind Plug

Note:
1) This is not a Spektrum product, nor is it a copy of a Spektrum product. The Spektrum brand is a trademark of Horizon Hobbies USA.
2) This is not an underground black market fake Spektrum Satellite. OrangeRx quality is guaranteed.

Compatible with all DSM2/DSMX 2.4GHz air transmitters and now featuring either CPPM or S.Bus output, the OrangeRx R620Xto R1220X V2 range takes things to the next level by offering either CPPM or S.Bus output, true DSMX compatibility, integrated telemetry and utilizes dual antennae providing true signal reception diversity! Add to this programmable failsafe on binding, ultra-fast brown-out recovery and wide voltage input range. The end result being an unbeatable value for money aircraft receiver! The new V2 version has improved antenna switching algorithm and redesigned RF front end portion that extend the control range 2km or more and telemetry 400m or more! 

The OrangeRx 6ch compact receiver has been designed for FPV racing drones with carbon frames. The extra-length antenna allows you to route them outside of the frame for extended range and a robust link to your transmitter.

OrangeRx receivers are built using original components, 32-bit MCUs, and with state of the art SMT automation to ensure a quality product each and every time. Every single receiver is manufactured using impedance-controlled PCBs with exact tuning to provide signal stability and range that exceeds any of the previous generation ORX products. In fact, our testing has shown that the R617XL exceeds the range of other receivers in the same class.

All R617XL OrangeRx receivers are QC tested using our latest method that ensures range checking takes place as the receiver is programmed. Simply put, if the R617XL cannot pass the range check it cannot be programmed, this ensures 100% of R617XLs are guaranteed to work flawlessly. The R617XL ushers in a new era of quality, reliability, and performance for the OrangeRx lineup.

The receiver features "True Diversity" technology, which is especially important for long-range flights and in situations where you need that more robust reception. This receiver is very useful where carbon is used in the construction of your model where the antenna can be in the shadow of the airframe. If one of the antennae cannot receive a signal due to its orientation then the satellite will use the other one to receive the commands from the transmitter.

The OrangeRX 2.4Ghz transmitter module offers a simple, convenient and inexpensive way to utilize your module-based JR/Turnigy/Taranis compatible transmitter to enable its compatability with any DSM2 and DSMX type receivers. 

Unlike standard modules which have a fixed protocol, this unit switches automatically between DSM2 compatible (1024/22ms, 2048/11ms) and DSMX compatible (22ms, 11ms) during the binding process. It is also manually selectable using a long press of the bind button.

This version also has a major firmware change that allows for the module to work with multiple receivers without rebinding.

Simply remove your existing module, plug in the OrangeRX  module and you are ready to bind to any DSMX, DSM2 compatible receivers. 

Features:
• Works with any JR/Turnigy/Taranis compatible module-based transmitter
• Auto and manual mode switching: DSM2 compatible 1024/22ms, DSM2 compatible 2048/11ms, DSMX compatible 22ms, DSMX compatible 11ms
• Easy to access bind button
• Easy to use ID button 
• Range check mode (1mW)
• Full range system
• Accepts PPM from 4 - 12 channels
• Outputs from 4 - 12 channels according to PPM provided
• Low current consumption

Specs:
Compatibility: JR style 5 pin module-based transmitters (JR/Turnigy/Taranis compatible) (Not compatible with Turnigy 9X)
2.4Ghz protocol: DSMX / DSM2 compatible
Input Voltage: 6 - 18VDC
Output Power: -18dBm
Current Consumption: 100mA max
Radio Type: Full range system
Firmware version: 1.2

Includes:
OrangeRX DSMX/DSM2/Devo Compatible 2.4Ghz transmitter module
2.4Ghz antenna
For manual please see files tab below.

Note:
OrangeRX Modules use a unique Global ID for binding. Incase of binding issues with other branded receivers press the "Change ID" button on module to change the Module ID to another unique value reserved for that module. There are over 4 billion unique ID's assigned to OrangeRx modules.

Note:
This is not a Spektrum DSM2/X, Walkera product, neither is it a copy of a Spektrum DSM2/DSMX/Walkera product. The Spektrum and DSM2 / DSMX brand is a trademark of Horizon Hobbies USA. OrangeRX products are not black market or fake Spektrum products. OrangeRx quality is guaranteed. 

OrangeRx™ have created another excellent receiver after listening to customer feedback. This lightweight 3.9g comes in a soft case to keep the weight down and can be used in multirotor or other applications where there is no need for a hard case to protect the receiver.

Compatible with all DSM2 2.4GHz Air transmitters and now featuring CPPM!

