Vehicles

Enhance the scale appearance of your drifter or scale crawler with these clever, hidden magnetic fixings.

This simple and effective charge lead comes pre-soldered with standard 4mm bullet connectors at the charger end and has stepped, bullet connectors at the battery end allowing you to charge hard case packs that utilise 4mm and 5mm connectors. 

Ultra-Cure Tire Glue has a water-thin viscosity that wicks deep into the bead of the tire and cures in a matter of a few seconds. The tire bead must be tight fitting and should be held together while you apply the CA around the edges of the seam.

TrackStar 30mm High-Speed Cooling Fan

This Mini Vibrating Cleaning set is perfect for removing grease, dust, and other contaminants from small objects. Ideal for bearings, gears, springs, shafts, jewelry, watch parts, and even small precision instruments.

This bearing detergent is the perfect partner to Mini Vibrating Cleaning Unit. Mix this detergent with water for removing grease, dust and other contaminants from bearings, gears, watch parts, jewelry and lots of other small intricate parts.

A compact battery adapter to convert a T-Connector battery lead to a TR output, compatible with similar types of connectors.

A compact battery adapter to convert an EC5 battery lead to a TR output, compatible with similar types of connectors.

A compact battery adapter to convert an EC3 battery lead to a TR output, compatible with similar types of connectors.

A compact battery adapter to convert an XT60 battery lead to a TR output, compatible with similar types of connectors.

A compact battery adapter to convert an XT90 battery lead to a TR output, compatible with similar types of connectors.

This compact and user-friendly LCD program box will allow you to very easily change the parameters of your Turnigy TrackStar brushless car electronic speed controllers. The actual parameters that can be adjusted are dependent on the model of TrackStar brushless car ESC connected. This multifunction unit also has a handy built-in battery checker suitable for up to 8S LiPo batteries.

Turnigy Pure-Silicone Wire 12AWG (1mtr) Translucent Red is the final touch of bling for your next RC project. Not only will these cool wires give your model an individual look but their super soft flexibility makes them easier to fit into restrictive spaces and around tight corners.  

Features:
• High quality TURNIGY silicone wire.
• High strand count.
• Pure copper & pure silicone.

Specs:
Temp rating: 200° C
Gauge: 12 AWG
Length: 1m
Colour: Translucent Red

Turnigy Pure-Silicone Wire 12AWG (1mtr) Translucent Black is the final touch of bling for your next RC project. Not only will these cool wires give your model an individual look but their super soft flexibility makes them easier to fit into restrictive spaces and around tight corners.  

Features:
• High quality TURNIGY silicone wire.
• High strand count.
• Pure copper & pure silicone.

Specs:
Temp rating: 200° C
Gauge: 12 AWG
Lenght: 1m
Colour: Translucent Black

Turnigy 1/2" Hex Socket Screwdriver
Ultra strong steel tip, wont break or round like other cheap drivers.
Lightweight, hollow alloy handle means it wont weigh down your R/C gear case.

Turnigy 3/8" Hex Socket Screwdriver
Ultra strong steel tip, wont break or round like other cheap drivers.
Lightweight, hollow alloy handle means it wont weigh down your R/C gear case.

HobbyKing is now proud to offer the famous Bittydesign approved 1/10 190mm Racing Body Shell and Body accessories!

The Striker-SR 3.0 version body has been developed for many months with several tests with the result of real fast bodyshell that combines a steering efficiency togheter with highest rear stability. It comes with big efra spec downforce rear wing that provide the best balance from front/rear axle of your car.

The bodyshell is EFRA, IFMAR, ROAR and BRCA approved.

The body is particular indicated for surfaces with a high level of grip, the use of our "Ultra Charge" Hard wing is suggested.

Features:
• The body comes with a complete set of lightweight big plastic washers to fix the rear wing perfectly. Steel screws nuts are includeds in the kit (you don't need to purchase any aftermarket accessory to fix our wing)

• Lightweight 0.75mm thickness
• EFRA, IFMAR, ROAR and BRCA approved
• Best performances on high grip surfaces
• Made with high quality polycarbonate
• Clear body sold with Protective film
• Windows masks & decals sheet included

*Note: Body shell requires finishing such as painting, cutting out of the wheel wells and applying decals.

The Precision Spur Gear R2 83T is specially designed for 1/10th scale vehicles using hex type slipper pads such as Team Associated off-road vehicles and a great upgrade for your BZ-222. The Revision 2 version of the gears are precision machined from specially formulated composite material to ensure highest strength, low running noise and excellent reliability. 

The increased contact area improves durability without sacrificing efficiency. The precision machining not only increases the durability of the gears but also provides an improved gear mesh.

All gears feature machined vents and weight reducing holes to minimize heat build-up when running a soft slipper clutch setting. The gears are engraved with size markings for easy identification.

Features:
• Machined composite material for increased strength, low noise and improved reliability
• Increased contact area
• Machined vents and weight reducing holes to minimize heat build-up
• Engraved markings for easy identification

Specs:
Size: 48DPX 83T
Material: Composite
Weight: 5.7g

Screw Grub Hex M5x5mm (10pcs/pack)