Bargain Bin

Desert Fox Dirt Proof Cover (Clear) (1 set)

BT-4 Rear Suspension Arm Mount R2.0 TU1007

BT-4 Straight shaft (Spool) TU1042-2

Progressive Shock system for BT-4 gives a progressive dampening effect through the shock travel so the effect is softest at the start and harder at the end. Includes blank shock pistons so you can drill your own holes for precise tuning to your individual needs.

Specs:
Length: 14mm
Diameter: 11mm
Piston: 10mm x 2mm

A kit of plywood parts for the Durafly Tundra V1, V2, V3, and Night to build a mount/tray for your FPV equipment. The Tundra series is the perfect mount for FPV flying due to its stability and slow flying characteristics.

Basher RZ-4 1/10 Rally Racer - Composite Rear Upright (2pcs)

Clear Body - Basher PBull 1/18 4WD Desert Buggy

TrackStar Shock Bottom Cap Set with O-Ring S120052

Compatible with the following Shock Absorbers
S12400, S160023, S160026, S160085, S160100, S124300, S160323, S160326

TrackStar Hardened Shock Shaft (x4)

Specs:
Diameter: 3.2mm
Length:48mm

Compatible with the following Shock Absorbers
S160100

TrackStar Suspension Spring (x4)

Specs:
Wire Thickness: 1.1mm
Internal Diameter: 14mm
Length: 55mm
Spring Rate:  1.2Kg
Color: Gold

Compatible with the following Shock Absorbers
S160023, S160026, S160323, S160326

Pulse / Heart Rate Sensor Module for Arduino

Specs:
Dimensions: 15 x 2mm
Weight: 2.66g

On screen display (OSD) module for Shark X6/X8 flight controllers.

Specs:
Input voltage: 5V DC
Operating Temperature: -10°C ~ 50°C
Cable length: 130mm
Dimensions: 33 x 20 x 11mm
Weight: 10.5g 

Included:
OSD module

One of a series of four DIY robot car kits, these are great value and great fun for kids of all ages to put together.

You will only need some basic tools, some solder and a soldering iron and within a few hours you will have an operating robot car.

This model is activated by light sensor and will respond to a flashlight or other direct light source.

Includes:
1 x Light controlled robot car kit 

Note: This robot does not require programming.

One of a series of four DIY robot car kits, these are great value and great fun for kids of all ages to put together.

You will only need some basic tools, some solder and a soldering iron and within a few hours you will have an operating robot car.

This model is an obstacle avoider, with a sensor that detects objects to its front. 

Includes:
1 x Obstacle avoiding robot car kit 

Note: This robot does not require programming.

Make use of that free wind power electricity!

For use with the EK5100 Wind Turbine kit is this versatile charging unit.

Simply connect it up to your wind turbine and it can be used to charge your mobile phone, your ipod or your rechargable batteries. 

Includes:
Ek5400 Charger
Leads and cables

Make light and music with that free wind power electricity!

For use with the EK5100 Wind Turbine kit is this melody and light board.

Simply connect it up to your wind turbine and it can be used to power the sound and light board in various modes.

Includes:
Ek5300 Board
Instructions

Spare Part - Premium BNC 1.3m RG223 cable for Scherrer Rx700LR Long Range UHF system

Soldering Iron Tip Set (10 pcs)

Suits Hakko type soldering irons that have an attachment spigot diameter of 4mm. Containing fine tips to bevel edges, this pack has you covered for the majority of hobby projects from PCB soldering to battery connectors. 

Reliably monitor the voltage of your battery with the Turnigy TGY-CVT01 Voltage Sensor.

As a great alternative to setting a timer, fly or drive your model based on the actual voltage of your battery. This way if your voltage drops quicker than usual due to harder running, you can avoid over discharge your pack. Or, perhaps you're having a nice relaxed day? Enjoy longer run times and don't cut yourself short.

