Bargain Bin

Spare Part - RC Adapter Multiplex for Scherrer Rx700LR Long Range UHF System

Rx700NR is a small and very light weight receiver with 9 channels that has a range of up to 20km! It also has an optimized input filter which will prevent interference from strong 2.4 GHz video systems.

The Rx700NR will work with any Scherrer long range transmitter and will provide you with a solid and safe signal for your flights. The antenna is mounted directly on the board and with a total weight of only 8 grams this receiver is perfect for UAVs where the focus is on weight and longer flight times.

Features:
• Up to 20km range
• External firmware upgrade port
• Running LED
• Completely new software
• Selectable PPM/PWM
• Sequential failsafe

Specs:
Board Dimensions: 26 x 53mm
Weight: 8g
Number of channels: 9
Output: PPM output 
Rssi output: 0.5 to 3.3V from min to mix
Supply voltage: 4 -10 V
Supply current RX: 18mA at 5V
System: Wideband frequency hopping 
Band: 433 and 440 MHz 
User firmware upgradeable: Yes
Wide user temperature range: -40C to +70C ambient

We all know the Mobius as the go-anywhere workhorse of action cameras, blazing the trail where other cameras fear to tread; but what do you do when the next mission looks tougher than usual?

Simple, stick your little buddy in a suit of armour with this tough, all alloy protective case!

Machined to allow easy access to all of the Mobius' many functions and maintaining a clear view from the lens, this case gives you peace of mind when you send your favourite action camera into the thick of it!

Features:
• Purpose made to fit the Mobius Action Camera
• Tough, all alloy design
• Access to all camera functions
• Bolt together case
• Lens shield

Specs:
Dimensions: 73 x 46 x 23mm
Weight: 40g

Quanum Exoskeleton for RunCam

Are you worried about your RunCam action camera not surviving a hard landing?  Simply give your RunCam a rigid exoskeleton frame.

Manufactured from super light weight alloy and machined to allow easy access to all of the RunCams many functions while maintaining a clear view from the lens, this frame gives you peace of mind when you send your favorite action camera into the thick of it!

Features:
• Purpose made to fit the RunCam Action Camera
• Tough, exoskeleton style design
• Superlight Alloy
• Access to all camera functions
• Bolt together case
• Lens shield

Specs:
Dimensions: 69 x 46 x 23mm
Weight: 21.5g

The HobbyKing® ™ GT2E is a affordable, 2-channel 2.4ghz ground radio, with adjustable steering dual-rate and servo reversing, making it a very simple setup for your car or boat. The automatic frequency hopping digital system provides a strong, reliable 2.4ghz signal, so rest assured you'll always be in control. Included in the package is a 3-channel mini receiver that will fit in most vehicles. The ergonomic feel of the trasnsmitter will feel good in your hands even after long track sessions.

Features:
• Reliable, interference free 2.4GHz AFHDS signal operation
• 2CH operation
• Use only 4xAA batteries for transmitter
• Adjustable steering dual-rate
• Simple binding procedure

Transmitter Specs:
RF Power: 20dBm (100mW) max
Modulation: GFSK
System Type: AFHDS 2A
Sensitivity: 1024
Low Voltage Warning: Yes
DSC Port: 3.5mm
Charge Port: Yes (3.5IN)
Power: 4xAA, 6VDC
Weight: 241g

Receiver Specs:
RF Receiver Sensitivity: -105dBm
Modulation: GFSK
System Type: AFHDS 2A
Sensitivity: 1024
Failsafe: Yes (Channel 2)
Power Port: Yes (VCC)
Power: 4.5~6.5 VDC 
Weight: 5g
Antenna Length: 26mm
Dimensions: 37x22x12mm

Includes:
HK-GT2E transmitter
HK-GT2E 3CH receiver
Antenna tube
Bind plug
User manual

When it comes to hardware, quality does matter! These titanium machine screws not only offer improved strength over steel, they are also much lighter in weight. These are ideal for use in performance models where shaving weight is absolutely critical, or for any project requiring high strength, lightweight hardware.

Spec.:
Size: M2 x 4mm
Weight: 0.11g(Each)

Why settle for only being able to charge your DJI Phantom 2 batteries at home?

The Quanum DC Field Charger charger allows you to quickly and easily charge your Phantom 2 batteries at the field from just about any 10~26VDC power source! This means easy battery charging from your car or truck's starter battery!

Simply connect the alligator clips to your vehicle's starter battery and the output lead to the Phantom 2 battery. The output lead features a polarity-protected plug which prevents improper connection. This charger provides up to 4A of current, matching that of the original DJI Phantom 2 battery charger.

The Orange OpenLRSng is an open-source receiver that can be programmed to use your choice of protocol and any channel in the 915MHz range. It is a fully user-customizable RF receiver that can even be programmed to utilize additional features such as telemetry, operative remote control via sticks (cPPM ready), and mission control.

