Vehicles

This is a very neat device for securing your models hatches. This latch is spring loaded so once latched your canopy stays put!

Specs:
Dimensions: 26 x 16 x 8mm + 15mm pin length 
Material: Aluminum

This is a very neat device for securing your models hatches. This latch is spring loaded so once latched your canopy stays put!

Specs:
Dimensions: 23.5 x 13 x 8mm + 8mm pin length
Material: Plastic / Steel

This is a very neat device for securing your models hatches. This latch is spring loaded so once latched your canopy stays put!

Specs:
Dimensions:  26x16x10mm + 10mm pin Length
Material: Plastic / brass

63mm TurnFin Set L&R - Suit HobbyKing Vanquish 1075MM BOAT

Spec.:
Height: 63mm
Width: 24.7mm
Weight: 32g

A 1/10 scale model of a typical Formula-1 tunnel hull racing boat that is a stunning design and made of high quality fiberglass, it is beautifully finished in high gloss gel-coat and has eyecatching graphics already applied.

This is a hull only so that you can customize your own motor, ESC,  battery and radio set up to make this one really fast boat.

Specs:
Length: 650mm
Width: 270mm
Height: 190mm
Weight: 730g (hull only)

Required:
540 size outboard motor unit
ESC to suit above unit
2~3S 3000mah to 4000mah lipoly battery
1 x standard size servo
1 set of steering linkages
2ch transmitter and receiver system

Land yachting combines the grace of sailing with the thrill of motor racing. It's great to watch your land yacht skimming across smooth hard sand or a large tarmac area at high speed and with no noise just using the wind.

Full size land yachts hold speed records of over 126mph sailing at 3-4 times faster than the wind that propels them and now you too can enjoy the challenge and thrills of land yachting with the HobbyKing Bat 1 RC land yacht.

The Bat 1 has been designed by a renowned RC and full size land yacht pilot and it is available in 3 versions, "Almost Ready to Run", "plug & play" and in "Kit" form. All versions have a simple, rugged construction and are very straightforward to assemble. The Bat 1 utilises just 2 channels, one for steering and one for controlling the sail, it also has low friction ballraced wheels for super smooth free running and a colorful eye catching sail finishes the Bat 1 off nicely.

Following on from the success of the YEP speed controllers we now have a watercooled version for marine use. It has all the fantastic features of the other version but this one also incorporates a water cooling system and the entire ESC has been coated in a water-proof compound for protection against moisture. The features include super smooth start and ultra high resolution throttle response which puts these ESC's in a class of their own.

Following on from the success of the YEP speed controllers we now have a watercooled version for marine use. It has all the fantastic features of the other version but this one also incorporates a water cooling system and the entire ESC has been coated in a water-proof compound for protection against moisture. The features include super smooth start and ultra high resolution throttle response which puts these ESC's in a class of their own.

The Turnigy AquaStar Sensorless Brushless Motors offer outstanding performance for your boat at an incredible price!

Featuring a quality CNC machined billet T6 aluminum motor can, hand-wound high purity copper windings and powerful sintered neodymium magnet, you wont find a better priced motor of this caliber anywhere else!  It even features a billet aluminum water cooling jacket pre-installed.

The AquaStar brushless motors are a great choice for your deep-V, hydro or catamaran race boat and will be sure to leave the competition in your wake!

Features:              
• CNC machined billet T6 aluminum motor can 
• High purity copper windings
• 4mm bullet connectors pre-installed   
• Powerful sintered neodymium magnet   
• Precision engineered for maximum energy conversion
• Water cooling jacket pre-installed

Specs:
RPM/v: 1700kv
Poles: 4
Max voltage: 22.2v (6S)
Max Current: 84A
Max Watts: 1800w
Resistance: 0.0094ohm
No Load Current: 2.9A
Can Diameter: 36mm (actual motor diameter)
Can Diameter inc. Water Jacket: 44mm
Can Length: 60mm
Shaft Size: 5mm
Weight: 270g

The Turnigy AquaStar Sensorless Brushless Motors offer outstanding performance for your boat at an incredible price!

Featuring a quality CNC machined billet T6 aluminum motor can, hand-wound high purity copper windings and powerful sintered neodymium magnet, you will not find a better priced motor of this caliber anywhere else!  It even features a billet aluminum water cooling jacket pre-installed.

The AquaStar brushless motors are a great choice for your deep-V, hydro or catamaran race boat and will be sure to leave the competition in your wake!