This small, compact sensor is also a perfect way to add piece of mind when running a high performance model by allowing you to check that the battery voltage isn't dropping excessively under load.

For use with the TGY- i10 and i6 transmitters and TGY-iA10 and i6 V2 receivers.

Designed to daisy chain together with other TGY-C series sensors.

Features:
• High quality, compact sensor
• Futaba style input and output connectors
• Great for monitoring battery voltage, no need to set timers anymore
• Works with TGY- i10 and i6 transmitters and TGY-iA10 and i6 V2 receivers

Specs:
Voltage Range: 0~100V DC
Accuracy: +/- 0.1V
Input Voltage: 4.0~6.5V
Working Current: 9mA
Lead length: 195mm
Size: 31 x 15 x 8.5mm
Weight: 6.25g (inc leads and sensor)

Turnigy 9XR FPV Monitor Mounting Arm.

A mounting arm specially designed to hold Telemetry units or FPV Monitors on
top of your 9XR.
Compatible with most standard FPV monitors and our Quanum Telemetry system.

*Requires the 9XR Transmitter Stand (see related items)

3x30P Pin Socket - 2.54mm Pitch (5pcs/bag)

Perfect for DIY electronics projects.

When it comes to hardware, quality does matter! These titanium machine screws not only offer improved strength over steel, they are also much lighter in weight. These are ideal for use in performance models where shaving weight is absolutely critical, or for any project requiring high strength, lightweight hardware.

Spec.:
Size: M2.5 x 8mm
Weight: 0.18g(Each)

When it comes to hardware, quality does matter! These titanium machine screws not only offer improved strength over steel, they are also much lighter in weight. These are ideal for use in performance models where shaving weight is absolutely critical, or for any project requiring high strength, lightweight hardware.

Spec.:
Size: M2.5 x 8mm
Weight: 0.20g(Each)

This high quality switch is made in Taiwan and is proven to exceed more than 10000 switch cycles during testing.
This switch is designed for life time use.

Great for repairing your radio or making a swtich for your own project.

Spec.:
Style: 2-Way, Round Head
Dimension(LxWxD): 13x8x7mm(Plastic part only)
Length: 29mm(Switch & Mounting hole)
Mounting Hole Size: M6x8mm
Weight: 3.7g(Each)

30P Pin Header and Socket - 2.54mm Pitch (5 pcs)

Perfect for DIY electronic projects.

The cable tie clip mounting set is the perfect solution for the modeller who likes a neat and tidy install. The clips provide slots for cable ties up to 4mm width and can be simply glued in onto the desired position within your model.

The clips are suitable for fiberglass, foam or wooden models but can be used for almost any application.     

Specs:
Material: ABS Plastic
Weight Per Set: 11g
Fits: 4mm cable ties

Trackstar V2 motor front case with bearing and isolator paper.

Modified rotor for Trackstar V2 motors.
This rotor has a permanent sintered neodymium N38UH magnet.
Includes washer and spacer set. 

Specs:
Magnet: N38UH Neodymium Magnet
Dimensions: 12 x 5 x 25.3mm
Shaft: 5 x 12.25mm

These new prop hubs are ideal for achieving that finished look to your model and the new raised motor mount will assist in providing some additional clearance for the back of the shaft against the model's firewall.

This package will fit the SK3 Series of motors in the following sizes only: 2822, 2826, 2830, 2836.

Includes:
1 x Prop hub
1 x motor mount
4 x mounting screws

Get an unfair advantage with Turnigy Nano-tech Airsoft Packs!

On the battlefeild, no one wants to compromise on fire power! That's why the legendary Turnigy nano-tech batteries are available as a drop-in replacement pack for an upgrade in firepower. 

Turnigy Nano-tech Airsoft batteries are superior to the standard NiMH batteries offering faster charge rates and higher voltages. In short, the first thing your opponent will notice is sustained rapid fire pinning him down.

