Battery Accessories

Battery Velcro Strap (2pcs/bag)

Size: W13mm x L300mm

EC3 Male - Tamiya Female 

Turnigy Programmable Lipo Battery Warmer Bag - Lipo's can lose up to 40% of their capacity when used in cold weather. This of course will drastically shorten flight/drive times and of course performance. This superb Turnigy lipo warmer is perfect for the RC enthusiast who is flying/driving in cold weather/climate and also for competition pilots/drivers looking to squeeze every ounce of capacity from their battery for optimum performance, even in warm ambient temperatures.

You can select the desired temperature via the simple to operate buttons/LED display on the front of the bag, the inbuilt microprocessor offers a 7 step heater range from 25ºC ~ 45ºC (77ºF ~ 113ºF) and the sealable bag, which is lined with a heat reflective material, keeps your lipo snug and ready to use.

Specs:
Input Voltage: 10v ~ 13v DC
Idle Current: <30mAh
Working Current: 2A
Programmable Temp Value: 25/27.5/30/32.5/35/40/45ºC (2 button -/+ operation with LED display)
Operating Temp: -10ºC ~ 45ºC
Dimensions Overall: 295mm x 230mm
Dimensions Lipo Cavity: 195mm x 230mm
Weight: 135g
Connector: XT-60 + Croc Clip Lead (supplied)

The Turnigy Electrical Switch is a rugged solid state switch that has no contacts to fail like traditional mechanical switches. It can work on 4~8 NiMh/NiCD cells or a 2S 7.4V Lipoly battery. It features a Lipo mode which offers low voltage protection to the battery should the pack dip below 6.0V. A LED voltage indicator gives you at a glance status of your receiver so you always know how much of your pack is left. The plastic case has two tabs molded in allow you to mount it easily to your airframe for nice clean installations.

Features:
• Momentary on/off switch
• Screw mounting tabs
• Connectors work with JR/Futaba type servo plugs
• LED voltage indicator
• Lipo mode has voltage cutoff to protect lipoly batteries from over-discharge

Specs:
Input Voltage: 4.8~10V (2S Lipoly, or 4~8 cell NiMh/NiCD)
Continuous Current: 8A
Max Burst Current: 14A (10 sec)
Size: 43x33x9mm
Weight: 9g
Connectors: Futaba (Works with JR)

We've all done it before, you power up your model with a battery that you were certain was fully charged, but suddenly your model goes into LVC shortly after take-off, forcing you to make an emergency landing. It's very easy to lose track of which battery packs are charged and which aren't when you bring a box full of them to the field.

We now have a solution, the Turnigy Battery Charge Marker! This handy accessory sticks on to your battery pack with double sided tape and stays firmly in place. It features a sliding tab that simply and easily indicates whether or not your battery is charged. When you finish charging your pack, slide the tab to show the Green color (charged), when you take the battery out of your model after use, slide the tab to show the Red color (discharged). It's that simple!

Specs:
Dimensions: 25x12x3mm
Weight: 0.3g

10pcs/bag

Balance Lead Tidy/Saver 4S (4pcs)

Looking for a way of keeping balance leads tidy or out of your multirotor propellers then these little adapters will fit your needs. They come with double sided tape to stick them down.

There are different sizes depending on the cell count of your battery.

HXT-4mm Plug Harness for 2S Hardcase Saddle pack Lipoly Batteries

Discharge Plug: HXT-4mm
Battery Plugs: 4mm Bullet Connetor
Balance Plug: JST-XH

These balance lead protectors are the smart way to reduce the risk of damaging your lipo's balance lead during charging.   Simply snap them over the base of the balance lead and you have yourself a much larger and safer grip location for connecting and especially disconnecting from the balance port of your charger. Also great for adding a bit of protection from prop-chop on FPV racing drones.

Specs:
Color: Yellow
Size:  Suits 6S Lipoly packs

Includes:
One balance lead protector

The Boom Stopper will help stop short circuits from blowing your electronics up. Simply plug in the Boom Stopper between the power source, usually your battery, and the components you are wanting to power for the first time. If there is a problem the inline 2A fuse will blow, instead of your components. When the fuse is blown the LED will light up indicating there is a short circuit and the Boom Stopper will reduce the current to a level that won't immediately damage your electronics, giving you time to remove the power supply. 

XT150s are big 6mm sprung gold connectors that have a large contact area, making them great for high power applications up to 250A!

XT150s are big 6mm sprung gold connectors that have a large contact area, making them great for high power applications up to 250A!

The male connector uses a collet style spliced contact area to provide more surface to surface contact than standard gold connectors which use a thin mushroomed sheet as a spring.

The guys at Bat-Safe are RC enthusiasts and came up with a safe and awesome solution to store, transport, and most importantly charge your LiPo batteries.

This neat adapter is perfect for converting your balance plug to a 2 pin JST connector, ideal for connecting lights and other auxillary components.

This neat adapter is perfect for converting your balance plug to a 2 pin JST connector, ideal for connecting lights and other auxillary components.

This simple and effective charge lead comes pre-soldered with standard 4mm bullet connectors at the charger end and has stepped, bullet connectors at the battery end allowing you to charge hard case packs that utilise 4mm and 5mm connectors. 

This adapter will convert an HXT 5.5mm bullet equipped battery to an XT90 for use with an XT90 equipped ESC or an XT90 Charge lead.

This adapter will convert an XT90 equipped battery to an HXT 5.5mm bullet for use with an HXT 5.5mm bullet equipped ESC or an HXT 5.5mm bullet Charge lead.

A Parallel Harness is a common way to double the capacity rating (mAh) while keeping the same voltage.

The XT90 Parallel Adapters are the perfect solution for the modeler looking to increase battery capacity and reduce the weight of a model. The adapters also prevent adding additional lengths of cable, unlike most solutions. The parallel adapters are neatly soldered together and heat shrink shielded for a professional finish.

One end has a male EC3 connector and the other end has a female T connector.

One end has a female EC3 connector and the other end has a male T connector.

One end has male/female 5.5mm gold connectors and the other end has a female T connector.

One end has an EC5 female and the other end has a 5.5mm male/female connector.

Tamiya Female Harness w/Balance Lead for 2S Hardcase Lipo Battery

The perfect solution to connect 2 batteries with 4mm HXT connectors in series.

One end has an XT60 male connector and the other end has a female JST connector.

One end has a 4mm HXT male/female connector and the other has an XT60 female connector.

One end has an XT60 male connector and the other end has a 4mm HXT male/female connector.

T Connector Female Harness w/Balance Lead for 2S Hardcase Lipo Battery

4mm HXT Male/Female Harness w/Balance Lead for 2S Hardcase Lipo Battery.

One end has an XT60 male connector and the other end has a 3.5mm HXT male/female connector. This adapter allows you to use batteries with XT60 connectors to be used in the Walkera QR X350 drone.

Very neat short adapter with one end having a male T connector and the other having an XT60 female connector.