Batteries / Chargers

XT90 Battery Harness 10AWG for 2 Packs in Series

IMPORTANT: "These are not cheap copied XT90 plugs. These original Nylon XT90 plugs, manufactured by AMASS, can handle over 90A current for extended periods without exceeding 80DegC thanks to their better contact surface area. The plug is also less likely to deform or melt in comparison to copied non-Nylon XT90 plugs."

XT90 Battery Harness 10AWG for 2 Packs in Parallel

IMPORTANT: "These are not cheap copied XT90 plugs. These original Nylon XT90 plugs, manufactured by AMASS, can handle over 90A current for extended periods without exceeding 80DegC thanks to their better contact surface area. The plug is also less likely to deform or melt in comparison to copied non-Nylon XT90 plugs."

Power your compatible electrical items with the 4mm HXT to DC jack converter. The DC Jack converter has two 2mm jack plug connectors (positive centres) and is ideal for powering chargers or similar electrical items.

Specs:
Length: 210mm
DC Jack: 2mm
Battery Connector: 4mm HXT

1.3mm DC Power Plug to 2.1mm DC Power Socket Adapter (2pcs)

Specs:
Plug Internal Diameter: 1.3mm
Plug External Diameter: 3.5mm
Plug Length: 10mm
Socket Internal Pin: 2.1mm
Socket Internal Diameter: 5.5mm
Overall length: 160mm
Max rating: 1amp @ 12V
Quantity: 2pcs

Most standard 7S lithium polymer battery packs feature two balance ports, a 4S and 3S balance lead (total 7S). This makes it difficult to charge with most standard battery chargers that only feature one balance port.

With this super useful adapter you can easily charge your 7S battery with any standard 8~10S capable balance charger that accepts JST-XH balance plugs. This adapter takes the 4S and 3S individual plugs from your pack, and combines them to one single 7S balance plug which is able to connect to most standard 8~10S capable chargers.

Specs:
Input: 1 x 4S and 1 x 3S JST-XH balance plug
Output: 7S JST-XH balance plug
Length: 100mm

Most standard 6S lithium polymer battery packs feature two balance ports, 2 * 3S balance lead (total 6S). This makes it difficult to charge with most standard battery chargers that only feature one balance port.

With this super useful adapter you can easily charge your 6S battery with any standard 8~10S capable balance charger that accepts JST-XH balance plugs. This adapter takes the 2 * 3S individual plugs from your pack, and combines them to one single 6S balance plug which is able to connect to most standard 8~10S capable chargers.

Specs:
Input: 2 x 3S JST-XH balance plug
Output: 6S JST-XH balance plug
Length: 100mm

This is an all-in-one balance board adapter that allows you to balance charge 2~6S lipoly batteries with Thunder Power/Flight Power, Hyperion, JST-XH and JST-EH balance plugs. This makes it simple and eliminates the need for carrying separate balance adapters for each type of battery.

Specs;
Cell Count: 2~6S (7.4~22.2V)
Balance Connector Type: TP/HP/XH/EH

*Note: Can only be used to balance one type (TP/HP/XH/EH) at a time. Do not connect more than one type of balance leads to adapter board at same time or damage may occur.

JST-XH to JST LED Power Distribution Lead - A neat way to power LED's from 3s Lipoly's using the balance plug.



** WARNING: Check Polarity of your setup before connecting this harness.

This binding post set (1 Black, 1 Red) is ideal for building your own charging station or as a 12-24volt power access point for DC power applications.

They are designed to pass through wooden or metal facias up to 10mm thick (they are insulated and required a 7mm mounting hole). 

The output terminals have 4mm holes to suit 4mm male banana plugs, the terminal tips can be removed to allow aligator clamp access, the screw on terminal caps are insulated with a hard plastic shell.

Rated to around 50amps.

Spec:
Total length: 33mm
Depth: 10mm
Mounting hole: 7mm

HXT 4mm to T-Connector Battery Adapter Lead (2pc)

This adapter will convert an HXT 4mm equipped battery to a T-Connector for use with a T-Connector equipped ESC or Charge lead.

Spec:
Weight: 7g (Each)

This adapter will convert a 5.5mm Bullet Connector equipped battery to a T-Connector for use with a T-Connector equipped ESC or Charge lead.