Features:              
• CNC machined billet T6 aluminum motor can 
• High purity copper windings
• 4mm bullet connectors pre-installed   
• Powerful sintered neodymium magnet   
• Precision engineered for maximum energy conversion
• Water cooling jacket pre-installed

Specs:
RPM/v: 1460kv
Poles: 4
Max voltage: 25.9v (7S)
Max Current: 72A
Max Watts: 1800w
Resistance: 0.0094ohm
No Load Current: 2.9A
Can Diameter: 36mm (actual motor diameter)
Can Diameter inc. Water Jacket: 44mm
Can Length: 60mm
Shaft Size: 5mm
Weight: 270g

TURNIGY XK motors are without question one of the best motors on the market today. It all starts in our very own factory where we install precision bearings, correctly rated magnets, balanced rotors, tool-steel shafts and stators that are wound by hand. We rigorously test each and every component at 14 critical points during construction, testing everything from materials all the way through to final performance tests.

Because we design and build these motors completely in-house we control the production and ensure product consistency from design right through to shipping. We removed the middle-man to bring you factory prices while not sacrificing quality or performance. 

Features:
• Hand-wound for maximum copper fill.
• Precision-balanced rotor will boost the efficiency and power performance of the motor.
• Nickel-plated sintered neodymium rotor for maximum motor acceleration, braking power and performance in high-temperature conditions.

Specs:
Motor size: 4074
Number of pole: 4
Motor KV: 2000
Max Current: 120A
Max Voltage: 25V / 6S Lipoly
Case Length: 74mm
Case Dia: 40mm
Shaft Dia: 5.0mm
Total Length: 91mm
Weight: 380g

TURNIGY XK motors are without question one of the best motors on the market today. It all starts in our very own factory where we install precision bearings, correctly rated magnets, balanced rotors, tool-steel shafts and stators that are wound by hand. We rigorously test each and every component at 14 critical points during construction, testing everything from materials all the way through to final performance tests.

Because we design and build these motors completely in-house we control the production and ensure product consistency from design right through to shipping. We removed the middle-man to bring you factory prices while not sacrificing quality or performance. 

Features:
• Hand-wound for maximum copper fill.
• Precision-balanced rotor will boost the efficiency and power performance of the motor.
• Nickel-plated sintered neodymium rotor for maximum motor acceleration, braking power and performance in high-temperature conditions.

Specs:
Motor size: 3650
Number of pole: 4
Motor KV: 5400
Max Current: 135A
Max Voltage: 12.6V / 3S Lipoly
Case Length: 50mm
Case Dia: 36mm
Shaft Dia: 3.175mm
Total Length: 67mm
Weight: 200g

TURNIGY XK motors are without question one of the best motors on the market today. It all starts in our very own factory where we install precision bearings, correctly rated magnets, balanced rotors, tool-steel shafts and stators that are wound by hand. We rigorously test each and every component at 14 critical points during construction, testing everything from materials all the way through to final performance tests.

Because we design and build these motors completely in-house we control the production and ensure product consistency from design right through to shipping. We removed the middle-man to bring you factory prices while not sacrificing quality or performance. 

Features:
• Hand-wound for maximum copper fill.
• Precision-balanced rotor will boost the efficiency and power performance of the motor.
• Nickel-plated sintered neodymium rotor for maximum motor acceleration, braking power and performance in high-temperature conditions.

Specs:
Motor size: 3665
Number of pole: 4
Motor KV: 3190
Max Current: 95.2A
Max Voltage: 16.8V / 4S Lipoly
Case Length: 65.5mm
Case Dia: 36mm
Shaft Dia: 5.0mm
Total Length: 85.2mm
Weight: 275g

TURNIGY XK motors are without question one of the best motors on the market today. It all starts in our very own factory where we install precision bearings, correctly rated magnets, balanced rotors, tool-steel shafts and stators that are wound by hand. We rigorously test each and every component at 14 critical points during construction, testing everything from materials all the way through to final performance tests.

Because we design and build these motors completely in-house we control the production and ensure product consistency from design right through to shipping. We removed the middle-man to bring you factory prices while not sacrificing quality or performance. 

TURNIGY XK motors are without question one of the best motors on the market today. It all starts in our very own factory where we install precision bearings, correctly rated magnets, balanced rotors, tool-steel shafts and stators that are wound by hand. We rigorously test each and every component at 14 critical points during construction, testing everything from materials all the way through to final performance tests.

