Bargain Bin
-
Male-to-Male Silicone Servo Leads 26AWG (JR) 130mm 5pcs/bag$2.26Super flexible 26AWG twisted silicone male to male servo lead. These are specifically made as signal leads for RX to Flight controller connections, the light 26AWG silicone wire is so flexible it transfers virtually no vibration to the Flight controller, well the twist helps reduce inducted noise. If used in conjunction of having only one lead vertical and the other leads turned on their side for signal only, makes for a clean and minimal vibration transfer installation. Or better yet a single CPPM/SBUS single lead.
Specs:
Learn More
Length: 130mm(black/red/white)
Connection: Male JR style plug on each end. -
Male-to-Male Silicone Servo Leads 26AWG (JR) 80mm 5pcs/bag$2.42Super flexible 26AWG twisted silicone male to male servo lead. These are specifically made as signal leads for RX to Flight controller connections, the light 26AWG silicone wire is so flexible it transfers virtually no vibration to the Flight controller, well the twist helps reduce inducted noise. If used in conjunction of having only one lead vertical and the leads turned on their side for signal only makes for a clean and minimal vibration transfer installation, or better yet a single CPPM/SBUS single lead.
Specs:
Learn More
Length: 80mm(black/red/white)
Connection: Male JR style plug on each end. -
Mini Tamiya to T-Connector Battery Adapter (2pcs/bag)$3.02Mini Tamiya to T-Connector Battery Adapter (2pcs/bag)
Learn More
This adapter will convert a Mini Tamiya equipped battery to a T-Connector for use with a T-Connector equipped ESC or a T-Connector Charge lead. -
XT60 Male to MPX Female 2pcs/bag$3.24A handy adapter to convert an XT60 equipped battery to an MPX style connector. Useful for use with MPX equipped ESC or Charge leads.
Learn More
Spec:
Weight: 5.3g(Each) -
HXT 4mm Bullet to XT90 Battery Adapter (2pcs)$4.14HXT 4mm bullet to XT90 Battery Adapter (2pcs)
Learn More
This adapter will convert a 4mm bullet equipped battery to a XT90 for use with a XT90 equipped ESC or a XT90 Charge lead. -
XT90 to 4.0mm bullet Battery Adapter (2pcs/bag)$5.37XT90 to 4.0mm bullet Battery Adapter (2pcs/bag)
Learn More
This adapter will convert a XT90 equipped battery to a 4.0mm bullet for use with a 4.0mm bullet equipped ESC or a 4.0mm bullet Charge lead. -
Hobbyking Bixler 2 EPO 1500mm - Replacement Pushrod Set$3.27Hobbyking Bixler 2 EPO 1500mm - Replacement Pushrod Set
Learn More -
HXT 2mm Gold Connector w/ Protector (10pcs/set)$3.61This is a great way to avoid power shorts.
Gold connectors on their own are notorious for creating a short circuit and looking messy. Use these to keep your connections safe and looking neat!Rated to 20Amp these connectors are an excellent replacement for JST plugs on todays small yet high C rated batteries.
Learn More -
Turnigy D2830-11 1000kv Brushless Motor$14.50Learn MoreD2830-11 1000kv Brushless MotorSpecs:Rpm/V: 1000kvShaft: 3.17mm
Voltage: 2S~4S (7.4v to 14.8v)Weight: 52gWatts: 210w
Max Current: 21A
ESC: 30A
Suggested Prop: 8x4 (4S) ~ 10x7 (2S)
Mounting Hole Bolt Circle: 16mm or 19mmNOTE: This motor is 1000kv. The factory labelled them 1100kv in error. -
FPV Tilt Camera Mount with Landing Gear$21.99The HobbyKing FPV tilt camera mounting system is a simple and easy way to mount your camera. Suitable for 450~500 class helicopters and made from light weight fibre glass material. The mounting plate features adjustable screw locations for mounting your heli and for relocating the camera mount to attain correct CoG. Kit includes screws, ball sockets, connection rods, linkages and pre-cut fiberglass board.Spec:Height: 185mm (to mounting plate)
Skid width: 190mm
Skid length: 290mm
Camera mount area width: 110mm
Camera mount area height: 100mm
Dry Weight: 188g (not including servo)Material: Fibre Glass
Required:1 x 9g ServoLearn More -
Insta-Cure IC-Gel .7 oz$6.88Insta-Cure IC-Gel .7 ozIC-GEL is a cyanoacrylate paste that is extremely thick which comes in an applicator tube like toothpaste. It has the same bonding and curing time characteristics as MAXI-CURE; IC-Gel, however, can be applied to a vertical surface and will stay in place. It will not run. This can be very convenient for some assembly applications. Applying CA to the bottom of a horizontal surface, such as a ceiling, can be very difficult with anything other than a full standard CA bottle. IC-GEL can be applied at any angle with just a squeeze of the tube. The gel does, however, have a tendency to continue to come out of the tube for about a second after pressure is released, so this must be taken into account to apply the exact amount of IC-GEL that you want.IC-GEL is an excellent putty for plastic models. It will fill any void and can be formed to many shapes. Applying INSTA-SET allows IC-GEL to be sanded or filed to final shape in less than 20 seconds. Autobody repairmen have finished their jobs in a fraction of the time by using IC-GEL with the additional advantage over normal body putties of superior bonding to metal surfaces. IC-GEL, along with MAXI-CURE, is also used for the underwater bonding of coral to rock.Learn More -