The Turnigy TrackStar Sensored Brushless Motors offer outstanding performance at an incredible price!

Featuring a quality CNC alloy motor can, hand-wound high purity copper windings and powerful sintered neodymium magnets, you wont find a better priced motor of this caliber anywhere else! They also feature adjustable timing which allows for fine tuning the performance of your ride while the sensor ensures smooth startups and acceleration.

Once again we instructed our engineers to develop a motor that would not only rival but surpass the quality of the leading motors on the market today using the best quality magnets, bearings, and materials available.

The result is an outstanding series of motors that are efficient, strong, and robust enough for the most discerning modeler.

All of the SK3 series use quality double-shielded bearings, sintered neodymium magnets (the strongest type of permanent magnet commercially available), and a string wound stator to ensure accurate and consistent winding each and every time.

Performance Data (2S):

4x2: 24W, 3.35A, 131g static thrust
4x3: 31W, 4.4A, 180g static thrust
4.1x4.1: 40W, 5.7A, 235g static thrust

Once again we instructed our engineers to develop a motor that would not only rival but surpass the quality of the leading motors on the market today using the best quality magnets, bearings, and materials available.

The result is an outstanding series of motors that are efficient, strong, and robust enough for the most discerning modeler.

All of the SK3 series use quality double-shielded bearings, sintered neodymium magnets (the strongest type of permanent magnet commercially available), and a string wound stator to ensure accurate and consistent winding each and every time.

The Turnigy SK3 motors are suited to modelers who are seeking a top-quality brushless motor without compromise.

Performance Data (2S):
5.25x5.5: 48W, 6.7A, 323g static thrust
5.5x6.5: 62W, 8.5A, 412g static thrust
6x6: 74W, 10A, 466g static thrust

Performance Data (3S):
4.1x4.1: 58W, 5A, 284g static thrust
4.5x4.1: 74W, 7A, 363g static thrust
5x4.1: 100W, 9.5A, 472g static thrust

Turnigy SK3 brushless motors are yet another step forward in motor evolution.

Once again we instructed our engineers to develop a motor that would not only rival but surpass the quality of the leading motors on the market today using the best quality magnets, bearings, and materials available.

The result is an outstanding series of motors that are efficient, strong, and robust enough for the most discerning modeler.

All of the SK3 series use quality double-shielded bearings, sintered neodymium magnets (the strongest type of permanent magnet commercially available), and a string wound stator to ensure accurate and consistent winding each and every time.

The Turnigy SK3 motors are suited to modelers who are seeking a top-quality brushless motor without compromise.

Performance Data (2S):
12x8: 81W, 11A, 524g static thrust
13x10: 95W, 13A, 577g static thrust
14x10: 102W, 15A, 579g static thrust

Performance Data (3S):
11x3.8: 136W, 13A, 639g static thrust
11x5.5: 158W, 15A, 753g static thrust
11x7: 173W, 16A, 827g static thrust

Nitro Rumble - Engine Crankcase

Basher Nitro Circus MT - F/R steering kunckle arms

Dytac 20 Inch SPR Outer Barrel Assembly for Marui M4 (Silver)

Features:
• 20 inch SPR Outer Barrel Set 
• Aluminum construction barrel
• Comes with low profile gas block and gas tube
• Designed for Tokyo Marui M4/M16 AEG
• Silver color

Spec: 
Material: Aluminum
Color: Silver
Weight: 466g
Overall length: 505mm
Barrel threads: there is no thread on this barrel
Barrel Type: Rifle length
Based model: Tokyo Marui M4/M16 AEG
Manufacturer: Dytac

Package Includes:
1x 20 inch SPR Outer Barrel
1x Low profile gas block
1x Dummy Gas Tube

SkyZone have forged a reputation for quality and reliability in their products having been tested and developed by FPV pilots. The SKY-N2000 Transmitter packs a whopping 2000mW of ultra clean 5.8GHz power! A must for those looking for longer range and locked in video. The N2000 can transmit a full range of 32 channels and is supplied complete with all connecting cables.
   
The N2000 boasts some impressive features including remote channel switching, meaning the transmitting band and channel can be changed remotely with a 3 position switch on your radio. This function allows you to quickly change to a clear band and frequency should you encounter interference on your existing channel.

