Cars

These replacement drivers have been specifically designed to fit the Turnigy high quality drivers and drive sets (rubber handled type). The replacement shafts are manufactured from high tensile steel and are hard coated to prevent corrosion.

Specs:
Drive Type: Flat head screwdriver
Tip Size: 5mm
Shaft Diameter: 5mm
Shaft Length: 120mm
Weight: 17.06g

TrackStar TS3t Temperature Sensor for Electric Car/Boat

Specs:
Lenght: 390mm
Plug: JR plug

TrackStar Shock End Caps 12mm (4)

Compatible with the following Shock Absorbers
S12400, S160023, S160026, S160085, S160100

TrackStar Suspension Spring Retainer 12mm (4)

Compatible with the following Shock Absorbers
S12400, S160023, S160026, S160085, S160100

TrackStar Big Bore Suspension Spring Retainer 13mm (4) S124103

Compatible with the following Shock Absorbers
S124300, S160323, S160326

TrackStar Shock Bottom Cap Set with O-Ring S120052

Compatible with the following Shock Absorbers
S12400, S160023, S160026, S160085, S160100, S124300, S160323, S160326

TrackStar Hardened Shock Shaft (x4)

Specs:
Diameter: 3.2mm
Length:48mm

Compatible with the following Shock Absorbers
S160100

TrackStar Suspension Spring (x4)

Specs:
Wire Thickness: 1.1mm
Internal Diameter: 14mm
Length:55mm
Spring Rate:  1.8Kg
Color: Red

Compatible with the following Shock Absorbers
S160023, S160026, S160323, S160326

TrackStar Suspension Spring (x4)

Specs:
Wire Thickness: 1.1mm
Internal Diameter: 14mm
Length:55mm
Spring Rate:  1.5Kg
Color: Silver

Compatible with the following Shock Absorbers
S160023, S160026, S160323, S160326

TrackStar Suspension Spring (x4)

Specs:
Wire Thickness: 1.1mm
Internal Diameter: 14mm
Length: 55mm
Spring Rate:  1.2Kg
Color: Gold

Compatible with the following Shock Absorbers
S160023, S160026, S160323, S160326

TrackStar Suspension Spring (x4)

Specs:
Wire Thickness: 1.1mm
Internal Diameter: 14mm
Length: 65mm
Spring Rate:  2.1Kg
Color: Red

Compatible with the following Shock Absorbers
S160085, S160100

TrackStar Suspension Spring (x4)

Specs:
Wire Thickness: 1.1mm
Internal Diameter: 14mm
Length: 65mm
Spring Rate:  1.8Kg
Color: Silver

Compatible with the following Shock Absorbers
S160085, S160100

TrackStar Suspension Spring (x4)

Specs:
Wire Thickness: 1.1mm
Internal Diameter: 14mm
Length:65mm
Spring Rate:  1.5Kg
Color: Gold

Compatible with the following Shock Absorbers
S160085, S160100

TrackStar Suspension Spring (x4)

Specs:
Wire Thickness: 1.1mm
Internal Diameter: 14mm
Length:65mm
Spring Rate:  1.2Kg
Color: Blue

Compatible with the following Shock Absorbers
S160085, S160100

1/10 scale aluminum hooks with 920mm steel chain.

Specs:
Length: 820mm
Weight: 24g

Turnigy Programmable Lipo Battery Warmer Bag - Lipo's can lose up to 40% of their capacity when used in cold weather. This of course will drastically shorten flight/drive times and of course performance. This superb Turnigy lipo warmer is perfect for the RC enthusiast who is flying/driving in cold weather/climate and also for competition pilots/drivers looking to squeeze every ounce of capacity from their battery for optimum performance, even in warm ambient temperatures.

You can select the desired temperature via the simple to operate buttons/LED display on the front of the bag, the inbuilt microprocessor offers a 7 step heater range from 25ºC ~ 45ºC (77ºF ~ 113ºF) and the sealable bag, which is lined with a heat reflective material, keeps your lipo snug and ready to use.

Specs:
Input Voltage: 10v ~ 13v DC
Idle Current: <30mAh
Working Current: 2A
Programmable Temp Value: 25/27.5/30/32.5/35/40/45ºC (2 button -/+ operation with LED display)
Operating Temp: -10ºC ~ 45ºC
Dimensions Overall: 295mm x 230mm
Dimensions Lipo Cavity: 195mm x 230mm
Weight: 135g
Connector: XT-60 + Croc Clip Lead (supplied)

TrackStar SEG 21 Racing Engine replacement rear cover.

