Batteries / Chargers

Protect your family and home from the hazard of lipo charging.
This lipo-guard is a fireproof bag, designed to stop and contain the fire caused by incorrectly or poorly functioning lipos, especially during charging.

We urge all customers to always practice extreme caution when charging and never leave a charging battery unattended.

This pack is the jumbo size. It is 25x33cm/10x13

The LP-Guard is made from a fibreglass woven fabric. Similar to fireproof suits worn by some firefighters.

Battery Velcro Strap (2pcs/bag)

Size: W13mm x L300mm

Simple to use Lipoly low voltage alarm that is small and light for on board use, plug's into balance lead for detecting low voltage on individual cells. A loud alarm will sound and LED will change from Green to Red if any individual cell drops to 3.3v or below.

Spec.
Lipoly Range: 2s~4s                              
Size: 38x25x11mm  
Weight: 7g
Voltage Accuracy: 0.03v
Low Voltage Alarm Threshold: 3.3v (per cell)

EC3 Male - Tamiya Female 

A precise balancer, discharger, and cell monitor. The Hobby King Battery Medic is a high-quality device for customers who want precision checking and balancing of their battery packs.
The unit can measure, discharge, and balance Lipoly packs up to 6S.

Spec.
Size: 93.5 x 60 x 17mm
Battery types: Li-polymer (2 ~ 6 cells)
Cell voltage range: 2.0v ~ 3.9v
Discharge: 3.0v ~ 4.2v
Bleed Current: 200~450mA

This is an original unit, calibrated at the factory.

HobbyKing®™ Fire Retardant LiPoly Battery Bag (170x45x50mm) (1pc)

These bags are made of super strong fire retardant fiberglass woven fabric and will stand very high temperatures for a reasonable period of time. The bags are stitched together with an extremely strong fire retardant thread and the flap is secured in place with hook and loop tape.

Ideal as a LiPoly charging bag, but superb for encasing your battery when it is installed on your model if the untoward ever happens.

Specs:
Material: Fire retardant fiberglass woven fabric
Length: 170mm
Width: 45mm
Height: 50mm
Weight: 52.5g

HobbyKing®™ Fire Retardant LiPoly Battery Bag (Flat) (230x140mm) (1pc)

These bags are made of super strong fire retardant fiberglass woven fabric and will stand very high temperatures for a reasonable period of time. The bags are stitched together with an extremely strong fire retardant thread and the flap is secured in place with hook and loop tape.

Ideal as a LiPoly charging bag.

Specs:
Material: Fire retardant fiberglass woven fabric
Length: 230mm
Width: 140mm
Height: Flat
Weight: 49.5g

Turnigy® Fire Retardant LiPoly Battery Bag (Zippered) (200x155x95mm) (1pc)

These bags are made of super strong fire retardant fiberglass woven fabric and will stand very high temperatures for a reasonable period of time. The bags are stitched together with an extremely strong fire-retardant thread and have a zippered lid.

Protect your family and home from the hazards of LiPo charging. This LP-Guard bag is a fireproof bag designed to stop and contain fires caused by incorrectly or poorly functioning LiPos, especially during charging.

We urge all customers to always practice extreme caution when charging and never leave a charging LiPo battery unattended.

This is a small bag at 18x23cm that can fit three 2200mah 3S1P LiPo packs comfortably.

The LP-Guard is made from a fiberglass woven fabric, that is similar to fireproof suits worn by some firefighters.

LiPoly batteries are a fantastic power source for all of our RC needs, but do need to be treated with respect due to their phenomenal energy density.

The golden rule when charging LiPoly packs is never to leave them unattended, but you can improve on this by using one of these fire retardant charging bags so that, should a mishap occur any conflagration will be contained within the bag and cannot impinge on surrounding surfaces.

These bags are made of super strong fire retardant fiberglass woven fabric and will stand very high temperatures for a reasonable period of time. The bags are stitched together with an extremely strong fire retardant thread and the flap is secured in place with hook and loop tape.