Because we design and build these motors completely in-house we control the production and ensure product consistency from design right through to shipping. We removed the middle-man to bring you factory prices while not sacrificing quality or performance. 

Features:
• Hand-wound for maximum copper fill.
• Precision-balanced rotor will boost the efficiency and power performance of the motor.
• Nickel-plated sintered neodymium rotor for maximum motor acceleration, braking power and performance in high-temperature conditions.

Spec.:
Size: XK3674-2200KV
Poles: 4
KV: 2200
Max Current: 70A
Max Voltage: 25.2V/6S Lipo
Max Watts: 1750w
Case Length: 74mm
Case Dia: 36mm
Shaft Dia: 5.0mm
Total Length: 91.2mm
Weight: 310g

TURNIGY XK motors are without question one of the best motors on the market today. It all starts in our very own factory where we install precision bearings, correctly rated magnets, balanced rotors, tool-steel shafts and stators that are wound by hand. We rigorously test each and every component at 14 critical points during construction, testing everything from materials all the way through to final performance tests.

Because we design and build these motors completely in-house we control the production and ensure product consistency from design right through to shipping. We removed the middle-man to bring you factory prices while not sacrificing quality or performance. 

Features:
• Hand-wound for maximum copper fill.
• Precision-balanced rotor will boost the efficiency and power performance of the motor.
• Nickel-plated sintered neodymium rotor for maximum motor acceleration, braking power and performance in high-temperature conditions.

Spec.:
Size: XK3674-1900KV
Poles: 4
KV: 1900
Max Current: 61A
Max Voltage: 29.4V/7S Lipo
Case Length: 74mm
Case Dia: 36mm
Shaft Dia: 5.0mm
Total Length: 91.2mm
Weight: 310g

TURNIGY XK motors are without question one of the best motors on the market today. It all starts in our very own factory where we install precision bearings, correctly rated magnets, balanced rotors, tool-steel shafts and stators that are wound by hand. We rigorously test each and every component at 14 critical points during construction, testing everything from materials all the way through to final performance tests.

Because we design and build these motors completely in-house we control the production and ensure product consistency from design right through to shipping. We removed the middle-man to bring you factory prices while not sacrificing quality or performance. 

Features:
• Hand-wound for maximum copper fill.
• Precision-balanced rotor will boost the efficiency and power performance of the motor.
• Nickel-plated sintered neodymium rotor for maximum motor acceleration, braking power and performance in high-temperature conditions.

Spec.:
Size: XK3674-1650KV
Poles: 4
KV: 1650
Max Current: 70A
Max Voltage: 33.6V/9S Lipo
Case Length: 74mm
Case Dia: 36mm
Shaft Dia: 5.0mm
Total Length: 91.2mm
Weight: 310g

TURNIGY XK motors are without question one of the best motors on the market today. It all starts in our very own factory where we install precision bearings, correctly rated magnets, balanced rotors, tool-steel shafts and stators that are wound by hand. We rigorously test each and every component at 14 critical points during construction, testing everything from materials all the way through to final performance tests.

Because we design and build these motors completely in-house we control the production and ensure product consistency from design right through to shipping. We removed the middle-man to bring you factory prices while not sacrificing quality or performance. 

Features:
• Hand-wound for maximum copper fill.
• Precision-balanced rotor will boost the efficiency and power performance of the motor.
• Nickel-plated sintered neodymium rotor for maximum motor acceleration, braking power and performance in high-temperature conditions.

Spec.:
Size: XK2845-3650KV
Poles: 4
KV: 3650
Max Current: 48A
Max Voltage: 16.8V/4S Lipo
Case Length: 46.5mm
Case Dia: 28mm
Shaft Dia: 3.175mm
Total Length: 60.5mm
Weight: 125g

Features:
• Hand-wound for maximum copper fill.
• Precision-balanced rotor will boost the efficiency and power performance of the motor.
• Nickel-plated sintered neodymium rotor for maximum motor acceleration, braking power, and performance in high-temperature conditions.

Specs:
Size: XK2845-1980KV
Poles: 4
KV: 1980
Max Power: 220W
Max Current: 24A
Max Voltage: 33V (2-4S LiPo)
Case Length: 46.5mm
Case Dia: 28mm
Shaft Dia: 3.175mm
Total Length: 60.5mm
Weight: 125g

Features:
• Hand-wound for maximum copper fill.
• Precision-balanced rotor will boost the efficiency and power performance of the motor.
• Nickel-plated sintered neodymium rotor for maximum motor acceleration, braking power, and performance in high-temperature conditions.

