Hardware & Accessories

EC2 Female & Male (5pcs/bag)

This is an all-in-one balance board adapter that allows you to balance charge 2~6S lipoly batteries with Thunder Power/Flight Power, Hyperion, JST-XH and JST-EH balance plugs. This makes it simple and eliminates the need for carrying separate balance adapters for each type of battery.

Specs;
Cell Count: 2~6S (7.4~22.2V)
Balance Connector Type: TP/HP/XH/EH

*Note: Can only be used to balance one type (TP/HP/XH/EH) at a time. Do not connect more than one type of balance leads to adapter board at same time or damage may occur.

JST-XH to JST LED Power Distribution Lead - A neat way to power LED's from 3s Lipoly's using the balance plug.



** WARNING: Check Polarity of your setup before connecting this harness.

60mm Molex 1.25 Servo Extension (5pcs/bag)

Spec.
Weight: 0.6g(Each)

120mm Molex 1.25 Servo Extension (5pcs/bag)

Spec.
Weight: 0.8g(Each)

120mm JST-SH1.0 Servo extension (5pcs/bag)

Spec.
Weight: 0.7g(Each)

This handy connector set will be appreciated by anyone who is dealing with 'Header Pins' on Multirotor boards or any othe type of PCB.

This set consists of a 1 pin housing and 1 female terminal.

8mm Gold Connectors and housing set.

Rated to around 170A
Excellent for high voltage/ high current systems.

Includes:
2 male connectors, 2 femal connectors and 2 housings

Weight: 23g

120mm Male to Male Jumper Cable Set (10pc)

Specs: 
Length: 120mm
Pin Spacing: 1mm

Molex 2 Pin Cable Female Connector with 220mm x 26AWG Wire

Specs:
Connector: Molex 2 Pin
Colour: Black, Red
Length: 220mm

Molex 3 Cable Female Connector with 230mm x 26AWG Wire.  

Specs:
Connector:  Female Molex 3 pin
Colour: Black, Yellow, White
Length: 230mm

4mm Gold Plated Banana Plug (10pc)

105mm Female Molex 1.25 to Twin Male JST-SH 1.0mm Y Lead

JR Male to 2 x JST(Molex) Female 1.00mm (1pc)

This lead converts 2 x JST(Molex) 1.00mm pitch plugged devices to 1 x JR type male plug.

Specs:
Female Plug: 2 x JST(Molex) 1.00mm pitch
Male Plug: JR type
Length Overall: 123mm
Length Each Tail: 46mm

Micro JST(Molex) 1.0mm Pitch Y Lead (1pc)

Y lead for 2 x micro JST(Molex) plugged servo's or ESC.

Specs:
Male Plug: 2 x JST(Molex) 1.00mm pitch
Female Plug: 1 x JST(Molex) 1.00mm pitch
Length Overall: 105mm
Length Each Tail: 43mm

Mini black T Connector pack (5 Pairs)

Specs:
Base Dimensions: 5mm x 8mm
Contact Dimension: 3mm x 5mm x 1mm
Rating: 10amps continuous

Super flexible 26AWG twisted silicone male to male servo lead. These are specifically made as signal leads for RX to Flight controller connections, the light 26AWG silicone wire is so flexible it transfers virtually no vibration to the Flight controller, well the twist helps reduce inducted noise. If used in conjunction of having only one lead vertical and the other leads turned on their side for signal only, makes for a clean and minimal vibration transfer installation. Or better yet a single CPPM/SBUS single lead. 

Specs:
Length: 130mm(black/red/white)
Connection: Male JR style plug on each end.

Super flexible 26AWG twisted silicone male to male servo lead. These are specifically made as signal leads for RX to Flight controller connections, the light 26AWG silicone wire is so flexible it transfers virtually no vibration to the Flight controller, well the twist helps reduce inducted noise. If used in conjunction of having only one lead vertical and the leads turned on their side for signal only makes for a clean and minimal vibration transfer installation, or better yet a single CPPM/SBUS single lead.

Specs:
Length: 80mm(black/red/white)
Connection: Male JR style plug on each end.

A handy adapter to convert an XT60 equipped battery to an MPX style connector. Useful for use with MPX equipped ESC or Charge leads.

Spec:
Weight: 5.3g(Each)

A JST male plug to 2.54mm pitch male jumper lead for a variety of uses.

This lead is the best solution for batteries that are slightly out of balance; simply plug it into the individual cells on the balance lead, select a 1S charge rate and you can charge them one at a time to ensure they are all at optimum charge. 

Only use this method to restore cells that are slightly out of balance and remember that there could be something wrong with one of the cells so keep a close eye on it while charging.

Overall length: 70mm

This is a great way to avoid power shorts.

Gold connectors on their own are notorious for creating a short circuit and looking messy. Use these to keep your connections safe and looking neat!

Rated to 20Amp these connectors are an excellent replacement for JST plugs on todays small yet high C rated batteries.

Micro Servo Connector Lead 1.25 Pitch - Female Connector (5pcs/bag)

Spec.
Length: 70mm
Plug Type: 1.25 Pitch Micro

Nylon Spinner w/ Accessories
Adapter rings supplied to accept a variety of shaft sizes.

Nylon Spinner w/ Accessories
Adapter rings supplied to accept a variety of shaft sizes.

Nylon Spinner w/ Accessories
Adapter rings supplied to accept a variety of shaft sizes.

Nylon Spinner w/ Accessories
Adapter rings supplied to accept a variety of shaft sizes.

Spinner for folding Prop (Small)
Collet style, will fit 2.3~2.5mm motor shafts
Prop shaft bolt is 5mm
Requires a propeller to suit 5mm shafts.
Weight: 9g
Diameter: 31mm

Very well formed, light weight and firm, foam wheels.

Control Arms 43x13x24x3mm (5pcs/bag)

Nylon Y-Joint (5pcs/bag)

size:D4xΦ2xL23mm