*Color may vary

HobbyKing is now proud to offer the famous Bittydesign approved 1/10 190mm Racing Body Shell and Body accessories!

The Striker-SR 3.0 version body has been developed for many months with several tests with the result of real fast bodyshell that combines a steering efficiency togheter with highest rear stability. It comes with big efra spec downforce rear wing that provide the best balance from front/rear axle of your car.

The bodyshell is EFRA, IFMAR, ROAR and BRCA approved.

The body is particular indicated for surfaces with a high level of grip, the use of our "Ultra Charge" Hard wing is suggested.

Features:
• The body comes with a complete set of lightweight big plastic washers to fix the rear wing perfectly. Steel screws nuts are includeds in the kit (you don't need to purchase any aftermarket accessory to fix our wing)

• Lightweight 0.75mm thickness
• EFRA, IFMAR, ROAR and BRCA approved
• Best performances on high grip surfaces
• Made with high quality polycarbonate
• Clear body sold with Protective film
• Windows masks & decals sheet included

*Note: Body shell requires finishing such as painting, cutting out of the wheel wells and applying decals.

The Precision Spur Gear R2 83T is specially designed for 1/10th scale vehicles using hex type slipper pads such as Team Associated off-road vehicles and a great upgrade for your BZ-222. The Revision 2 version of the gears are precision machined from specially formulated composite material to ensure highest strength, low running noise and excellent reliability. 

The increased contact area improves durability without sacrificing efficiency. The precision machining not only increases the durability of the gears but also provides an improved gear mesh.

All gears feature machined vents and weight reducing holes to minimize heat build-up when running a soft slipper clutch setting. The gears are engraved with size markings for easy identification.

Features:
• Machined composite material for increased strength, low noise and improved reliability
• Increased contact area
• Machined vents and weight reducing holes to minimize heat build-up
• Engraved markings for easy identification

Specs:
Size: 48DPX 83T
Material: Composite
Weight: 5.7g

Screw Grub Hex M5x5mm (10pcs/pack)

Turnigy Pure-Silicone Wire 12AWG (1mtr) Translucent Red is the final touch of bling for your next RC project. Not only will these cool wires give your model an individual look but their super soft flexibility makes them easier to fit into restrictive spaces and around tight corners.  

Features:
• High quality TURNIGY silicone wire.
• High strand count.
• Pure copper & pure silicone.

Specs:
Temp rating: 200° C
Gauge: 12 AWG
Length: 1m
Colour: Translucent Red

Turnigy Pure-Silicone Wire 12AWG (1mtr) Translucent Black is the final touch of bling for your next RC project. Not only will these cool wires give your model an individual look but their super soft flexibility makes them easier to fit into restrictive spaces and around tight corners.  

Features:
• High quality TURNIGY silicone wire.
• High strand count.
• Pure copper & pure silicone.

Specs:
Temp rating: 200° C
Gauge: 12 AWG
Lenght: 1m
Colour: Translucent Black

Turnigy 1/2" Hex Socket Screwdriver
Ultra strong steel tip, wont break or round like other cheap drivers.
Lightweight, hollow alloy handle means it wont weigh down your R/C gear case.

Turnigy 3/8" Hex Socket Screwdriver
Ultra strong steel tip, wont break or round like other cheap drivers.
Lightweight, hollow alloy handle means it wont weigh down your R/C gear case.

The Turnigy V2 range of drivers: comfortable, high quality, precision tools at a price that can't be beaten.

The Turnigy V2 range of drivers: comfortable, high quality, precision tools at a price that can't be beaten.

The Turnigy V2 range of drivers: comfortable, high quality, precision tools at a price that can't be beaten.

Replacement 2.5mm Arm Reamer Tip for Turnigy V2 series drivers.  The shafts are manufactured from spring steel to provide superior durability and a tight clean fit in the screw head. 

Replacement 3.0mm Arm Reamer Tip for Turnigy V2 series drivers.  The shafts are manufactured from spring steel to provide superior durability and a tight clean fit in the screw head. 

Replacement 4.0mm Arm Reamer Tip for Turnigy V2 series drivers.  The shafts are manufactured from spring steel to provide superior durability and a tight clean fit in the screw head. 

The Turnigy V2 range of drivers: comfortable, high quality, precision tools at a price that can't be beaten.

The Turnigy V2 range of drivers: comfortable, high quality, precision tools at a price that can't be beaten.

Enhance the scale appearance of your drifter or scale crawler with these clever, hidden magnetic fixings.