Bargain Bin

Arduino MEGA ProtoShield V3 prototype expansion board (including the bread board)

This is the latest Arduino MEGA ProtoShield V3 prototype expansion board with Immersion Gold PCB processing technology. The motherboard gold square pad spacing is small and features SOP28 SMD component packaging, perfect for Arduino electronics enthusiasts. 

This board can not only seamlessly be plugged into the Arduino MEGA controller, components can be soldered directly. To complete a variety of circuits, this board features an integrated power indicator, status lights and reset buttons.

Specs:
Dimensions: 103x56x19mm
Weight: 39.7g (w/bread board)

*Note: This is not an original Arduino brand product.

The LM35 Linear Temperature Sensor Module can be used to detect ambient air temperature. This sensor offers a functional range between -40 degree Celsius to 150 degree Celsius. Sensitivity is 10mV per degree Celsius. The output voltage is proportional to the temperature. It is commonly used as a temperature measurement sensor. It includes thermocouples, platinum resistance, thermal resistance and temperature semiconductor chips, which are commonly used in high temperature measurement thermocouples. Platinum resistance temperature used in the measurement of 800 degrees Celsius, while the thermal resistance and semiconductor temperature sensor suitable for measuring the temperature of 100-200 degrees or below, in which the application of a simple semiconductor temperature sensor has good linearity and high sensitivity. The LM35 linear temperature sensor and sensor-specific expansion of Arduino board, in combination, can be very easy to achieve.

Specs:
Sensitivity: 10mV per degree
Celcius Functional range: -40 degree Celsius to 150 degree Celsius

*Note: This is not an original Arduino brand product.

Arduino 6-DOF IMU Module Attitude Control 6DOF 3205 345

*Note: This is not an original Arduino brand product.

Arduino 10DOF with ITG-3205, ADXL345, HMC5883L, and BMP085

*Note: This is not an original Arduino brand product.

The Arduino Relay module allows a wide range of microcontrollers such as Arduino, AVR ,PIC, ARM with digital outputs to control larger loads and devices like AC or DC Motors, electromagnets, solenoids, and incandescent light bulbs. This relay shield uses QIANJI JQC-3F high-quality relays with rated load 7A/240VAC,10A/125VAC,10A/28VDC. The relay output state is individually indicated by a light-emitting diode.

Specs:
Dimensions: 99x70x18mm
Weight: 88g

*Note: This is not an original Arduino brand product.

Keep your Telemetry Radios safe! These cases are made out of slightly translucent ABS plastic, so you still can see TX/RX LEDs. They have a very tight fit and finish and are clearly labeled. These cases will make your setup look like Pro gear, while keeping them safe!

Designed to fit FPV Radio Telemetry Kit - 915Mhz/433MHz(#42846/42847,not included), But fits other brand Telemetry Radios as well.

Includes:
3M Foam Double-tape X1
Ground module Case X1
Air module Case X1

Pulse / Heart Rate Sensor Module for Arduino

Specs:
Dimensions: 15 x 2mm
Weight: 2.66g

One of a series of four DIY robot car kits, these are great value and great fun for kids of all ages to put together.

You will only need some basic tools, some solder and a soldering iron and within a few hours you will have an operating robot car.

This model is activated by light sensor and will respond to a flashlight or other direct light source.

Includes:
1 x Light controlled robot car kit 

Note: This robot does not require programming.

One of a series of four DIY robot car kits, these are great value and great fun for kids of all ages to put together.

You will only need some basic tools, some solder and a soldering iron and within a few hours you will have an operating robot car.

This model is an obstacle avoider, with a sensor that detects objects to its front. 

Includes:
1 x Obstacle avoiding robot car kit 

Note: This robot does not require programming.

Make use of that free wind power electricity!

For use with the EK5100 Wind Turbine kit is this versatile charging unit.

Simply connect it up to your wind turbine and it can be used to charge your mobile phone, your ipod or your rechargable batteries. 

Includes:
Ek5400 Charger
Leads and cables

Make light and music with that free wind power electricity!

For use with the EK5100 Wind Turbine kit is this melody and light board.

Simply connect it up to your wind turbine and it can be used to power the sound and light board in various modes.

Includes:
Ek5300 Board
Instructions

3x30P Pin Socket - 2.54mm Pitch (5pcs/bag)

Perfect for DIY electronics projects.

This high quality switch is made in Taiwan and is proven to exceed more than 10000 switch cycles during testing.
This switch is designed for life time use.

Great for repairing your radio or making a swtich for your own project.

Spec.:
Style: 2-Way, Round Head
Dimension(LxWxD): 13x8x7mm(Plastic part only)
Length: 29mm(Switch & Mounting hole)
Mounting Hole Size: M6x8mm
Weight: 3.7g(Each)

30P Pin Header and Socket - 2.54mm Pitch (5 pcs)

Perfect for DIY electronic projects.

Molex 2.0 2Pin Cable Female Connector with 200mm x 24AWG Silicone Wire (5pcs)

Please note these are used in Nine Eagles equipment and the polarity is reversed.

