$2 - $4.99

5mm Male Gold Plated Spring Connector - Low Profile (10pcs)

Pro Tip: If you find the bullets hard to plug in to your battery, take a set of needle nose pliers and gently squeeze two of the six prongs, turn the plug and repeat on the other four prongs. If the plug is too loose take a small Phillips head screw driver and gently force the prongs open a little until you have a snug fit.

Keeping the motor, ESC and battery pack cool can often be a challenge, particularly in the efficient, streamlined models we all love to fly. Turnigy have come up with a great and easy to fit solution; why not let the air in where it's most needed - right at the front!

This range of Turnigy Turbo Spinners have been designed from the outset to allow a high volume of cooling air in via the slots in the tough nylon front molding. This then passes into the motor area through the large holes in the turned aluminum backplate for maximum cooling.
No holes, air scoops or exposed components to spoil the look of your latest pride and joy!   

A stylish and highly practical solution for a wide range of model types and sizes, these Turnigy Turbo Spinners are as easy on the pocket as they are on the eye!

 
Features:
• Integrated cooling channels
• Turned aluminum backplate
• High quality construction
• Easy and fast to fit


 
Specs:
Diameter: 51mm
Overall length: 48mm
Center hole: 6mm
Construction: Aluminum/Nylon
Weight: 20g

Keeping the motor, ESC and battery pack cool can often be a challenge, particularly in the efficient, streamlined models we all love to fly. Turnigy have come up with a great and easy to fit solution; why not let the air in where it's most needed - right at the front!

This range of Turnigy Turbo Spinners have been designed from the outset to allow a high volume of cooling air in via the slots in the tough nylon front molding. This then passes into the motor area through the large holes in the turned aluminum backplate for maximum cooling.
No holes, air scoops or exposed components to spoil the look of your latest pride and joy!    

A stylish and highly practical solution for a wide range of model types and sizes, these Turnigy Turbo Spinners are as easy on the pocket as they are on the eye!

 
Features:
• Integrated cooling channels
• Turned aluminum backplate
• High quality construction
• Easy and fast to fit


 
Specs:
Diameter: 63mm
Overall length: 60mm
Center hole: 8mm
Construction: Aluminum/Nylon
Weight: 26g

Keeping the motor, ESC and battery pack cool can often be a challenge, particularly in the efficient, streamlined models we all love to fly. Turnigy have come up with a great and easy to fit solution; why not let the air in where it's most needed - right at the front!

This range of Turnigy Turbo Spinners have been designed from the outset to allow a high volume of cooling air in via the slots in the tough nylon front molding. This then passes into the motor area through the large holes in the turned aluminum backplate for maximum cooling.
No holes, air scoops or exposed components to spoil the look of your latest pride and joy!    

A stylish and highly practical solution for a wide range of model types and sizes, these Turnigy Turbo Spinners are as easy on the pocket as they are on the eye!

 
Features:
• Integrated cooling channels
• Turned aluminum backplate
• High quality construction
• Easy and fast to fit


 
Specs:
Diameter: 75mm
Overall length: 68mm
Center hole: 8mm
Construction: Aluminum/Nylon
Weight: 43g

Keeping the motor, ESC and battery pack cool can often be a challenge, particularly in the efficient, streamlined models we all love to fly. Turnigy have come up with a great and easy to fit solution; why not let the air in where it's most needed - right at the front!

This range of Turnigy Turbo Spinners have been designed from the outset to allow a high volume of cooling air in via the slots in the tough nylon front molding. This then passes into the motor area through the large holes in the turned aluminum backplate for maximum cooling.
No holes, air scoops or exposed components to spoil the look of your latest pride and joy!    

A stylish and highly practical solution for a wide range of model types and sizes, these Turnigy Turbo Spinners are as easy on the pocket as they are on the eye!

 
Features:
• Integrated cooling channels
• Turned aluminum backplate
• High quality construction
• Easy and fast to fit


 
Specs:
Diameter: 75mm
Overall length: 68mm
Center hole: 8mm
Construction: Aluminum/Nylon
Weight: 43g

Just because you may have outgrown your Legos and Erector sets does not mean the fun has to stop. Introducing RotorBits, the modular construction set of endless possibilities. Based on the idea of standardized connections and dimensions, the only limit to what can be built is your imagination.