Spec:
Weight: 9g(Each)

This adapter will convert a T-Connector equipped battery to an HXT 4mm for use with an HXT 4mm equipped ESC or Charge lead.

Spec:
Weight: 10g(Each)

This adapter will convert an HXT 4mm equipped battery to an XT60 for use with an XT60 equipped ESC or Charge lead.

Spec:
Weight: 10g(Each)

Mini T-connector charge lead with 4mm banana plugs.

Specs:
Weight: 15g
Lead Length: 300mm
Wire Gauge: 16AWG

A JST male plug to 2.54mm pitch male jumper lead for a variety of uses.

This lead is the best solution for batteries that are slightly out of balance; simply plug it into the individual cells on the balance lead, select a 1S charge rate and you can charge them one at a time to ensure they are all at optimum charge. 

Only use this method to restore cells that are slightly out of balance and remember that there could be something wrong with one of the cells so keep a close eye on it while charging.

Overall length: 70mm

Use this adapter to convert an XT-60 Charge lead for charging JST equiped batteries. 

HXT 4mm Connector to T-plug conversion charge lead

This will connect to a Lipo fitted with HXT 4mm connectors and a charge lead fitted with a T-plug

This simple and effective charge lead comes pre-soldered with standard 4mm bullet connectors at the charger end and has stepped, bullet connectors at the battery end allowing you to charge hard case packs that utilise 4mm and 5mm connectors. 

Use this adapter lead to charge batteries with 4MM Bullet Connector plugs, even those with reversed polarity Connectors using the supplied adaptors.

XT30 Male Connector w/24AWG Silicone Wire 55mm (1pc).

Suitable extension leads for Turnigy lipo batteries.

Suitable extension leads for Turnigy lipo batteries.

Suitable extension leads for Turnigy lipo batteries.

Suitable extension leads for Turnigy lipo batteries.

XT60 Male to 2 x DC Jack Plug Connectors 220mm (2pcs)

Specs:
Connector 1: XT60 Male
Connector 2: 2 x DC Jack Plug
Length: 220mm
Weight: 16.7g each
Quantity: 2pcs

XT30U Silicone Charge Lead with 4mm Banana Plugs.

XT60 Male w/12AWG 100mm Silicone Wire (5pcs).

An excellent, low resistance, flexible silicone charge lead with standard 4mm banana plugs on one end and a set of XT150/AS150 on the other. The Amass XT150/AS150 is a 7mm anti-spark connector rated at up to 150amps, and the 4mm banana plugs suits most chargers on the market today.

Specs:
Battery Connector: XT150/AS150 (7mm)
Charger Connection: 4mm Banana Plug
Wire Diameter: 14AWG
Wire: Tinned copper
Wire Insulation: Silicone rubber
Length: 300mm
Weight: 37.3g

Designed in-house by HobbyKing, this Turnigy parallel charge board can charge up to 6 LiPo or LiHV packs of the same capacity and cell count at the same time. The board is supplied with TRA connectors for the main charging leads, an XT60 lead to plug into the charger, and 2~6S JST-XH connectors for the balancing leads. The board is fused for protection and a 6S JST-XH adaptor lead is also supplied to connect the board to your charger balancing input.

Designed in-house by HobbyKing, this Turnigy parallel charge board can charge up to 6 LiPo or LiHV packs of the same capacity and cell count at the same time. The board is supplied with EC3 connectors for the main charging leads, an XT60 lead to plug into the charger, and 2~6S JST-XH connectors for the balancing leads. The board is fused for protection and a 6S JST-XH adaptor lead is also supplied to connect the board to your charger balancing input.

Designed in-house by HobbyKing, this Turnigy parallel charge board can charge up to 6 LiPo or LiHV packs of the same capacity and cell count at the same time. The board is supplied with EC5 connectors for the main charging leads, an XT60 lead to plug into the charger, and 2~6S JST-XH connectors for the balancing leads. The board is fused for protection and a 6S JST-XH adaptor lead is also supplied to connect the board to your charger balancing input.

Designed in-house by HobbyKing, this Turnigy parallel charge board can charge up to 6 LiPo or LiHV packs of the same capacity and cell count at the same time. The board is supplied with TR connectors for the main charging leads, a pair of 4mm banana plugs to connect to the charger, and 2~6S JST-XH connectors for the balancing leads. The board is fused for protection and a 6S JST-XH adaptor lead is also supplied to connect the board to your charger balancing input.