Features:
• 128 x 64 super bright color digital display with brightness & contrast control
• Channel and frequency display
• 2w of transmitting power
• 2Ch video input, remote channel switching
• Support 2-6S LiPoly battery
• Battery Voltage display
• Screen Display: Current / Temperature / PA Power detection

Specs:
Operating Voltage: 6.5 ~ 28V
Output Power: 27dbm, 30dbm, 33dbm
Antenna Connector: SMA Male
Supply Current @12v: 0.5A, 0.6A, 1A
Operating Temperature: -10 ~ +80 Degrees
Voltage Detection Accuracy: ±0.05v, ±0.1V, ±0.5V
Current Detection Accuracy: ±0.05A, ±0.06AV, ±0.2V
Video Band Width: 5MHz, 6MHz, 6MHz
Video Input Impedance: 75Ω/1Vp-p
Audio Input impedance: 6.5M Hz
Audio Sub-Carrier: 4.7KΩ
Dimensions: 60x35x20mm
Weight: 47g

Looking for the professional finish on your next quadcopter project? look no further! This simple and easy to install light module set, will not only provide you with a proffesional look but will also allow your quadcopter to be seen in any conditions with its super bright LEDs

The LED flash light set offers a wide voltage input range from 2-6s and is suitable for quadcopters up to 500mm diameter. 

Features:
• Suitable for quadcopters up to 500mm diameter
• Wide input voltage, 2-6s capability
• High efficiency frequency conversion circuit
• Low power consumption
• No flashing delay or brightness reduction
• High power output
• Simple frequency adjustment

Specs:
LED Cable Length: 500mm
System Weight: 48g
Input Voltage 7.4v ~ 22.2v

SWAT 41 inch Tactical Rifle Gun Bag (Kryptek Nomand)

Features:
• 1000D CORDURA Nylon Construction
• Two ways carrying method (Handheld / Shoulder)
• Padded loop protective edge
• Heavy Duty Zipper 
• Able to carry single rifle with length upto 41” inch
• Main Compartment (1020mm X 285mmX 70mm)
• Magazine Pouches (Inside the Bag) carry up to Five M4 / M16 / AK 5.56 /7.62 Type magazines
• Low profile zipper front pouch for tools and spare parts

Specs:
Weight: 1050g
Material: 1000D Nylon
Color/Pattern: Kryptek Nomand(KN)
Dimension: 1020mm X 285mm X 70mm
Manufacturer: SWAT

There's a lot to be said for the simple things in life, and with RC equipment becoming ever more flexible it's a refreshing change to find a simple, 4 channel radio that dispenses with the need for programming before you can use it.

The Turnigy TGY-i4X AFHDS/2A does exactly that and is a great entry level 4-channel telemetry 2.4ghz transmitter that can be switched between 1st and 2nd generation Automatic Frequency Hopping Digital System (AFHDS 2A) spread spectrum technology. The Turnigy TGY-i4X has a nice quality look and feel, while the programming is limited to one-switch V-tail/elevon mixing and servo reversing only. The transmitter is capable of being upgraded to up to 10 channels, see manual for details.

An ergonomically designed, ultra slim case design fits comfortably in your hands, an advantage during long flights. Digital trims and easy to read battery indicator LEDs give the TGY-i4X a modern feel with all the essential features you need. With a low profile antenna, the TGY-i4X is easy to transport and store. Adjustable length sticks, and a loop for attaching a neck strap round out the list of comfort features this radio offers.

The TGY-i4X comes with the TGY-i4X 4-channel receiver and is a superb budget radio for both new and experienced pilots alike!

Features:
• Entry level 4 channel 2.4ghz radio
• One switch V-tail/elevon mixer
• Easy to use servo reversing switches
• Standard Wing/Elevon/V-Tail
• Trainer port
• Simple LED battery indicator
• 1-Button binding

Transmitter Specs:
Channels: 4 (Expandable to 10)
Frequency: 2.40~2.48GHz
Bandwidth: 500KHz
DSC Port: PS2
Output: PPM Charger
Modulation: GFSK
Spread Spectrum Mode: AFHDS 2A and AFHDS
Band: 142 RF
Number of Frequency Channels: 20
Output Power: <=20dbm
Working Current: <=100mA
Working Voltage: 6V (4 x AA batteries)
Range: 100~300m
Dimensions: 174 x 89 x 190mm
Weight: 335g
Resolution: 1024 bit
Stick Mode: Mode 2 (Throttle Left)

Receiver Specs:
Channel: 4
Frequency: 2.40~2.48GHz
Power: 4.5V~6.6V/<30ma
Weight: 13g
Antenna length: 26mm
Dimensions: 45 x 23 x 9mm

Included:
Turnigy TGY-i4X transmitter
Turnigy TGY-i4X receiver
Bind plug
Manual

Requires:
4 x AA batteries

Instruction Manual is available under the "Files" tab.

Spare Part for Night Walrus - Main Wing

Spare Part for Night Walrus - Fuselage

Hobbyking 1875mm B-17 F/G Flying Fortress (V2) (Silver) - Replacement fuselage 1350mm (53.33in)

Hobbyking 1875mm B-17 F/G Flying Fortress (V2) (Silver) - Replacement Main Wing 1875mm(72.25in)

Hobbyking 1875mm B-17 F/G Flying Fortress (V2) (Silver) - Replacement Vertical Stabilizer

Hobbyking 1875mm B-17 F/G Flying Fortress (V2) (Silver) - Replacement Engine cowlings.