Features:
• Tough, fire retardant construction
• Large size for bigger packs
• Hook and Loop top fastenong
• Easy to store when not in use

Specs:
Material: Fire retardant fiberglass woven fabric
Length: 330mm
Width: 250mm
Weight: 135g

MultiStar Fire Retardant LiPoly Battery Bag (Flat) (210x165mm) (1pc)

These bags are made of super strong fire retardant fiberglass woven fabric and will stand very high temperatures for a reasonable period of time. The bags are stitched together with an extremely strong fire retardant thread and the flap is secured in place with hook and loop tape.

Ideal as a LiPoly charging bag.

Specs:
Material: Fire retardant fiberglass woven fabric
Length: 210mm
Width: 165mm
Height: Flat
Weight: 55g

Turnigy® Fire Retardant LiPoly Battery Bag (190x68x50mm) (1pc)

These bags are made of super strong fire retardant fiberglass woven fabric and will stand very high temperatures for a reasonable period of time. The bags are stitched together with an extremely strong fire retardant thread and the flap is secured in place with hook and loop tape.

Ideal as a LiPoly charging bag, but superb for encasing your battery when it is installed on your model if the untoward ever happens.

Specs:
Material: Fire retardant fiberglass woven fabric
Length: 190mm
Width: 68mm
Height: 50mm
Weight: 66.5g

Turnigy Programmable Lipo Battery Warmer Bag - Lipo's can lose up to 40% of their capacity when used in cold weather. This of course will drastically shorten flight/drive times and of course performance. This superb Turnigy lipo warmer is perfect for the RC enthusiast who is flying/driving in cold weather/climate and also for competition pilots/drivers looking to squeeze every ounce of capacity from their battery for optimum performance, even in warm ambient temperatures.

You can select the desired temperature via the simple to operate buttons/LED display on the front of the bag, the inbuilt microprocessor offers a 7 step heater range from 25ºC ~ 45ºC (77ºF ~ 113ºF) and the sealable bag, which is lined with a heat reflective material, keeps your lipo snug and ready to use.

Specs:
Input Voltage: 10v ~ 13v DC
Idle Current: <30mAh
Working Current: 2A
Programmable Temp Value: 25/27.5/30/32.5/35/40/45ºC (2 button -/+ operation with LED display)
Operating Temp: -10ºC ~ 45ºC
Dimensions Overall: 295mm x 230mm
Dimensions Lipo Cavity: 195mm x 230mm
Weight: 135g
Connector: XT-60 + Croc Clip Lead (supplied)

The Turnigy Electrical Switch is a rugged solid state switch that has no contacts to fail like traditional mechanical switches. It can work on 4~8 NiMh/NiCD cells or a 2S 7.4V Lipoly battery. It features a Lipo mode which offers low voltage protection to the battery should the pack dip below 6.0V. A LED voltage indicator gives you at a glance status of your receiver so you always know how much of your pack is left. The plastic case has two tabs molded in allow you to mount it easily to your airframe for nice clean installations.

Features:
• Momentary on/off switch
• Screw mounting tabs
• Connectors work with JR/Futaba type servo plugs
• LED voltage indicator
• Lipo mode has voltage cutoff to protect lipoly batteries from over-discharge

Specs:
Input Voltage: 4.8~10V (2S Lipoly, or 4~8 cell NiMh/NiCD)
Continuous Current: 8A
Max Burst Current: 14A (10 sec)
Size: 43x33x9mm
Weight: 9g
Connectors: Futaba (Works with JR)

We've all done it before, you power up your model with a battery that you were certain was fully charged, but suddenly your model goes into LVC shortly after take-off, forcing you to make an emergency landing. It's very easy to lose track of which battery packs are charged and which aren't when you bring a box full of them to the field.

We now have a solution, the Turnigy Battery Charge Marker! This handy accessory sticks on to your battery pack with double sided tape and stays firmly in place. It features a sliding tab that simply and easily indicates whether or not your battery is charged. When you finish charging your pack, slide the tab to show the Green color (charged), when you take the battery out of your model after use, slide the tab to show the Red color (discharged). It's that simple!