Insta-Set CA Accelerator 2. oz$5.42Insta-Set CA Accelerator 2. ozINSTA-SET is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET significantly enhances a joints strength. For difficult to bond materials, INSTA-SET can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.Learn More -
HK-171 Thread Locker & Sealant Medium Strength (Blue)$4.99HK-171 is a medium thickness, medium strength threadlock that is applied to the threads of fasteners before assembly. Once HK-171 is cured, the fasteners can be disassembled with standard hand tools if required.Learn More -
HobbyKing® ™ GT-2 2.4Ghz Receiver 3Ch$7.60HobbyKing® ™ GT-2 2.4Ghz Receiver 3Ch.Please note: This receiver is compatible with the GT2E radio, the radio however will need to be switched to AFHDS1 protocol mode, this is outlined in the radio's user manual.Specification:Model: Car/BoatChannels: 3chFrequency band: 2.4GhzModulation: GFSKSensitivity: 1024RF. receiver sensitivity: -100dbmFail Safe: YesPower: 4.5~6VDCWeight: 5gAntenna length: 26mmSize: 37.6 x 22.3 x 13mmCE & FCC certified
Learn More -
HobbyKing® Bixler 3 Trainer 1550mm - Replacement Wheel Pant Set$3.81HobbyKing® Bixler 3 Trainer 1550mm - Replacement Wheel Pant Set
Learn More -
HobbyKing® Bix3 Trainer 1550mm - Replacement Control Rod Set$3.87HobbyKing® Bix3 Trainer 1550mm - Replacement Control Rod Set
Learn More -
HobbyKing® Bix3 Trainer 1550mm - Replacement Prop Adapter$3.55HobbyKing® Bix3 Trainer 1550mm - Replacement Prop Adapter
Learn More -
Nylon Spinner with Alloy Backplate 70mm Black$8.47Excellent Quality Nylon Spinner with Lightened Alloy Backplate 70mm Yellow - Mount hole 8mm
Learn MoreWeight: 47g
-
Desert Fox Printed Body Panels Full Set (1 set)$16.09Desert Fox Printed Body Panels Full Set (1 set)
Learn More -
-
Desert Fox Dirt Proof Cover (Clear) (1 set)$11.84Desert Fox Dirt Proof Cover (Clear) (1 set)
Learn More -
BT-4 Rear Suspension Arm Mount R2.0 TU1007$8.53BT-4 Rear Suspension Arm Mount R2.0 TU1007
Learn More -
-
Progressive Shock System for BT-4$19.24Progressive Shock system for BT-4 gives a progressive dampening effect through the shock travel so the effect is softest at the start and harder at the end. Includes blank shock pistons so you can drill your own holes for precise tuning to your individual needs.
Specs:
Learn More
Length: 14mm
Diameter: 11mm
Piston: 10mm x 2mm -
Durafly Plywood Equipment Mount for FPV Flying (Kit)$3.99A kit of plywood parts for the Durafly Tundra V1, V2, V3, and Night to build a mount/tray for your FPV equipment. The Tundra series is the perfect mount for FPV flying due to its stability and slow flying characteristics.
Learn More -
Basher RZ-4 1/10 Rally Racer - Composite Rear Upright (2pcs)$7.98Basher RZ-4 1/10 Rally Racer - Composite Rear Upright (2pcs)
Learn More -
Clear Body - Basher PBull 1/18 4WD Desert Buggy$10.47Clear Body - Basher PBull 1/18 4WD Desert Buggy
Learn More -
TrackStar Shock Bottom Cap Set with O-Ring S120052$5.31TrackStar Shock Bottom Cap Set with O-Ring S120052
Compatible with the following Shock Absorbers
Learn More
S12400, S160023, S160026, S160085, S160100, S124300, S160323, S160326 -
TrackStar Hardened Shock Shaft 3.2 x 48mm (4) S162048$3.72TrackStar Hardened Shock Shaft (x4)
Specs:
Diameter: 3.2mm
Length:48mmCompatible with the following Shock Absorbers
Learn More
S160100 -
TrackStar Suspension Spring Gold 14 x 55mm 1.2KG (4) S169355$3.60TrackStar Suspension Spring (x4)
Specs:
Wire Thickness: 1.1mm
Internal Diameter: 14mm
Length: 55mm
Spring Rate: 1.2Kg
Color: GoldCompatible with the following Shock Absorbers
Learn More
S160023, S160026, S160323, S160326 -
Pulse / Heart Rate Sensor Module for Arduino$11.74Pulse / Heart Rate Sensor Module for Arduino
Learn More
Specs:
Dimensions: 15 x 2mm
Weight: 2.66g -
OSD Module for Shark X6/X8 Flight Controllers$34.28On screen display (OSD) module for Shark X6/X8 flight controllers.
Specs:
Input voltage: 5V DC
Operating Temperature: -10°C ~ 50°C
Cable length: 130mm
Dimensions: 33 x 20 x 11mm
Weight: 10.5gIncluded:
Learn More
OSD module -
EK3560 Light Follower Car$5.84One of a series of four DIY robot car kits, these are great value and great fun for kids of all ages to put together.
You will only need some basic tools, some solder and a soldering iron and within a few hours you will have an operating robot car.This model is activated by light sensor and will respond to a flashlight or other direct light source.
Learn More
Includes:
1 x Light controlled robot car kit
Note: This robot does not require programming. -
EK3170 OBSTACLE AVOIDER$7.23One of a series of four DIY robot car kits, these are great value and great fun for kids of all ages to put together.
You will only need some basic tools, some solder and a soldering iron and within a few hours you will have an operating robot car.This model is an obstacle avoider, with a sensor that detects objects to its front.
Includes:
1 x Obstacle avoiding robot car kitNote: This robot does not require programming.
Learn More
Login and Registration Form