The FQ777-126 is the ultimate FPV hexacopter drone. This hexacopter drone is small and light enough to fit literally anywhere! In fact, it is so small it even fits and charges within a special compartment within the Transmitter making it small enough to fit into your pocket.

Not only does the Tx double up as a handy storage compartment, but it also charges the LiPo battery whilst on the move. The Spider mini hexacopter FQ777-126 drone is fitted with a 6 axis gyro making it stable and easy to fly indoors or outdoors when recording on your mini HD camera.

Replacement X axis stepping motor for Malyan M180 dual head 3D printer.

Turnigy high quality silicone wire is ideal for your RC project. It is super flexible and soft with a high strand count which means it is great for use in restrictive and compact areas. Available in a wide variety of gauges and colors to suit just about any application. 

The Rocket Surpass range of brushless motors is precision-made using the latest manufacturing processes. The heatsink can is CNC machined from a solid billet of 6061 T6 aluminum, high-purity copper is used for the windings for improved efficiency, and oversized bearings are used for durability. The stator has super thin (0.2mm) laminations, and the rotor is then precision balanced for reliability, and ultra-smooth running at maximum RPMs.

The Rocket Surpass range of brushless motors is precision-made using the latest manufacturing processes. The heatsink can is CNC machined from a solid billet of 6061 T6 aluminum, high-purity copper is used for the windings for improved efficiency, and oversized bearings are used for durability. The stator has super thin (0.2mm) laminations, and the rotor is then precision balanced for reliability, and ultra-smooth running at maximum RPMs.

The Rocket Surpass 4076-2025KV motor has been specially built for 1/8th scale monster trucks and truggies. This 4-pole, 12-slot high-torque motor is water and dust-proof and features a universal mounting system to fit just about all 1/8th-scale vehicles.

The Rocket Surpass range of brushless motors is precision-made using the latest manufacturing processes. The heatsink can is CNC machined from a solid billet of 6061 T6 aluminum, high-purity copper is used for the windings for improved efficiency, and double-shielded oversized bearings are used for durability. The motor includes sintered neodymium magnets, the stator has super thin (0.2mm) laminations, and the rotor is precision balanced for reliability, and ultra-smooth running at maximum RPMs.

The Rocket Surpass 5065-236KV motor suits sport, scale, and 3D-type models. This robust motor suits LiPo batteries up to 10S, on test with a 10S battery it produced an incredible 2000 watts of power at 57A, making it a great motor for the larger models. The motor is supplied with a machined prop adapter, complete with mounting bolts, allowing it to be mounted either way round.

The Rocket Surpass range of brushless motors is precision-made using the latest manufacturing processes. The heatsink can is CNC machined from a solid billet of 6061 T6 aluminum, high-purity copper is used for the windings for improved efficiency, and oversized ABEC5 high-speed bearings are used for durability. The stator has super thin (0.35mm) laminations, and the rotor is then precision balanced for reliability and ultra-smooth running at maximum RPMs.

The Rocket Surpass KK2845-5900KV motor has been specially built for 1/12~14th size RC cars and trucks and is totally waterproof for use in extreme conditions. This powerful 4-pole, 12-slot motor features a universal mounting system so that it will fit just about all 1/12~14th scale vehicles.

The Rocket Surpass range of brushless motors is precision-made using the latest manufacturing processes. The heatsink can is CNC machined from a solid billet of 6061 T6 aluminum, high-purity copper is used for the windings for improved efficiency, and oversized ABEC5 high-speed bearings are used for durability. The stator has super thin (0.35mm) laminations, and the rotor is then precision balanced for reliability and ultra-smooth running at maximum RPMs.

The Rocket Surpass 3650-5400KV motor has been specially built for 1/10th size RC cars and trucks and is water and dust-resistant for use in demanding conditions. This powerful 4-pole, 12-slot motor features a universal mounting system so that it will fit just about all 1/10th scale vehicles.

The Rocket Surpass range of brushless motors is precision-made using the latest manufacturing processes. The heatsink can is CNC machined from a solid billet of 6061 T6 aluminum, high-purity copper is used for the windings for improved efficiency, and oversized ABEC5 high-speed bearings are used for durability. The stator has super thin (0.35mm) laminations, and the rotor is then precision balanced for reliability and ultra-smooth running at maximum RPMs.

The Rocket Surpass 3660-4500KV motor has been specially built for 1/10th size RC cars and trucks and is water and dust-resistant for use in demanding conditions. This powerful 3T, 4-pole, 12-slot motor features a universal mounting system so that it will fit just about all 1/10th scale vehicles.