It's clear why Turnigy Nano-techs are the go to pack for anyone who is serious about Airsoft.

Spec.
Capacity: 1000mAh
Voltage: 3S1P / 3S Cell / 11.1V
Discharge: 20C Constant / 40C Burst
Weight: 72g (including wire, plug & case)
Dimensions: 101x20x16mm
Balance Plug: JST-XH
Discharge Plug: Mini-Tamiya (Mini Molex)

Advantages over traditional Lipoly batteries;
• Power density reaches 7.5 kw/kg.
• Less Voltage sag during high rate discharge, giving more power under load.
• Internal impedance can reach as low as 1.2mO compared to that of 3mO of a standard Lipoly.
• Greater thermal control, pack usually doesn’t exceed 60degC
• Swelling during heavy load doesn’t exceed 5%, compared to 15% of a normal Lipoly.
• Higher capacity during heavy discharge. More than 90% at 100% C rate.
• Fast charge capable, up to 15C on some batteries.
• Longer Cycle Life, almost double that of standard lipoly technology.

The nano-core technology in lithium ion batteries is the application of nanometer conductive additives. The nanometer conductive additives form ultra-strong electron-conducting networks in the electrodes which can increase electronic conductivity.

These additives create the ability for imbibition in the carrier liquid to supply more ion channels.This improves the ability of ion transmission and ion diffusion. Through improving electronic conductivity and ion transmission, the impedance is reduced and the polarization of high rate discharge decreases greatly.

*The length of balance charging wire may vary

Get an unfair advantage with Turnigy Nano-tech Airsoft Packs!

On the battlefeild, no one wants to compromise on fire power! That's why the legendary Turnigy nano-tech batteries are available as a drop-in replacement pack for an upgrade in firepower. 

Turnigy Nano-tech Airsoft batteries are superior to the standard NiMH batteries offering faster charge rates and higher voltages. In short, the first thing your opponent will notice is sustained rapid fire pinning him down.

It's clear why Turnigy Nano-techs are the go to pack for anyone who is serious about Airsoft.

Spec.
Capacity: 1000mAh
Voltage: 3S1P / 3S Cell / 11.1V
Discharge: 20C Constant / 40C Burst
Weight: 78g (including wire, plug & case)
Dimensions: 104x22x7.5mm (Each)
Balance Plug: JST-XH
Discharge Plug: Mini-Tamiya (Mini Molex)

Advantages over traditional Lipoly batteries;
• Power density reaches 7.5 kw/kg.
• Less Voltage sag during high rate discharge, giving more power under load.
• Internal impedance can reach as low as 1.2mO compared to that of 3mO of a standard Lipoly.
• Greater thermal control, pack usually doesn’t exceed 60degC
• Swelling during heavy load doesn’t exceed 5%, compared to 15% of a normal Lipoly.
• Higher capacity during heavy discharge. More than 90% at 100% C rate.
• Fast charge capable, up to 15C on some batteries.
• Longer Cycle Life, almost double that of standard lipoly technology.

The nano-core technology in lithium ion batteries is the application of nanometer conductive additives. The nanometer conductive additives form ultra-strong electron-conducting networks in the electrodes which can increase electronic conductivity.

These additives create the ability for imbibition in the carrier liquid to supply more ion channels.This improves the ability of ion transmission and ion diffusion. Through improving electronic conductivity and ion transmission, the impedance is reduced and the polarization of high rate discharge decreases greatly.

*Note: The length of Balance charging wire may vary

When it comes to putting rounds down range, no one wants to compromise on fire power! thats why the legendary Turnigy nano-tech batteries are now available for Airsoft combat. Higher motor RPM, less voltage sag and extended operating times equal better performance from your weapon of choice.

The nano-tech Airsoft series also feature 5C charge ratings putting you back on the front line faster!

Get an unfair advantage and make sure your opponents know that they have been taken out by nano-tech!