Spec.:
Size: XK2858-2900KV
Poles: 4
KV: 2900
Max Power: 1300W
Max Current: 58A
Max Voltage: 23V (6S LiPo)
Case Length: 58mm
Case Dia: 28mm
Shaft Dia: 3.175mm
Total Length: 70mm
Weight: 160g

TURNIGY XK motors are without question one of the best motors on the market today. It all starts in our very own factory where we install precision bearings, correctly rated magnets, balanced rotors, tool-steel shafts and stators that are wound by hand. We rigorously test each and every component at 14 critical points during construction, testing everything from materials all the way through to final performance tests.

TURNIGY XK motors are without question one of the best motors on the market today. It all starts in our very own factory where we install precision bearings, correctly rated magnets, balanced rotors, tool-steel shafts and stators that are wound by hand. We rigorously test each and every component at 14 critical points during construction, testing everything from materials all the way through to final performance tests.

Because we design and build these motors completely in-house we control the production and ensure product consistency from design right through to shipping. We removed the middle-man to bring you factory prices while not sacrificing quality or performance. 

TURNIGY XK motors are without question one of the best motors on the market today. It all starts in our very own factory where we install precision bearings, correctly rated magnets, balanced rotors, tool-steel shafts and stators that are wound by hand. We rigorously test each and every component at 14 critical points during construction, testing everything from materials all the way through to final performance tests.

This small lightweight 4ch switch is extremely handy for auxillary functions on all sorts of models. Plug the single lead into an auxillary switched function then switch your radio on, channel 1 on the electronic switch will then be active, cycle the auxillary switch once and channel 1 goes out and channel 2 comes on, cycle the switch once more and 2 goes out and channel 3 comes and so on until it comes back to channel 1. When the radio is switched off and then switched back on the unit will default to channel 1 each time. This unit is great for switching lights on and off and other low current applications.

Please note: For this switch to work correctly you will need to set the related channel travel to +- 100%.

Specs:
Input Voltage: 4.8~7.4v
Output Voltage: 4.8~7.4v
Maximum Current: 2amps
Length: 40mm
Width: 20mm
Height: 12mm
Weight: 7g
Input Cable: 21cm (JR type plug)

The Turnigy AquaStar Sensorless Brushless Motors offer outstanding performance for your boat at an incredible price!
 
Featuring a quality CNC machined billet T6 aluminum motor can, hand-wound high purity copper windings and powerful sintered neodymium magnet, you wont find a better priced motor of this caliber anywhere else!  It even features a billet aluminum water cooling jacket pre-installed.
 
The AquaStar brushless motors are a great choice for your deep-V, hydro or catamaran race boat and will be sure to leave the competition in your wake!
 
Features:               
• CNC Machined Billet T6 Aluminum Motor Can  
• High Purity Copper Windings
• 4mm Bullet Connectors Pre-installed    
• Powerful Sintered Neodymium Magnet    
• Precision Engineered for Maximum Energy Conversion
• Water Cooling Jacket Pre-installed
 
Specs:
RPM/v: 1050kv
Winding: 1.5Y
Max voltage: 22.2V (6S)
Max Current: 160A
Max Watts: 3100W
Resistance: 0.014ohm
No Load Current: 1.4A
Can Diameter: 39mm (actual motor diameter)
Can Diameter inc. Water Jacket: 49mm
Can Length: 84mm
Shaft Size: 5mm
Weight: 490g
Motor Connector: 4mm bullet plug

The Turnigy AquaStar Sensorless Brushless Motors offer outstanding performance for your boat at an incredible price!
 
Featuring a quality CNC machined billet T6 aluminum motor can, hand-wound high purity copper windings and powerful sintered neodymium magnet, you wont find a better priced motor of this caliber anywhere else!  It even features a billet aluminum water cooling jacket pre-installed.
 
The AquaStar brushless motors are a great choice for your deep-V, hydro or catamaran race boat and will be sure to leave the competition in your wake!
 