Specs:
Connector: Molex 2.0 2pin
Colour: Black, Red
Length: 200mm

Molex 2.0 2Pin Female and Male Connectors (Plug and Crimp) (5sets)

Specs:
Connector: Molex 2.0 2pin Male and Female With Pins

JST-SH 3Pin Socket (Surface Mount) (5pcs)

Although this is a  surface mount socket it can also be used with thin extension wire leads. The soldered connections must be protected with heat shrink sleeving.

There are lots of applications for these sockets from using on robotic control boards to fixing connectors on flight controllers. They come in a number of different pin numbers.

Specs:
Type: Male
Number of Pins: 3
Pin Spacing: 1mm
Socket Size: 5.5x4.5x3.1mm

JST-SH 5Pin Socket (Surface Mount) (5pcs)

Although this is a  surface mount socket it can also be used with thin extension wire leads. The soldered connections must be protected with heat shrink sleeving.

There are lots of applications for these sockets from using on robotic control boards to fixing connectors on flight controllers. They come in a number of different pin numbers.

Specs:
Type: Male
Number of Pins: 5
Pin Spacing: 1mm
Socket Size: 7.5x4.5x3.1mm

JST-SH 6Pin Socket (Surface Mount) (5pcs)

Although this is a  surface mount socket it can also be used with thin extension wire leads. The soldered connections must be protected with heat shrink sleeving.

There are lots of applications for these sockets from using on robotic control boards to fixing connectors on flight controllers. They come in a number of different pin numbers.

Specs:
Type: Male
Number of Pins: 6
Pin Spacing: 1mm
Socket Size: 8.5x4.5x3.1mm

JST-SH 8Pin Socket (Surface Mount) (5pcs)

Although this is a  surface mount socket it can also be used with thin extension wire leads. The soldered connections must be protected with heat shrink sleeving.

There are lots of applications for these sockets from using on robotic control boards to fixing connectors on flight controllers. They come in a number of different pin numbers.

Specs:
Type: Male
Number of Pins: 8
Pin Spacing: 1mm
Socket Size: 10.5x4.5x3.1mm

JST-SH 4Pin Socket (Surface Mount) (5pcs)

Although this is a  surface mount socket it can also be used with thin extension wire leads. The soldered connections must be protected with heat shrink sleeving.

There are lots of applications for these sockets from using on robotic control boards to fixing connectors on flight controllers. They come in a number of different pin numbers.

Specs:
Type: Male
Number of Pins: 4
Pin Spacing: 1mm
Socket Size: 6.5x4.5x3.1mm

JST-SH 5Pin Female Plug with 200mm Wire Pigtail (5pcs)

JST-SH 5Pin Female (Plug and Crimp) (5pcs)

These plugs come with crimp style pins.

There are lots of applications for these plugs from using with robotic control boards to fixing plugs for flight controllers. They come in a number of different pin numbers.

Specs:
Type: Female
Number of Pins: 5
Pin Spacing: 1mm

JST-SH 8Pin Female (Plug and Crimp) (5pcs)

These plugs come with crimp style pins.

There are lots of applications for these plugs from using with robotic control boards to fixing plugs for flight controllers. They come in a number of different pin numbers.

Specs:
Type: Female
Number of Pins: 8
Pin Spacing: 1mm

The Grove indoor environment kit has been designed to make creating environmental applications intuitive and as simple as possible.

When used with the included Base Shield V2 as the Arduino breakout board, the kit allows you to plug in up to 11 different sensors and actuators to build a complete environment monitoring system customized to your own needs.

Regularly updated demo codes are provided on the Grove website (http://www.seeed.cc/projects.html?t=Grove) for a wide range of projects from a simple thermometer to hydroponic control systems. Adding additional sensors expand the possibilities even further. There is also a full tutorial section covering all aspects of the Grove kit.

A brilliant and practical introduction to the fascinating world of robotics and coding, perfect for inquisitive minds!

Features:
• Easy to understand kit
• Arduino compatible
• Online community support
• 11 Sensors/actuators included

Specs:
Base Shield:
Operating voltage: 3.5~5.5V
Dimensions 55 x 70mm

HV Relay:
Voltage: 250V
Current: 10A
Dimensions: 42 x 24 x 19.5mm
(Always consult a qualified electrician before working with high voltage applications)

Rotary Encoder:
Voltage: 4.5V~5.5V
Current: 10mA~30mA
Dimensions: 20 x 20mm
Weight: 12g

Piezo Buzzer:
Voltage: 4~8V
Sound Output: ≥85dB
Frequency: 2300Hz +/- 300Hz

Servo:
Voltage: 4.8~6V
Speed: 0.10sec/60° @ 6V
Torque: 1.8kg/cm @ 6V
Dimensions: 24 x 23 x 12mm
Weight: 8.5g

Included:
Base Shield V2
Momentary button
Piezo buzzer
Rotary encoder
Backlit LCD display
Light sensor
PIR motion sensor
Moisture sensor
High voltage relay
UV sensor
Servo
TH02 multi-function sensor