Get an unfair advantage with Turnigy Nano-tech Airsoft Packs!

On the battlefeild, no one wants to compromise on fire power! That's why the legendary Turnigy nano-tech batteries are available as a drop-in replacement pack for an upgrade in firepower. 

Turnigy Nano-tech Airsoft batteries are superior to the standard NiMH batteries offering faster charge rates and higher voltages. In short, the first thing your opponent will notice is sustained rapid fire pinning him down.

It's clear why Turnigy Nano-techs are the go to pack for anyone who is serious about Airsoft

Spec.
Capacity: 1200mAh
Voltage: 2S1P / 2S Cell / 7.4V
Discharge: 25C Constant / 50C Burst
Weight: 59g (including wire, plug & case)
Dimensions: 118x16x7mm (Each)
Balance Plug: JST-XH
Discharge Plug: Mini-Tamiya (Mini Molex)

Advantages over traditional Lipoly batteries;
• Power density reaches 7.5 kw/kg.
• Less Voltage sag during high rate discharge, giving more power under load.
• Internal impedance can reach as low as 1.2mO compared to that of 3mO of a standard Lipoly.
• Greater thermal control, pack usually doesn’t exceed 60degC
• Swelling during heavy load doesn’t exceed 5%, compared to 15% of a normal Lipoly.
• Higher capacity during heavy discharge. More than 90% at 100% C rate.
• Fast charge capable, up to 15C on some batteries.
• Longer Cycle Life, almost double that of standard lipoly technology.

The nano-core technology in lithium ion batteries is the application of nanometer conductive additives. The nanometer conductive additives form ultra-strong electron-conducting networks in the electrodes which can increase electronic conductivity.

These additives create the ability for imbibition in the carrier liquid to supply more ion channels.This improves the ability of ion transmission and ion diffusion. Through improving electronic conductivity and ion transmission, the impedance is reduced and the polarization of high rate discharge decreases greatly.

*The length of balance charging wire may vary

Get an unfair advantage with Turnigy Nano-tech Airsoft Packs!

On the battlefeild, no one wants to compromise on fire power! That's why the legendary Turnigy nano-tech batteries are available as a drop-in replacement pack for an upgrade in firepower. 

Turnigy Nano-tech Airsoft batteries are superior to the standard NiMH batteries offering faster charge rates and higher voltages. In short, the first thing your opponent will notice is sustained rapid fire pinning him down.

It's clear why Turnigy Nano-techs are the go to pack for anyone who is serious about Airsoft.

Spec.
Capacity: 1200mAh
Voltage: 3S1P / 3S Cell / 11.1V
Discharge: 25C Constant / 50C Burst
Weight: 85g (including wire, plug & case)
Dimensions: 120x17x7.5mm (Each)
Balance Plug: JST-XH
Discharge Plug: Mini-Tamiya (Mini Molex)

Advantages over traditional Lipoly batteries;
• Power density reaches 7.5 kw/kg.
• Less Voltage sag during high rate discharge, giving more power under load.
• Internal impedance can reach as low as 1.2mO compared to that of 3mO of a standard Lipoly.
• Greater thermal control, pack usually doesn’t exceed 60degC
• Swelling during heavy load doesn’t exceed 5%, compared to 15% of a normal Lipoly.
• Higher capacity during heavy discharge. More than 90% at 100% C rate.
• Fast charge capable, up to 15C on some batteries.
• Longer Cycle Life, almost double that of standard lipoly technology.

The nano-core technology in lithium ion batteries is the application of nanometer conductive additives. The nanometer conductive additives form ultra-strong electron-conducting networks in the electrodes which can increase electronic conductivity.

These additives create the ability for imbibition in the carrier liquid to supply more ion channels.This improves the ability of ion transmission and ion diffusion. Through improving electronic conductivity and ion transmission, the impedance is reduced and the polarization of high rate discharge decreases greatly.

*The length of balance charging wire may vary