RotorBits can be recycled and reused into other creations, mix and matching different bits to make a Y6 or Bi-Rotor! As your collection of Bits grows and concepts evolve with plug & play easy, who knows what you can come up with? Have club competitions for creative ideas or races for fastest box to air builds. RotorBits is one idea that can never be outdated only reconfigured.

The Quad plate has 4 10x10mm slots for motor arms and 45x45mm posts for flight controller mounting. The center plate as other provisions for mounting other Bits and holes at 10mm intervals.

Specs:
Size: 100x100mm
Weight: 77g
Color: Green

Turnigy high quality silicone wire is ideal for your RC project. It is super flexible and soft with a high strand count which means it is great for use in restrictive and compact areas. Available in a wide variety of gauges and colors to suit just about any application.

Features:
• Super flexible
• High strand count
• Pure silicone outer

Specs:
Diameter: 12AWG
Length: 1m
Temperature Rating: 200°C
Inner Core: Multi-strand
Outer Sheath: Pure silicone
Color: Red

*This item is only available as 1m lengths, if you wish to purchase longer continuous lengths use R12A1062-06

Turnigy high quality silicone wire is ideal for your RC project. It is super flexible and soft with a high strand count which means it is great for use in restrictive and compact areas. Available in a wide variety of gauges and colors to suit just about any application.

Features:
• Super flexible
• High strand count
• Pure silicone outer

Specs:
Diameter: 10AWG
Length: 1m
Temperature Rating: 200°C
Inner Core: Multi-strand
Outer Sheath: Pure silicone
Color: Red

Alloy Prop Saver & Adapter w/ Band
Weight: 2.5g

Please select below for your size;
Available: 4mm

High quality carbon fiber round tube that can be used for many applications or custom projects.

Specs:
Length: 330mm
Outer diameter: 16mm
Inner diameter: 14mm

USBtinyISP V2.0 (Arduino-Compatible) is an ISP downloader for AVR microcontrollers based on the USB interface. It can be used for most AVR microcontrollers to download programs. In Arduino IDE, USBtinyISP is a downloader that is supported at all times, making it simple and convenient to use.

Specs:
Dimensions: 49x48x12mm
Weight: 17.3g

*Note: This is not an original Arduino brand product.

This is a great “bread board” pin ready accelerometer for your Arduino or other microcontroller projects

Features:
• BMA180 three-axis ultra-high performance digital accelerometer, which provides a 14-bit digital output via a 4-wire SPI or 2-wire I 2 C interface
• Full scale measurement range can be set to ± 1g balance, 1.5G, 2G, 3G, 4G, 8G or 16G
• programmable wake-up
• Low-g and high-g detection
• Tap detection
• Slope detection
• Self-test capability
• The sensor also has two operating modes: low noise, low power consumption in a tiny 3x3mm 12-pin LGA package BMA180
• The sensor can be between 1.62 to 3.6V VDD and 1.2 to 3.6V VDDIO supply will typically only consume 650uA standard mode.

Specs:
Size: 21 x 10 x 2.6mm
Voltage: 1.2-3.6v
Output: SPI or I2C

*Note: This is not an original Arduino brand product.

Superheterodyne 3310 Wireless receiver module +315RF Wireless transmitter module 

Arduino MEGA ProtoShield V3 prototype expansion board (including the bread board)

This is the latest Arduino MEGA ProtoShield V3 prototype expansion board with Immersion Gold PCB processing technology. The motherboard gold square pad spacing is small and features SOP28 SMD component packaging, perfect for Arduino electronics enthusiasts. 

This board can not only seamlessly be plugged into the Arduino MEGA controller, components can be soldered directly. To complete a variety of circuits, this board features an integrated power indicator, status lights and reset buttons.

Specs:
Dimensions: 103x56x19mm
Weight: 39.7g (w/bread board)

*Note: This is not an original Arduino brand product.

