Bargain Bin

Superheterodyne 3310 Wireless receiver module +315RF Wireless transmitter module 

Arduino MEGA ProtoShield V3 prototype expansion board (including the bread board)

This is the latest Arduino MEGA ProtoShield V3 prototype expansion board with Immersion Gold PCB processing technology. The motherboard gold square pad spacing is small and features SOP28 SMD component packaging, perfect for Arduino electronics enthusiasts. 

This board can not only seamlessly be plugged into the Arduino MEGA controller, components can be soldered directly. To complete a variety of circuits, this board features an integrated power indicator, status lights and reset buttons.

Specs:
Dimensions: 103x56x19mm
Weight: 39.7g (w/bread board)

*Note: This is not an original Arduino brand product.

Keep your Telemetry Radios safe! These cases are made out of slightly translucent ABS plastic, so you still can see TX/RX LEDs. They have a very tight fit and finish and are clearly labeled. These cases will make your setup look like Pro gear, while keeping them safe!

Designed to fit FPV Radio Telemetry Kit - 915Mhz/433MHz(#42846/42847,not included), But fits other brand Telemetry Radios as well.

Includes:
3M Foam Double-tape X1
Ground module Case X1
Air module Case X1

Replacement Rear Crankshaft Bearing for NGH GT35 and GT35R Gas Engines.

NGH GT25/GF38 Gas Engines Replacement Crankshaft Front Bearing

Specs:
Outlet Diameter: 26mm
Inner Diameter: 10mm
Width: 8mm
Type: Sealed

Carbon fiber tail wheel brackets add good looks, strength, and most importantly, keep excess weight out of the tail of your airplane. Made from 3K Carbon cloth, these brackets are light and strong. Comes un-drilled so it can suit a wide variety of models. Drill dimple marks are molded in for easy drilling.

Suited for models up to 80cc sized models.

Specs:
Length: 118mm
Width: 14.2mm
Weight: 7.5g

Carbon fiber tail wheel brackets add good looks, strength, and most importantly, keep excess weight out of the tail of your airplane. Made from 3K Carbon cloth, these brackets are light and strong. Comes un-drilled so it can suit a wide variety of models. Drill dimple marks are molded in for easy drilling.

Suited for models up to 120cc sized models.

Specs:
Length: 170mm
Width: 12mm
Weight: 9g

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 10g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 10g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

Turnigy high quality silicone wire is ideal for your RC project. It is super flexible and soft with a high strand count which means it is great for use in restrictive and compact areas. Available in a wide variety of gauges and colors to suit just about any application.

Features:
• Super flexible
• High strand count
• Pure silicone outer

Specs:
Diameter: 8AWG
Length: 1m
Temperature Rating: 200°C
Inner Core: Multi-strand
Outer Sheath: Pure silicone
Color: Red

The wheel has a strong brushed finish alloy hub which is made from 1 piece lathed aluminium. The rubber appears to be of excellent quality and has an increasing resistance when compressed as it has a foam insert for cuishioning.

These are an excellent looking wheel and will last long enough for you to pass them on to your grandchildren.

Excellent quality and a solid light weight design.

Diameter : 1.75 

Quanum Skull Crusher 2WD - Drive Shaft/CVJ

A2032 and A2033 33434 CVD

Clutch Gears 14T - A3015

Full Alloy Metal Steering Knuckle Arms L/R - A2038 & A3015 (1pair)

This is a great way to avoid power shorts.
Rated to around 120A

Gold connectors on their own are notorious for creating a short circuit and looking messy. Use these to keep your connections safe and looking neat!
 
Easier to solder and a stronger connection than Deans T-plugs

This is an all-in-one balance board adapter that allows you to balance charge 2~6S lipoly batteries with Thunder Power/Flight Power, Hyperion, JST-XH and JST-EH balance plugs. This makes it simple and eliminates the need for carrying separate balance adapters for each type of battery.

Specs;
Cell Count: 2~6S (7.4~22.2V)
Balance Connector Type: TP/HP/XH/EH

*Note: Can only be used to balance one type (TP/HP/XH/EH) at a time. Do not connect more than one type of balance leads to adapter board at same time or damage may occur.

120mm JST-SH1.0 Servo extension (5pcs/bag)

Spec.
Weight: 0.7g(Each)

8mm Gold Connectors and housing set.

Rated to around 170A
Excellent for high voltage/ high current systems.

Includes:
2 male connectors, 2 femal connectors and 2 housings

Weight: 23g

4mm Gold Plated Banana Plug (10pc)

This adapter will convert a 5.5mm Bullet Connector equipped battery to a T-Connector for use with a T-Connector equipped ESC or Charge lead.

Spec:
Weight: 9g(Each)

Mini black T Connector pack (5 Pairs)

Specs:
Base Dimensions: 5mm x 8mm
Contact Dimension: 3mm x 5mm x 1mm
Rating: 10amps continuous

Super flexible 26AWG twisted silicone male to male servo lead. These are specifically made as signal leads for RX to Flight controller connections, the light 26AWG silicone wire is so flexible it transfers virtually no vibration to the Flight controller, well the twist helps reduce inducted noise. If used in conjunction of having only one lead vertical and the other leads turned on their side for signal only, makes for a clean and minimal vibration transfer installation. Or better yet a single CPPM/SBUS single lead. 

Specs:
Length: 130mm(black/red/white)
Connection: Male JR style plug on each end.

Super flexible 26AWG twisted silicone male to male servo lead. These are specifically made as signal leads for RX to Flight controller connections, the light 26AWG silicone wire is so flexible it transfers virtually no vibration to the Flight controller, well the twist helps reduce inducted noise. If used in conjunction of having only one lead vertical and the leads turned on their side for signal only makes for a clean and minimal vibration transfer installation, or better yet a single CPPM/SBUS single lead.

Specs:
Length: 80mm(black/red/white)
Connection: Male JR style plug on each end.

Mini Tamiya to T-Connector Battery Adapter (2pcs/bag)

This adapter will convert a Mini Tamiya equipped battery to a T-Connector for use with a T-Connector equipped ESC or a T-Connector Charge lead.

A handy adapter to convert an XT60 equipped battery to an MPX style connector. Useful for use with MPX equipped ESC or Charge leads.

Spec:
Weight: 5.3g(Each)

HXT 4mm bullet to XT90 Battery Adapter (2pcs)

This adapter will convert a 4mm bullet equipped battery to a XT90 for use with a XT90 equipped ESC or a XT90 Charge lead.

XT90 to 4.0mm bullet Battery Adapter (2pcs/bag)

This adapter will convert a XT90 equipped battery to a 4.0mm bullet for use with a 4.0mm bullet equipped ESC or a 4.0mm bullet Charge lead.

Hobbyking Bixler 2 EPO 1500mm - Replacement Pushrod Set

This is a great way to avoid power shorts.

Gold connectors on their own are notorious for creating a short circuit and looking messy. Use these to keep your connections safe and looking neat!

Rated to 20Amp these connectors are an excellent replacement for JST plugs on todays small yet high C rated batteries.