The OrangeRx R610V2 lite takes things to the next level by offering CPPM, true DSM2 compatibility and utilizes dual antennae providing true signal reception diversity! Add to this programmable failsafe on binding, ultra fast brown-out recovery and wide voltage input range. The end result being an unbeatable value for the money multirotor/aircraft receiver!

The all new CPPM functionality is an excellent feature for use with multi-rotor flight controllers such as the KK2.1, APM, MultiWii and others. This single line connection removes the weight and mess of additional wire leads for each individual channel. This is ideal for use on small frames where space is at a premium.

OrangeRx receivers are built using original components, MCUs and with state of the art SMT automation to ensure a quality product each and every time. Every R610V2 is manufactured using impedance matched PCBs with exact tuning to provide signal stability and range that exceeds any of the previous generation ORX products. In fact, our testing has shown that the R610V2 exceeds the range of other receivers in the same class.

All R610V2 Lite OrangeRx receivers are QC tested using our latest method that ensures range checking takes place as the receiver is programmed. Simply put, if the R610V2 Lite cannot pass the range check it cannot be programmed, this ensures 100% of R610V2 Lite are guaranteed to work flawlessly.

The R610V2 heralds a new era of quality, reliability and performance for the OrangeRX line up.

Features:
• Super lightweight 3.9g (with shrink tube)
• DSM2 compatibility
• CPPM output allowing for single line connection with compatible CPPM devices
• Short 25mm antennae for mounting in almost any location
• Wide input voltage: 3.7~9.6V
• 6 Channels
• Compact design

Specs:
Channels: 6
Input voltage: 3.7~9.6V
Size: 41x18x10mm
Weight: 3.9g

Servo Tape (Clear) 25mm x 1m

This awesome servo tape is super strong and when the backing is removed it is completely clear. This tape has the amazing property of being very sticky and will securely fasten your servos, receivers, speed controls and transponders to your aeroplane, helicopter car or boat, yet when you wish to remove them, they come right off without the servo tape breaking apart plus there is no residue left on the surface!!

Very clean, very secure and incredibly versatile.

Size
Width: 25mm
Depth: 1mm
Length: 1m

Walkera F210 Racing Quad – DEVO-RX713 Receiver

Part No: F210-Z-25

There's a lot to be said for the simple things in life, and with RC equipment becoming ever more flexible it's a refreshing change to find a simple, 4 channel radio that dispenses with the need for programming before you can use it.

The Turnigy TGY-i4X AFHDS/2A does exactly that and is a great entry level 4-channel telemetry 2.4ghz transmitter that can be switched between 1st and 2nd generation Automatic Frequency Hopping Digital System (AFHDS 2A) spread spectrum technology. The Turnigy TGY-i4X has a nice quality look and feel, while the programming is limited to one-switch V-tail/elevon mixing and servo reversing only. The transmitter is capable of being upgraded to up to 10 channels, see manual for details.

An ergonomically designed, ultra slim case design fits comfortably in your hands, an advantage during long flights. Digital trims and easy to read battery indicator LEDs give the TGY-i4X a modern feel with all the essential features you need. With a low profile antenna, the TGY-i4X is easy to transport and store. Adjustable length sticks, and a loop for attaching a neck strap round out the list of comfort features this radio offers.

The TGY-i4X comes with the TGY-i4X 4-channel receiver and is a superb budget radio for both new and experienced pilots alike!

Features:
• Entry level 4 channel 2.4ghz radio
• One switch V-tail/elevon mixer
• Easy to use servo reversing switches
• Standard Wing/Elevon/V-Tail
• Trainer port
• Simple LED battery indicator
• 1-Button binding

Transmitter Specs:
Channels: 4 (Expandable to 10)
Frequency: 2.40~2.48GHz
Bandwidth: 500KHz
DSC Port: PS2
Output: PPM Charger
Modulation: GFSK
Spread Spectrum Mode: AFHDS 2A and AFHDS
Band: 142 RF
Number of Frequency Channels: 20
Output Power: <=20dbm
Working Current: <=100mA
Working Voltage: 6V (4 x AA batteries)
Range: 100~300m
Dimensions: 174 x 89 x 190mm
Weight: 335g
Resolution: 1024 bit
Stick Mode: Mode 2 (Throttle Left)

Receiver Specs:
Channel: 4
Frequency: 2.40~2.48GHz
Power: 4.5V~6.6V/<30ma
Weight: 13g
Antenna length: 26mm
Dimensions: 45 x 23 x 9mm

Included:
Turnigy TGY-i4X transmitter
Turnigy TGY-i4X receiver
Bind plug
Manual

Requires:
4 x AA batteries

Instruction Manual is available under the "Files" tab.