Keep your Telemetry Radios safe! These cases are made out of slightly translucent ABS plastic, so you still can see TX/RX LEDs. They have a very tight fit and finish and are clearly labeled. These cases will make your setup look like Pro gear, while keeping them safe!

Designed to fit FPV Radio Telemetry Kit - 915Mhz/433MHz(#42846/42847,not included), But fits other brand Telemetry Radios as well.

Includes:
3M Foam Double-tape X1
Ground module Case X1
Air module Case X1

Replacement Rear Crankshaft Bearing for NGH GT35 and GT35R Gas Engines.

NGH GT25/GF38 Gas Engines Replacement Crankshaft Front Bearing

Specs:
Outlet Diameter: 26mm
Inner Diameter: 10mm
Width: 8mm
Type: Sealed

Carbon fiber tail wheel brackets add good looks, strength, and most importantly, keep excess weight out of the tail of your airplane. Made from 3K Carbon cloth, these brackets are light and strong. Comes un-drilled so it can suit a wide variety of models. Drill dimple marks are molded in for easy drilling.

Suited for models up to 80cc sized models.

Specs:
Length: 118mm
Width: 14.2mm
Weight: 7.5g

Carbon fiber tail wheel brackets add good looks, strength, and most importantly, keep excess weight out of the tail of your airplane. Made from 3K Carbon cloth, these brackets are light and strong. Comes un-drilled so it can suit a wide variety of models. Drill dimple marks are molded in for easy drilling.

Suited for models up to 120cc sized models.

Specs:
Length: 170mm
Width: 12mm
Weight: 9g

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 10g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 10g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

Turnigy high quality silicone wire is ideal for your RC project. It is super flexible and soft with a high strand count which means it is great for use in restrictive and compact areas. Available in a wide variety of gauges and colors to suit just about any application.

Features:
• Super flexible
• High strand count
• Pure silicone outer

Specs:
Diameter: 8AWG
Length: 1m
Temperature Rating: 200°C
Inner Core: Multi-strand
Outer Sheath: Pure silicone
Color: Red

The wheel has a strong brushed finish alloy hub which is made from 1 piece lathed aluminium. The rubber appears to be of excellent quality and has an increasing resistance when compressed as it has a foam insert for cuishioning.

These are an excellent looking wheel and will last long enough for you to pass them on to your grandchildren.

Excellent quality and a solid light weight design.

Diameter : 1.75 

Quanum Skull Crusher 2WD - Drive Shaft/CVJ

A2032 and A2033 33434 CVD

Clutch Gears 14T - A3015

Full Alloy Metal Steering Knuckle Arms L/R - A2038 & A3015 (1pair)

This is a great way to avoid power shorts.
Rated to around 120A

Gold connectors on their own are notorious for creating a short circuit and looking messy. Use these to keep your connections safe and looking neat!
 
Easier to solder and a stronger connection than Deans T-plugs

This is an all-in-one balance board adapter that allows you to balance charge 2~6S lipoly batteries with Thunder Power/Flight Power, Hyperion, JST-XH and JST-EH balance plugs. This makes it simple and eliminates the need for carrying separate balance adapters for each type of battery.

Specs;
Cell Count: 2~6S (7.4~22.2V)
Balance Connector Type: TP/HP/XH/EH

*Note: Can only be used to balance one type (TP/HP/XH/EH) at a time. Do not connect more than one type of balance leads to adapter board at same time or damage may occur.

120mm JST-SH1.0 Servo extension (5pcs/bag)

Spec.
Weight: 0.7g(Each)

8mm Gold Connectors and housing set.

Rated to around 170A
Excellent for high voltage/ high current systems.

Includes:
2 male connectors, 2 femal connectors and 2 housings

Weight: 23g

4mm Gold Plated Banana Plug (10pc)

This adapter will convert a 5.5mm Bullet Connector equipped battery to a T-Connector for use with a T-Connector equipped ESC or Charge lead.

Spec:
Weight: 9g(Each)

Mini black T Connector pack (5 Pairs)

Specs:
Base Dimensions: 5mm x 8mm
Contact Dimension: 3mm x 5mm x 1mm
Rating: 10amps continuous