Features:               
• CNC Machined Billet T6 Aluminum Motor Can  
• High Purity Copper Windings
• 4mm Bullet Connectors Pre-installed    
• Powerful Sintered Neodymium Magnet    
• Precision Engineered for Maximum Energy Conversion
• Water Cooling Jacket Pre-installed
 
Specs:
RPM/v: 620kv
Winding: 2.5Y
Max voltage: 37V (10S)
Max Current: 105A
Max Watts: 3050W
Resistance: 0.03ohm
No Load Current: 0.7A
Can Diameter: 39mm (actual motor diameter)
Can Diameter inc. Water Jacket: 49mm
Can Length: 84mm
Shaft Size: 5mm
Weight: 508g
Motor Connector: 4mm bullet plug

Flex Shaft Set For Quanum Aquaholic Brushless Deep V Racing Boat.

Kit Includes:
1 x Threaded flex shaft
1 x Self lubricating PTFE sleeve
1 x Shaft spacer
1 x 2mm dog drive
1 x PTFE shaft gasket
1 x 7mm nyloc nut

Specs:
Flex Shaft Length: 310mm
Flex Shaft Diameter: 3mm
Weight: 20g (complete set)

Prop Shaft Support Set For Quanum Aquaholic / Relentless Racing Boats.

Kit Includes:
1 x Prop shaft support 
1 x Hull mount and bulkhead 
2 x Prop shaft bearing
1 x Bearing spacer
1 x Fixing set

Specs:
Weight: 21g
Dimensions(HxWxL): 57 x 35 x 54mm (assembled)
Shaft Size: 5mm
Material: Plastic

HydroPro Affinity RG65 Racing Yacht - "B" Sail Set, Main and Jib (Mylar Material 50 micron)

Specs:
Constant Current: 30A
Burst Current: 40A
Battery: 2-4S Lipoly / 5-12s NiXX
BEC: 5v / 2A
Motor Type: Sensorless Brushless
Cooling: Watercooled
Size: 70 x 27 x 17mm
Weight: 53g

Programming Functions:
Running Mode: Forward with brake / Forward and reverse with brake / Forward and reverse
Acceleration: 6% / 9% / 12%
Low Voltage Protection: None / 2.6V / 2.8V / 3.0V / 3.2V / 3.4V
Start Mode (Punch): Level 1 / Level 2 / Level 3 / Level 4 / Level 5 / Level 6 / Level 7 / Level 8 / Level 9
Reverse Force: 25% / 50% / 75% / 100%
Timing: 0° / 5° / 10° / 15° / 20° / 25° / 30° / Automatic

HobbyKing Boat ESC Programming Card

Programming Functions:
Running Mode: Forward with brake / Forward and reverse with brake / Forward and reverse
Acceleration: 6% / 9% / 12%
Low Voltage Protection: None / 2.6V / 2.8V / 3.0V / 3.2V / 3.4V
Start Mode (Punch): Level 1 / Level 2 / Level 3 / Level 4 / Level 5 / Level 6 / Level 7 / Level 8 / Level 9
Reverse Force: 25% / 50% / 75% / 100%
Timing: 0° / 5° / 10° / 15° / 20° / 25° / 30° / Automatic

Specs:
Constant Current: 90A
Burst Current: 120A
Battery: 2-6S Lipoly
BEC: 5.5v / 4A
Motor Type: Sensorless Brushless
Cooling: Watercooled
Size: 87 x 38 x 22mm
Weight: 105g

Programming Functions:
Running Mode: Forward with brake / Forward and reverse with brake / Forward and reverse
Acceleration: 6% / 9% / 12%
Low Voltage Protection: None / 2.6V / 2.8V / 3.0V / 3.2V / 3.4V
Start Mode (Punch): Level 1 / Level 2 / Level 3 / Level 4 / Level 5 / Level 6 / Level 7 / Level 8 / Level 9
Reverse Force: 25% / 50% / 75% / 100%
Timing: 0° / 5° / 10° / 15° / 20° / 25° / 30° / Automatic

Specs:
Constant Current: 50A
Burst Current: 70A
Battery: 2-6S Lipoly
BEC: 5.5v / 4A
Motor Type: Sensorless Brushless
Cooling: Watercooled
Size: 87 x 38 x 22mm
Weight: 105g

Programming Functions:
Running Mode: Forward with brake / Forward and reverse with brake / Forward and reverse
Acceleration: 6% / 9% / 12%
Low Voltage Protection: None / 2.6V / 2.8V / 3.0V / 3.2V / 3.4V
Start Mode (Punch): Level 1 / Level 2 / Level 3 / Level 4 / Level 5 / Level 6 / Level 7 / Level 8 / Level 9
Reverse Force: 25% / 50% / 75% / 100%
Timing: 0° / 5° / 10° / 15° / 20° / 25° / 30° / Automatic