Specs:
Dimensions: 25x12x3mm
Weight: 0.3g

10pcs/bag

Balance Lead Tidy/Saver 4S (4pcs)

Looking for a way of keeping balance leads tidy or out of your multirotor propellers then these little adapters will fit your needs. They come with double sided tape to stick them down.

There are different sizes depending on the cell count of your battery.

These balance lead protectors are the smart way to reduce the risk of damaging your lipo's balance lead during charging.   Simply snap them over the base of the balance lead and you have yourself a much larger and safer grip location for connecting and especially disconnecting from the balance port of your charger. Also great for adding a bit of protection from prop-chop on FPV racing drones.

Specs:
Color: Yellow
Size:  Suits 6S Lipoly packs

Includes:
One balance lead protector

The Boom Stopper will help stop short circuits from blowing your electronics up. Simply plug in the Boom Stopper between the power source, usually your battery, and the components you are wanting to power for the first time. If there is a problem the inline 2A fuse will blow, instead of your components. When the fuse is blown the LED will light up indicating there is a short circuit and the Boom Stopper will reduce the current to a level that won't immediately damage your electronics, giving you time to remove the power supply. 

XT150s are big 6mm sprung gold connectors that have a large contact area, making them great for high power applications up to 250A!

XT150s are big 6mm sprung gold connectors that have a large contact area, making them great for high power applications up to 250A!

The male connector uses a collet style spliced contact area to provide more surface to surface contact than standard gold connectors which use a thin mushroomed sheet as a spring.

The guys at Bat-Safe are RC enthusiasts and came up with a safe and awesome solution to store, transport, and most importantly charge your LiPo batteries.

This neat adapter is perfect for converting your balance plug to a 2 pin JST connector, ideal for connecting lights and other auxillary components.

This neat adapter is perfect for converting your balance plug to a 2 pin JST connector, ideal for connecting lights and other auxillary components.

This simple and effective charge lead comes pre-soldered with standard 4mm bullet connectors at the charger end and has stepped, bullet connectors at the battery end allowing you to charge hard case packs that utilise 4mm and 5mm connectors. 

The ISDT BG-8S Smart Battery Checker is a new style of multipurpose battery checker. It is specifically designed for hobbyists of Remote Control products. It comes with lots of great features to help check your batteries, and receiver signals and even has a USB output that allows you to charge your phone or other devices. The Battery Checker has a 2.4” 320x240 display that can easily be seen in sunlight and has an easy-to-use menu system to show all functions and data.

These straps with the Graphene logo are a great addition for securing your batteries and other items, they are also great for mounting action cams, etc to your drones.

These strong and durable straps keep batteries safely and securely affixed to the model. The locking mechanism ensures that the strap doesn’t release at the wrong time, but can easily be undone to allow the battery or component to be removed.

Your friends will be green with envy thanks to our durable MultiStar Battery Straps. Designed using high-quality hook & loop to ensure your battery packs are held tight and secure on drones, planes, RC cars and more.

The Turnigy 8S Battery Capacity Meter checks the overall voltage of your battery packs (up to 8 cells) as well as the individual cell voltages. This is displayed on an easy
to read the LCD panel.

This adapter will convert an HXT 5.5mm bullet equipped battery to an XT90 for use with an XT90 equipped ESC or an XT90 Charge lead.

This adapter will convert an XT90 equipped battery to an HXT 5.5mm bullet for use with an HXT 5.5mm bullet equipped ESC or an HXT 5.5mm bullet Charge lead.

A Parallel Harness is a common way to double the capacity rating (mAh) while keeping the same voltage.

XT30 Male Connector w/24AWG Silicone Wire 55mm (1pc).

The XT90 Parallel Adapters are the perfect solution for the modeler looking to increase battery capacity and reduce the weight of a model. The adapters also prevent adding additional lengths of cable, unlike most solutions. The parallel adapters are neatly soldered together and heat shrink shielded for a professional finish.

We searched for a long time to find a battery strap that was strong yet didn't turn to fluff when used hundreds of times. The result is the TURNIGY battery strap, made from high-end polyester with nylon hooks. They won't break down and will continue to hold batteries firmly even after hundreds of uses.